Search Documents

By N. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract J0377014, "Development and Evaluation of Noise Control Techniques for Taconite Processing Equipment." Three areas of taconite processing equipment, grinding mills, fine screens, and crusher screens have been investigated. Extensive noise and vibration measurements have been made on grinding mills in which the process parameters that affect mill noise have been identified, and the level of shell impact noise around the mill defined. A multiplexing telemetry system was used to obtain shell vibration measurements from a rotating mill. Mill noise control methods were investigated and a partial mill barrier was built and tested on a semi-autogeneous mill. A noise reduction of approximately 3 to 6 dBA was achieved on the falling side of the mill. The use of rubber mill liners on autogenous mills has been evaluated. The noise sources on fine screens have been quantified, and noise control treatments developed. Noise reductions of 11 to 13 dBA were achieved at positions around the fine screen and some in-service testing has been done. Noise measurents of crusher screens were obtained and noise control through resilient screen decks appears to hold the most promise. Additional benefits might be lower life-cycle cost, since the service life of resilient decks is claimed to be longer than steel.

Jan 1, 1983

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

A broker relies heavily on mineral valuations and independent experts' reports to provide the fundamental information, both technical and commercial, which provides the basis of estimating the sharemarket value of securities and underlying assets. It is important to appreciate the significant variance that can occur between the market value and other types of valuation at a particular point in time. In general, most experts' reports and valuations seek to provide estimates of technical/fundamental or ""fair"" value which correspond to the Corporations Law and accounting standards requirements. They do not usually attempt to estimate (stock) market values and it is usually and quite correctly the broker's task to estimate market values on the basis of a technical appraisal and consideration of all other commercial, market and financial influences. Therefore ideally, an independent experts' report or information memorandum will include material relating to commercial and management aspects of a company as well as detailed technical reviews and fundamental valuations. Wherever sensible cash flow projections can be made, cash flow-derived valuations, usually based on discounted cash flow (DCF) calculations, remain the preferred valuation methodology. Brokers in general would not argue with this preference. However, there is a paucity of examples of valuations where alternative methods are applied as a check on the reasonableness of a DCF-based estimate.

Jan 1, 1994

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Morgana Rosset, Bárbara da Rocha Pereira

High-purity alumina finds application in various electronic industry sectors, with approximately 100 million tons of this compound being produced worldwide. Alumina is acquired through the mining process of bauxite, a rock composed of a mixture of minerals such as gibbsite, kaolinite, hematite, and either anatase or rutile. In 2020, both bauxite and alumina were included in the list of critical raw materials. Due to the demand for high-purity alumina production, the development of a methodology to remove impurities present in the leach liquor from bauxite processing by solvent extraction (SX) followed by precipitation has been widely studied. This work aims to obtain high-purity alumina from bauxite by a solvent extraction process followed by a precipitation step from the sulfur leach liquor obtained by the thorough dissolution of Al and Fe from bauxite. Different parameters were evaluated in the SX step, such as extractant type, pH, temperature, and volume-to-volume ratio. The results indicated that using Alamine 336 as an extractant at pH 0 and room temperature led to an extraction of 90% of Fe and 15% of Al. Aluminum sulfate was completely precipitated as aluminum hydroxide and 55% of Fe using NH4OH. After the calcination procedure, obtaining a 99.9% pure alumina was possible without generating a red mud-similar residue.

Dec 28, 2023

By M. Vallée

Several reviews of mineral project performance in the past 35 years indicate a pattern of occasional, but recurrent, mining project failures due to shortcomings in geological information and estimation, mineral processing and metallurgical testing, feasibility study objectives and requirements, and project start-up methods. A commitment to quality assurance and continuous improvement methods and to obtaining “ENOUGH DATA, OF APPROPRIATE QUALITY” is essential. Recent international and Canadian proposals for mineral resource and ore reserve definitions have taken a nonprescriptive stance that will undermine the formulation of requirements, guidelines and industry standards for efficient deposit delineation and estimation, and for the determination of project feasibility. To help reduce problems, every feasibility study supporting a mine development and production decision should be based on objectives and methods adequate to reach completion targets similar to the bankers’, as a good business target for a profitable project. In a resource/reserve system, the use of reserve should be restricted to a project that meets required technical, economic and legal feasibility requirements for successful project implementation, and the definitions of these categories should provide explicit limits. Current shortcomings will limit the ability of the Qualified Person to provide “adequate professional practice,” fulfill his/her professional responsibilities to his employer or client and provide adequate information to the investing public. We must take advantage of present opportunities for Setting New Standards for the new Millennium.

Jan 1, 2000

By C. A. Lavery

A DISCUSSION is presented of natural gas production and field processing equipment as now utilized in the gas producing areas of the United States, with reference to use of such equipment in Canadian gas areas. The scope of the paper is confined to a general description of various types and methods of using surface production equipment. The discussion is divided under two general groups: well-head production equipment, and field processing. The first will be concerned primarily with indirect heaters, separators, knockouts, and special versions of this equipment. The second major group includes the field processing equipment for handling natural gas. A delineation should be made here as to the meaning of field processing as used in this discussion. We will limit our term to mean such processing equipment as may be used in producing fields to process gas or its by products in a manner that does not require conventional plant practices either in operation or supervision. This covers such equipment as is necessary to complete preparation of gas for sale to pipeline and/ or is necessary to recover valuable components. Under this heading we will discuss glycol dehydration, solid desiccant dehydration, low-temperature separation, mechanical refrigeration, and desorbtion-stabilization. These are all processes involved in preparing gas for final sale or disposal. They do not include the more conventional and large-scale plant process systems.

