Search Documents

The article presents methods of testing and recording of water amount pumped out in surface mining. The authors describe necessary recommendations how to carry out measurements so that one can separate the surface run-off and groundwater inflow from the total inflow. They demonstrate methods of evaluation of these kinds of inflow in open pits when water amount testing is carried out every eight and 24 hours as well as simple methods when only monthly records of water are available. The authors also describe procedures for evaluating the water inflow when an open pit is dewatered gravitationally and measurements in discharge channels are irregularly carried out.

Jan 1, 2003

By David D. Gallagher, Edmond J. O’Donovan

It has been well accepted for many decades that hard starting of conveyors has associated problems. It is particularity damaging to the belt and splices. Recent measurements of hard starts on a long conveyor with a low modulus belt showed very unusual responses. These included violent accelerations and repeated "whip cracking" of the belt. Laboratory investigations of the very high strain rates experienced by the belt during the whip cracking, show mechanisms for belt damage that are not associated with normal usage. This paper outlines the measurement to show that for long, low modulus conveyors, constant torque controls are inappropriate and time ramp controls are really essential.

Jan 1, 1998

By Daniel L. Hanson

This paper presents case histories of the construction of four large diameter circular shafts using reinforced concrete ring beams as the primary internal support system. The case histories pertain to concrete ring beam systems which have been successfully used in shafts up to 130 feet in diameter and 75 feet deep. Soldier pile and lagging, and driven steel piling earth retaining systems using ring beams, are discussed together with the cost savings associated with using concrete ring beams. Soil conditions encountered at the case history sites are discussed together with the development of design criteria for each shaft. Instrumentation data obtained at one site are also presented.

Jan 1, 1987

By R. W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from nonkimberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques where spectral bands are chosen to optimize contrast between the kimberlitic soils, nonkimberlitic soils, and vegetation. Careful processing of the multispectral data is essential to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1986

By T. H. Dubaniewicz, J. E. Chilton

The U. S. Bureau of Mines is investigating the application of fiber optic technology to methane and carbon monoxide monitoring. A methane monitoring system is described that is based on differential absorption of infrared light. It can detect concentrations as low as 0.2% and as far away as 2 km via fiber optic cable. The upper range is 100% methane. The system requires no electrical power within the mine so it should operate safely under mine disaster conditions. A hybrid carbon monoxide monitoring system is described that combines a low-powered electrochemical cell with fiber optic telemetry. Testing has shown the system can operate maintenance- free for several months.

Jan 1, 1992

During the post war era, the requirements of the "Third" World for modern civil works, energy and industry, coupled with an insistence that these capital installations are understood and controlled by indigenous people, have crea- ted a demand and flow of technology from those countries with well developed skills. Thus has grown a real trade in technology - an activity in which consultants play an important role. An indication of the magnitude of this trade is given, together with an outline of some of the special problems. Australia is shown to be dis- advantaged and has been slow to offer the incen- tives to consultants which other countries offer.

Jan 1, 1975

By T. M. Yegulalp

This article summarizes some of the results of the continuing research activity at the Henry Krumb Schools of Mines, Columbia University, directed towards a better understanding of the stochastic behavior of slurry flows in underground coal-slurry pipeline systems. Fundamental ideas supported by field observations are presented and a Semi-Markov model of the slurry flows is developed. As a result of this formulation, behavior of combined slurry flows from N independent coal faces can be expressed in analytical form. The contents of a slurry surge tank receiving slurry flows with certain stochastic characteristics is investigated in a function of discharge pump characteristics and time.

Jan 1, 1983

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By Song Xiaotian

In this paper the enviroment in which Tong Kuang Yu mine, China is developed is described. Geological and geomechanical environments which pose difficulties in the design and optimization of Block Caving are discussed. According to mine conditions, caving process simulation was carried out using Displacement Discontinuty Method and relationships between stress distribution .and undercut parameters were established in accordance with different undercut sequence. Based on simulation the influences of caving parameters on caving probability, drift instability and ore-draw control were analysed in order to optimize Block Caving Mining. On the basis of simulation and mathematical programming, the optimal sequence is proposed essential to satisfy the safety, production and other restrictions.

