Search Documents

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By Peter T. Luckie

Up until the past couple of years, thermal coal dryers were only used to dry midwest and eastern United States bituminous coals. These dryers were primarily installed at coal preparation plants to freeze proof the coal and lower the transportation costs per BTU. Today thermal coal dryers are being specified to dry western sub-bituminous and lignite coals for these and other reasons brought about by the intense interest in coal gasification and liquefaction. One reason for drying western coals ahead of a coal gasification plant is the elimination of surface moisture which would prevent efficient sizing of the coal, since feed material size consist is very important in most commercial coal gasification processes. Thermal dryers are being proposed for liquefaction processes because of the need for a feed material containing approximately 4% or less total moisture Future coal gasification processes may also need to reduce feed material moisture content.

Jan 1, 1975

By M. G. Atmore

As is usual when preparing for this type of occasion, I looked back at the subjects covered by my predecessors when they assumed the presidency of this Institute. You will appreciate that, in the eighty odd years since the Institute was founded, the diversity of subjects has been very great. In almost all cases it is quite natural that the speaker should have chosen a topic of special interest to him and one in which he was particularly knowledgeable.

Jan 1, 1979

By William D. Hissem

For those blasthole applications which require the use of holes ranging from 1” to 5.5” in diameter, the use of top hammer drills has been the equipment of choice for several generations of drillers. Pneumatic compressed air and hydraulic compressed oil systems represent the primary technologies which are available to the drilling practitioner. While both employ the same operating principals, the characteristics of performance, cost, and reliability can be markedly different between technologies and manufacturers.

Jan 1, 1998

NOTICES The Institution of Mining and Metallurgy The Institution is to hold a one day meeting entitled "Sampling in the mineral and metallurgical processing industries" at Imperial College, London, on 2nd July, 1973. International Conference on Air Pollution This Conference is organised by the Department of Health and the National Association for clean air. Consas 74 The Fifth Conference of Southern African Surveyorswill be held in Salisbury, Rhodesia, from 3rd to 9th February, 1974.

By Smith Bracewell

First evidence of bauxite in Jamaica resulted from an analysis of a soil sample collected at Bull Savannah in 1938 during a systematic local investigation of the island's soil types. Results of subsequent work indicated the possibility of the occurrence of deposits of commercial grade and dimensions, and in 1942, with a view to emergency development of the deposits as a war measure, the Jamaican Government declared all bauxite in the colony to be Crown property.

Jan 10, 1958

By Ed Billington, Mike Shields

The trail blaster is faced with a wide range of workrelated challenges, not the least being the work setting itself. It is usually remote, being anywhere from 5 to 30 or more miles (8 to 50 km) from any road. It may be in mountains, high rock desert, or coastal rain forest, and can range from sea level to over 12,000 feet (3700 m) in elevation. The blaster may be part of a 2-person clearing crew, a 4-person maintenance crew, or a 10-person construction crew. The crew will usually be mobile, moving and working up to 10 miles (16 km) or more per day, relying mostly on their own backpacks to move camp, tools and supplies from site to site. Periodic resupply may be by helicopter, aird rop, or even “sherpa” groups, but most often will be by packstrings of horses and mules. The crew goes into the backcountry a n y w h e re from two weeks to three months at a time, and while there, its members “live the job” 24 hours a day, enjoying baking heat, torrential rain or mid-July s n o w s t o rms along with the truly glorious weather that c o m p e n s a t e s . So who is this blaster? Well, “he” may be she, since some of the top trail blasters are women. He/she will also be more than a blaster: Crews are small, so experienced members must be capable of handling the full range of trail work. Thus this blaster is also a driller, and usually also a bucker, snag faller, rigger, dry-stone mason, log and timber carpenter, bridge builder, mule p a c k e r, small-engine mechanic and, not least, camp cook capable of putting out a hot meal from a campfire , in a downpour, in the dark. Being in remote locations, often without reliable communication to the outside world, trail crews enjoy a remarkable degree of independence from “supervision.” With that comes the responsibility to make sound decisions which expedite the work, while promoting crew safety and welfare .