Jan 1, 1956

By M. R. Peterson

The U.S. Bureau of Mines investigated column flotation for recovery of a high-grade fluorite (CaF2) concentrate and byproduct concentrates from the Fish Creek fluorite deposit in Eureka County, NY. The recovery scheme consisted of (1) grinding the ore to minus 48 mesh, (2) fluorite rougher and cleaner flotation, (3) desliming the rougher fluorite flotation tailings at 20 Jjm, (4) mica flotation, and (5) silicate rougher flotation. Acid-grade fluorspar, mica, free silica (Si02) sand, and low-grade beryl (Be3Al2S~018) concentrate were produced in a 100 lb/h continuous column flotation unit (CCFU). The highest results achieved were %.6-pct CaF2 recovery in a fIrst cleaner concentrate containing 99.7 pct CaF2. Beryl recovery was as high as 92 pct at a grade of 5.3 pct BeO. The silica sand, which assayed 98 pct Si02, was recovered as the rougher beryl flotation tailings. Collector reagent consumption was reduced 45 pct for fluorite and 58 pet for silicate flotation in comparison with bench-scale conventional flotation. All products were signillcantly improved in both grade and recovery over conventional flotation results, and the recovery scheme was simplifIed by removal of several stages of flotation in the fluorite and silicate flotation steps.

Jan 1, 1990

By P Breuer, X Dai, A Bergamin, D Hewitt

"Copper-ammonia-thiosulfate?leaching of gold has been researched for several decades as a potential alternative to cyanidation. However, this technology has not yet been applied commercially due to many challenges such as complex solution chemistry, reagent degradation and losses, system instability with losses of precious metals and difficulties in gold recovery from the leachate. Progress has been made at CSIRO in tackling some of these challenges including:better understanding and control of the leach conditions to minimise reagent losses whilst maximising gold recovery use of strong base ion exchange resins to recover the gold strategies to deal with polythionates that adsorb competitively with gold on ion exchange resins development and evaluation of process flow sheets.As a result there has been increased interest from the gold industry and renewed activities to develop thiosulfate based processes for gold recovery. One application area, which has been developed to the point of piloting, is the treatment of gravity gold concentrates using a copper-ammonia-thiosulfate leach with ion exchange recovery of the gold thiosulfate. This paper describes some of the advancements in the development of a potential process flow sheet for this application.CITATION:Dai, X, Breuer, P, Hewitt, D and Bergamin, A, 2013. Thiosulfate process for treating gold concentrates, in Proceedings World Gold 2013, pp 61-70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

By Randall D. Peterson

Strip mining with draglines and other surface equipment has traditionally been the method of choice for mining shallow deposits. This is particularly true for soft deposits that require little or no blasting. High rates of productivity and low operating costs have set this standard. However, these methods can be improved. Strip mining methods are batch processes and difficult to accommodate in processing. Moreover, they are encumbered with overburden removal, reclamation expense, and human inefficiencies. This paper describes the invention of a novel shallow earth mining technique called the Softwall Mining Method. Softwall Mining is an adaptation of longwall mining for loose earth conditions. The method was specifically invented for recovering phosphatic clay ore from beds in North Central Florida, but is likely to be suitable for a number of other minerals as well. Potential deposits for which the method may be well suited include placers, disseminated deposits in soft host rocks, bauxite, soft coals and lignite deposits, and other deposits where overburden will subside readily and where the ore can be hydraulically broken and slurried. Unit operating cost advantages are expected over the current dragline systems used. The Softwall mining advantages are its high rates of productivity, control and automation of the mining process, reduction of dilution and waste, and elimination of the majority of stripping and reclamation.

Jan 1, 1998

By E. R. Cole

The Bureau of Mines developed a procedure that enables substitution of zinc cathodes for the aluminum cathodes normally used in commercial zinc electro-winning. Using zinc cathodes eliminates the necessity for stripping and makes it possible to electrowin zinc from solutions derived from material containing excessive amounts of soluble fluorides; for example, zinc concentrates obtained as a byproduct of fluorspar mining in Kentucky and Illinois. To demonstrate the viability of using zinc cathodes, fluoride-containing zinc concentrate was roasted, leached, and purified according to current commercial practice. Electrolysis was carried out in 0.8-, 1-, 5, and 10-liter cells at 35° to 40° C with a cathode-current density of 8 amp/dm2 in a solution containing 65 g/l Zn++ and 200 g/l H2S04 using PbO2 anodes. Zinc deposits were produced on zinc cathodes with good morphology and excellent current efficiency (90 to 94 pct) in solutions containing enough fluoride (~0.5 g/l, F+) to cause sticking of zinc to aluminum cathodes. The approach described has failed previously because of severe solution-level corrosion of the zinc cathodes. The present investigation found that the use of a simple mechanical barrier to prevent oxygen migration from the anode was sufficient to prevent solution-level corrosion of the zinc cathode starting sheet.

