Search Documents

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By Yesil MM, Bozdag T

The swelling process is an impor- tant problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from oedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the oedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Liu C. H, Juang Y. F

Coal/gas outbursts were one of the rather difficult safety problems faced in the coal mines of this Country, with coal fields characterized by frequent disturbances of folds, faults and pinch-offs. With average mining depth about 500m below surface, several such accidents occurred with up to 500 tonnes of coal outburst. In recent years, after a series of improving countermeasures had been undertaken, gas outburst accidents had been greatly decreased. The characteristics of gas outbursts in Taiwan coal mines include relating to coal petrography, mining depth and the other deformation forces. All these have been investigated, trying to determine the parameter of outbursts under natural conditions. The preventive countermeasures include predicting tests, de-stressing boring in coal seams, the emergency procedures during outbursts and certain improving options.

Jan 1, 1988

Alternative processes for converting coal to liquid products and their stage of development are outlined. The merits of hydrogenationprocesses in general, and the solvent refined coal process in particular, are stressed. Bench scale experimental hydrogenation procedures used by the Australian Coal Industry Research Laboratories Ltd. (ACIRL) to study the liquefaction of Australian coals and correlations between properties of such coals and their conversion to liquid products are described. Factors involved in assessing investment and operating costs for modern hydrogenation based coal refineries of different capacities are described with reference to a recent study undertaken in N.S.W. The significance of coal properties such as yield and yield structure of total liquid products and how they and other factors can influence the economics of the coal refining operations are discussed.

Jan 1, 1977

Capture airborne coal dust generated by a continuous mining machine to reduce workers? dust exposure and to improve face visibility. Approach Develop a low-profile dust collector system which can be mounted on the boom of a continuous miner. How It Works When coal is mined with a milling head continuous miner, a substantial amount of coal dust (respirable and non-respirable) escapes the dust suppression sprays at the cutter head. This can cause poor visibility around the cutting head and can expose the workers to high levels of respirable dust. A practical means of removing this dust is with a scrubber mounted directly on the mining machine. Under a Bureau of Mines contract, a low-profile, machine-mounted dust collector (MMDC) was developed to avoid adding extra height to the continuous

Jan 1, 1983

By D. G. Kesterke

Research was conducted to determine the feasibility of extracting elemental oxygen from silicate-bearing melts by high-temperature electrolysis. The method was based on a modification of existing processes for electrowinning metals from their oxides dissolved in molten halide systems. Electrolyses were performed at temperatures ranging from 1,050° to 1,250° C in boron nitride cells that incorporated a silicon carbide cathode and an iridium anode. The electrolytes contained volcanic scoria as the oxygen source, plus mixtures of BaF2 and LiF as fluxing agents. Cell gases containing almost 14 volume-percent oxygen were obtained. The average anode current efficiency for several experiments of extended duration was calculated to be 55 percent. Cell design and operating conditions are described, and some of the problems associated with the process are discussed.

Jan 1, 1971

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By Terlich R. E, Finlayson J. M

A combination of high virgin rock temperatures, deep workings and extensive utilisation of heavy diesel equipment has presented North Mine (A Division of North Broken Hill Limited) with challenging ventilation problems. These problems have been addressed in a variety of ways which include in the order of 6000 kM of underground refrigeration. The future of North Mine depends on the successful development and extraction of ore in excess of 1100 m below the shaft collar using mechanised cut and fill mining. The success of this will depend on the installation of a complex chilled water reticulation circuit in this area. This will involve planning and constriction of a number of large dams, installation of pups and turbines, and the successful commissioning of several large water to air heat exchangers.

Jan 1, 1988

By Fathi Habashi

IT APPEARS that the phenomenon of ion exchange by which saline water was converted to sweet was known to Moses and Aristotle. However, the credit for the recognition of this process is generally attributed to Thompson (1850) and Way (1850), who reported that when a soil was treated with either ammonium sulfate or ammonium carbonate solution, most of the ammonia was adsorbed and calcium was released. It was later proved by Eichorn (1858) that the adsorption of ions from ground waters by clay constituents was a reversible process. The first attempts to utilize ion exchange phenomena was in the field of water softening around 1906, using natural and synthetic silicates. In 1935 Adams and Holmes in England observed that crushed phonograph records (phenol-formaldehyde and amine-formaldehyde resins) were capable of exchanging ions.

Jan 1, 1970

By Herbert Clark Hoover, Lou Henry Hoover

MANY persons hold the opinion that the metal industries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requiring not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. For a miner must have the greatest skill in his work, that he may know first of all what mountain or hill, what valley or plain, can be prospected most profitably, or what he should leave alone ; moreover, he must understand the veins, stringers1 and seams in the rocks2. Then he must be thoroughly familiar with the many and varied species of earths, juices3, gems, stones, marbles, rocks, metals, and compounds4. He must also have a

Jan 1, 1950

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990

By Oliver R

The Hamersley Iron ore resources are geologically complex with fluctuations in mineral chemistry. From this resource Hamersley Iron must produce consistently high quality direct shipping products and have the ability to evaluate the effects of changes in demand. In order to achieve these objectives an incremental long term planning technique has been developed. This method reduces the total geological resource statement into a simple, logical sequence of events. A logical sequence of mining increments is defined within individual areas based on a final pit and access system. Increment characteristics are derived manually and from a computer based orebody model. The end product of the technique, an optimum mining schedule, is readily developed from the incremental information. Among its many benefits, this simple technique rapidly provides management with information for policy formulation.

Jan 1, 1979

By Henning Nielsen

SIX weeks ahead of schedule, the International Nickel Co. of Canada Ltd. has brought a 30-mile rail line into the newly born town of Thompson, Manitoba. Its construction spurs the development of a rich new mining region slated to become the world's second largest nickel-producing area-exceeded only by Inco's Sudbury, Ont., workings. Two mines, the Thompson and the Moak Lake, will be opened to meet International Nickel's scheduled annual production goal of 385 million lb of refined nickel by 1961. Accomplishment of this aim will mean an additional 75 million lb of the metal available to consumers. In addition, stepped-up out- put of Inco's Sudbury holdings may increase this figure by another 25 million lb. (For an earlier report on these developments see MINING ENGINEERING News, January 1957).

Jan 12, 1957