Jan 1, 2004

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By T Do, J Siliezar, M Larson

With the expansion of magnetite projects in Australia has come the opportunity to take advantage of newer technologies that were not necessarily available when the magnetite industries of North America and Europe were maturing. One of these technologies is the IsaMill, originally developed for the economic treatment of ultra-fine grind (UFG) duties of Mount Isa Mines. As understanding of the IsaMill has increased, so too has the ability to process coarser feeds while maintaining the same energy efficiency advantage and tight product size distribution that originally made the IsaMill so attractive. In the case of magnetite the hard non-elastic ceramic grinding media is ideally suited to the grinding duty when compared to steel grinding media. The centripetal separator and naturally steep product size distribution curve provide a mill discharge that maximises the critical concentrate grade. This paper analyses the effect of the IsaMill grinding technology on the full-scale Ernest Henry Mine (EHM) magnetite operation along with pilot and lab scale demonstrations of optimisation. Issues encountered and the solutions to maximise the mill throughput and quality are examined in an effort to promote better understanding across the industry. CITATION:Larson, M, Do, T and Siliezar, J, 2013. Enhancing magnetite returns - the benefits of IsaMilling, in Proceedings Iron Ore 2013 , pp 411-416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Chris Mark

In the wake of the Crandall Canyon mine disaster, the U.S. Congress asked the National Institute for Occupational Health and Safety (NIOSH) to study the safety of deep cover pillar recovery operations in the US. The legislation defined ?deep cover? to be greater than 1,500 ft, but NIOSH is also evaluating mines at depths greater than 1,000 ft when multiple seam interactions are encountered. By these definitions, there about 35 active mines that engage in deep cover pillar recovery, in the states of UT, CO, VA, WV, and KY. To date, NIOSH has documented ground conditions and ground control experience at nearly all of them. This paper provides an overview of current deep cover pillar recovery practice. Specific ground control issues that are discussed include: Pillar and barrier pillar design, ? Coal bumps, Thick seam pillar extraction, and ? Multiple seam interactions.? INTRODUCTI

Jan 1, 2009

By P. G. Mason

The Getchell property was mined for oxidized gold ore by underground and open pit methods from 1936 to 194.5, by which time known oxide ores were mined out. From 1945 until 1967 sulfide ores were mined and roasted to improve gold recovery with varying degrees of success. In J 983 FRM Minerals, Inc. purchased the property. Since then they have carried out extensive geological exploration to define the size and character of the orebody. The sulfide ore is refractory to direct cyanidation, thus considerable metallurgical testing has been necessary to develop a suitable, cost effective process for its treatment. Wright Engineercs Limited have designed and engineered a gold extraction plant, which incorporates pressure oxidation to liberate the gold and? is scheduled to be commissioned early in 1989.

Jan 1, 1989

By J. G. Dunn, A. S. Ibrado, D. J. Hollbach

Gold production is one the most important mineral process­ing industries in Western Australia. The gold is usually found in either weathered oxidised zones, or associated with sulfides. In the latter case, oxidation is achieved by some form of chemical processing, such as roasting or more recently bacterial leaching. In all cases, gold is dissolved out of the oxidised matrix by cyanide solution. Pyrrhotite is an iron sulfide generally represented by the formula Fe1_,S where O x 0.125. Three different structural forms ofpyrrhotite are known to occur naturally, stoichiometric FeS (troilite), hexagonal pyrrhotite Fe1_xS and monoclinic pyrrhotite Fe7S8 [I]. Substitution of iron atoms within the pyrrhotite structure by other ions of similar atomic radius such as nickel, copper, cobalt and manganese is also possible [2], and often observed in natural pyrrhotite samples. Pyrrhotite is abundant in Western Australian sulfide mineral deposits which are commonly associated with gold bearing ores. It is generally believed that pyrrhotite has a detrimental effect on gold recovery from such ores, as it is commonly claimed to decompose in alkaline, aerated cyanide solutions to form iron cyanide complexes, thus consuming free cyanide, and to form sulfur/oxygen containing species such as sulfate, through oxidation of sulfur in pyrrhotite, which thus consumes oxygen. From information gleaned from the literature, claims about the high reactivity of pyrrhotite in cyanide appear to be based on early cyanidation studies performed on gold ore samples which have been poorly characterised, and contained impurities such as pyrite, arsenopyrite and chalcopyrite, which may have also contributed to the levels of species observed in solution [3-5]. In addition, the investigations do not take into account that iron atoms in the pyrrhotite structure may have been partially substituted by other atoms that influence the solubility of pyrrhotite in cyanide solution.