Jan 1, 1979

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By William E. Roscoe

"Valuation methods are well established for mineral properties with production or imminent production, and include discounted cash flow and comparable transactions. Valuation methods for non-producing mineral properties, however, are more subjective. Non-producing mineral properties include those at various stages of exploration, properties at the prefeasibility or feasibility stage, properties with currently uneconomic mineral resources, and past-producers. Different valuation methods may be appropriate for different types of mineral properties.Income approach methods such as discounted cash flow and option pricing are generally not applicable to properties at the exploration stage. The market approach is generally appropriate to all types of mineral properties, although it is difficult to find good comparables because of the unique nature of mineral properties and the small number of transactions. Cost approach methods, such as appraised value and geoscience factor, are commonly used for exploration stage properties.Canadian standards and guidelines for valuation of mineral properties are in the process of being finalized by a Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIMVal Committee). The CIMVal Standards are intended to be consistent with National Instrument 43-101, which sets regulatory standards of disclosure for mineral projects, and with International Valuation Standards. The intent of the CIMVal Standards and Guidelines is that mineral property valuation be carried out by appropriately qualified individuals and that all relevant information be disclosed."

Jan 1, 2003

By C. H. Schack, K. C. Dean

An investigation was made to devise and evaluate a flexible flotation method for beneficiating typical tactite types of calcareous scheelite - bearing ores ; these scheelite - bearing ores are available in large tonnages in deposits containing 0.2 to 0.3 pct tungsten trioxide . The objective was to achieve a high recovery of the tungsten in concentrates , containing a minimum of 10 pct WO3 , that would be suitable for chemical processing into high- quality synthetic scheelite . The principal problems encountered and resolved by bench- scale flotation tests on ore samples from five different deposits were to define the conditions and reagent combinations essential for ( 1 ) achieving selective flotation of a small amount of scheelite from a large amount of calcite and ( 2 ) controlling the effect of small amounts of calcium , magnesium , and iron salts in the ores and water used . The flotation process was evolved from batch tests and continuous runs in a pilot - scale mill with a capacity of 100 lb per hour . The flotation process comprised ( 1 ) removal of sulfide minerals , ( 2 ) conditioning the residual ore pulp with sodium carbonate , quebracho , and trisodium phosphate , and ( 3 ) rougher flotation and single - stage cleaning of a scheelite concentrate . In a pilot plant run , over 91 pct of the tungsten was recovered from ore containing 0.27 pct WO3 , in a concentrate containing 11.2 pct WO3 .

Jan 1, 1964

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By Kentwell D. J, Cusak C. J, Harvey-Kelly F. E L, M D. Goodz

The Morning Star Gold Mine presents an example of a prolific operation with considerable historical records, mine workings, drill hole logs and countless plans from greater than 20 adjacent mines which have now been consolidated to form the current project. Implementation of 3D computer modelling in the planning stages has provided an additional tool to integrate and refine geological models as a guide to some exploration strategies. It has allowed for a re- interpretation of the host rock units, dimensional constraints, new exploration extensions and provisional resource modelling. The initial consideration of this project was to integrate 135 years of mining history into a single database. Each historic mining area had an unrelated mine grid, often established parallel to the long axis of their main stopes; some were based on magnetic or true north. Survey plans were in chain, imperial or metric units. Through the manipulation and rotation of old grids, previously unrelated mine workings began to form continuous mineralised zones, with unmined portions still remaining in between the existing development. Furthermore the current drillhole database of >433 holes showed numerous confirmatory intersections of new mineralisation. A series of tiered tables were created within a relational database to derive guidelines for assessing data to attribute a Mineral Prospectivity Value [MPV] based on key indicators of mineralisation. Indicator logging now forms the basis of geological descriptions.

Jan 1, 1997

By M. Pearson, L. Zunti

Pressure vessels in hydrometallurgy and many chemical process industries throughout the world require the use of specific lining systems to protect the parent vessel materials from corrosion and/or abrasion. Typically, these lining systems are required for processes that are corrosive and operate at elevated temperatures. Two basic lining system types arc: 1) refractory linings in conjunction with an impervious corrosion resistant membrane, and 2) metal-clad vessels consisting of titanium or other corrosion resistant metal bonded to a carbon steel shell. Operating conditions play a key role in selecting the type of lining system to be utilized for a specific application. Lining systems in turn have an impact on the process vessel size, which ultimately affects the capital cost of the vessel. The capital costs for each type of lining system must be considered for each application, as well as maintenance concerns, quality control, and delivery. It is clear that operating conditions play a key role in the final selection of lining systems utilized for specific projects based on initial capital cost, life-cycle maintenance costs, and overall service life. This paper will examine the fundamentals of each lining system, their inherent technical strengths and weaknesses, and present relative cost comparisons for each lining system as they apply to specific operating conditions and vessel sizes.

Jan 1, 2004