Jan 1, 1989

By Maynard O. Serbousek, James R. McVey

IS there a quick way of assessing the conditions of a newly exposed roof in a coal mine? This has always been a nagging question. The problem is that unless effective controls are established as soon as possible, it becomes extremely difficult to extract coal safely and economically from conventional underground milling operations. Until recently, little has been done to provide a means of measuring the structural behavior of a coal mine roof while the face advances during actual production. (In fact, most measurements have always been made after the fact or during a roof pull-down where the roof is actually caused to fail with no support.)

Jan 9, 1976

By Alan C. Noble

INTRODUCTION Forecasting of metal and mineral prices is a complex and hazardous undertaking. In order to accurately forecast prices, the complexities of both marketing and production must be modeled for each commodity. Even with the most detailed model, the economy may change unexpectedly, invalidating the forecast. Because of these factors, this chapter will not attempt to present specific methods for price estimation. It will, however, review the fundamentals of price forecasting as applied to planning and design of the final pit shell. Recognizing that no price estimate can be exact, sensitivity analysis will be reviewed as an approach to coping with these unknown variations.

Jan 1, 1979

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products. The original source of potassium was wood ash, however, today the term potash refers to all commercially important salts of potassium. The world's first potash mining operation commenced in Strassfurt, Germany, circa 1860, and since that time the industry has grown steadily to its present annual output of about 30 million tons of potassium chloride products or 18 million tons of Kg0 equivalent, potassium chloride or "muriate of potash" being equivalent to 63.1 % pure KPO.

Jan 5, 1972

By Robert P. Edwards, Brian C. Flintoff

Crushing plants (multiple stage) are an integral part of most conventional comminution circuits (ball mill, rod mill - ball mill). Although conventional circuitry is now the design exception, there are still many older, and some newer plants that include crushing in the process flowsheet. In most of these installations the operating objective is to maximize throughput at some minimum product size, in an effort to balance the comminution load between crushing and grinding. To achieve this goal, while avoiding production losses due to overloads, generally requires the use of automatic control strategies. This paper reviews the crushing plant control problem and describes several approaches that have been successfully implemented in different plants.

Jan 1, 1992

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By W. N. Marchant, P. T. Brooks, P. B. Altringer, R. O. Dannenberg

The US Department of the Interior, Bureau of Mines conducted laboratory tests to devise a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 ppm W (70 ppm W03). Using ion exchange resins synthesized by USBM chemists, 98% oft he tungsten was extracted from the brine and 92% of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44% tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process research unit to provide more reliable data for an economic appraisal.

Jan 8, 1979

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions.

Jan 6, 1978

By Youning Li, William J. Drury, Christopher H. Gammons

A demonstration scale, subsurface flow anaerobic wetland was built to treat zinc and other metals in surface drainage near the historic mining center of Butte, MT. Based on three years of continuous monitoring (1996-1998), copper and cadmium were effectively removed year-round, but attenuation of dissolved zinc was dependent on hydraulic residence time (HRT) and bacterial sulfate reduction (BSR) rates. BSR rates decreased in winter months, as did HRT due to the development of thick frost zones in the substrates. An additional problem was the inability of the wetland substrate to completely filter out fine-grained particles of ZnS forming in the anaerobic cells.

Jan 1, 2000

By Robert Irvine

Exploration activity for diamonds in Canada has recently experienced a dramatic increase. Disclosure of a diamond discovery exhibiting features of a potentially economic deposit contained in a kimberlite pipe in the Lac de Gras area of Canada's Northwest Territories has sparked substantial interest in-Canada and abroad and has triggered the largest staking rush in terms of area in the history of Canadian exploration. In this paper, we report on the nature and extent of current exploration activity in Canada for diamonds (with special attention to Arctic regions), the results of this activity to date, and the context in terms of current world markets for diamonds.

Jan 1, 1995

Terminology Relating to Nonmetallic Elements in Metals. See IRON AND STEEL Ferromagnetism in Metallic Crystals. BY L W MCKEEHAN (Tech. Pub 554, Metals Tech , August; also Trans, vol 111. 20,500 words ) The directions for easiest magnetization of ferromagnetic single crystals are those of simple crystal- lographic forms and the extra energy needed for magnetization in other than these preferred directions depends upon the material selected for test The history of magnetic tests upon metallic single crystals, reviewed in detail, shows that crystals of one metal agree rather well as to the magnitude of such energy differences. This makes ~t probable that these differences are really charactenstic of the ferromagnetic

Jan 1, 1935