Jan 1, 1995

By Charles Brush

THE general subject of accurate pyrometry, its great development in recent years, and the importance of its application in arts and manufactures is so ably treated in other papers that this paper will bee confined to a resume of some research work on certain temperature effects in carbon and other steels, some of which appear to, be new. The results of these researches are embodied in several papers presented to' various scientific societies during the last few years, most of them under the general title of Spontaneous Generation of Heat in Recently Hardened Steel.1 Several years ago, when studying the behavior, tinder certain conditions, of specimens of hardened tool steel, I observed that they all spontaneously generated a small quantity of heat, the rate of generation diminishing from day to day for several weeks before generation became imperceptible in the sensitive calorimeter used. In each case the steel had been hardened only a few days prior to its use. It seemed highly probable that the generation of heat was associated with some sort of "seasoning" or incipient annealing process, perhaps accompanied by slight changes of volume, and that it would be most rapid immediately after hardening. I subsequently investigated this curious phenomenon more fully. Twelve ½ in. round bars of tool steel, 5 in. long and with machined surfaces, were hardened by heating to high cherry red in a reducing atmosphere of a gas furnace and quenched in cold water. The bars then had a thin strongly adhering coating of black oxide. They were next stirred in a large quantity of water at room temperature, to acquire that temperature, wiped dry, and oiled with heavy, neutral mineral oil to prevent generation of heat by further surface oxidation, wiped free of excess of oil and placed in the copper cylinder of a heat-insulated box.

Jan 9, 1919

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

By R. A. McClelland

In the development of the Sirosmelt tin smelting process the need has arisen to understand and predict the problems likely to be encountered in optimal furnace operation on larger scales and over wide ranges of operating parameters. To study these parameters in detail with existing pilot plants and production scale plants is prohibitive in terms of cost, time and limitations of furnace design. The Sirosmelt computer model, SMELT, has been developed to simulate the process and to study a range of metallurgical parameters. The model's robust basic form has allowed adaption to a variety of needs. It is now being used to generate data on optimum operating conditions for a commercial scale plant and for operator training.

Jan 1, 1984

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By D. Robert Weir, Roman M. G. S. Berezowsky

Pressure oxidation can virtually always render refractory auriferous sulphidic ores and concentrates amenable to cyanidation. Its effectiveness as a pretreatment of refractory gold feedstocks is reflected by the successful startup and operation, over the past four years, of four commercial plants. At least three more are scheduled to come on stream during the next three years. Over the past eight years, a variety of ores and concentrates have been subjected to integrated miniplant testing and process demonstration by Sherritt, and data derived from these studies have been used in the design and construction of several of the commercial facilities. Some factors affecting the selection of pressure oxidation in gold recovery processing are discussed.

Jan 1, 1989

By James F. ` King

This paper reviews the changes which have taken place in the supply of smelter-grade alumina and refinery-grade bauxite over the past twenty years. It highlights the current situation and identifies some trends which are to be expected in the medium- and longer-term future.

Jan 1, 1986

By Geraldine Woods

I work for the State of Washington as an Explosives inspector. My paper will describe the mission of the Wa. State Dept. of Labor pertaining to explosives and the regulation of explosives in the State.Blasting safety is high on the public safety list and the regulation of explosive use and storage has been mandated through legislature. The Dept. considers pro-active partnering forexplosive safety preferable to after-the-fact citations for non-compliance.In some cases, the Dept. will issue civil citations with monetary penalties, meant to be a deterrant, of course, to blasters who choose not to comply with the explosive regulations of the State.The Dept. has also revoked and suspended blasting licenses. In some instances, the Dept. has allowed recipients of citations with monetary penalties to reduce the amount paid by attending technical training classes. The idea here, is to reduce the chance of reoccurence of unsafe blasting practices. The State of Washington partners with MSHA in the regulation of explosives use and storage in mines, pits and quarries in the Stateas well as working closely with law enforcement, State and local fire marshals, ATF,and is active in ISEE in part of it’s ongoing effort to promote explosive safety and establish communications in a nonadversarial way with explosives users. My paper will include some statistics on licensing in the State, pounds of explosives used, inspection numbers, numbers and types of complaints with information from the inspections resulting of these complaints. My paper will include examples of storage, both good and bad, examples and pictures of fly rock incidents, accidents, near-miss close calls, break-ins, thefts, and abandoned explosives. This paper may also include a brief summary of my opinion of explosive regulation and my job as a regulator, including examples of high and low points of the job, joys and frustrations.

Jan 1, 2002