Search Documents

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961

By John D. Spencer

Clean energy production from coal, oil, and gas, and the development of these and other energy sources continued to be a major objective of the energy research program of the Bureau of Mines.3 In 1971 increased emphasis was placed on the production of fluid fuels and chemicals from coal. Advances were achieved in the development of the Synthane and Hydrane gasification processes for producing pipeline gas from coal (page 31), and progress was made in research on solid wastes utilization (page 2), and on liquid fuels production from coal (page 37); Coal mine safety, solid waste disposal and utilization, coal preparation and transport, and fundamental research on coal and related products also continued to be the subject of extensive research. Improved methods for extracting petroleum and natural gas without surface and subsurface pollution featured research on these vital fuel and energy sources. This research was highlighted by studies of the fracturing systems of reservoir rocks, including subsurface fracture mapping and new fracturing techniques to achieve optimum production of oil and gas (page 52). Of equal importance were projects on oil recovery by water or gas flooding (page 52), by steam injection (page 57), on the identification of oil spills (page 63), and on means to reduce vehicular exhaust emissions (page 66).

Jan 1, 1972

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989

By Russell Barr

Operational excellence is generally known as a management system integrated across critical functions that is geared towards continually improving operational performance. Functional areas such as health, environment and safety, quality and human resources are the focus of many corporate-wide operational excellence programs. Operational excellence also focuses on improving areas such as customer orientation, employee empowerment as well as process, and systems optimization. It is widely viewed as critical to sustaining business performance improvement. Although it is difficult to find a universally accepted definition, or even common foundation in many respects, operational excellence remains a popular term in the business world. Many organizations have developed their own version of organization excellence, influenced by such individual factors, other similar institutions or even third-party service providers. A mining organization is no different from other organizations in that adopting and implementing effective operational excellence programs can dramatically improve business execution and performance across regional or global interests. This paper brings together various perspectives of operational excellence and reconciles them for a useful composite for the mining industry. While most agree that operational excellence should include normal functions in a manufacturing operation such as production, maintenance and engineering and processes such as quality, environmental and continuous improvement, many other factors for operational excellence seem to vary from perspective to perspective. Thus, programs that manufacturers engage in may seem the same, but may, in fact, be different in key areas. This may affect organizational performance in tangible ways. Management must buy into the company?s definition of operational excellence and be dedicated to achieving it. A review of many of the existing definitions of operational excellence, explicit or embedded as part of a program, seems to yield the following common factors: ? It should help organizations better execute their processes and services. ? It should be geared towards improving quality ? It requires that the various operations should be aligned with the overall enterprise strategy. ? It should be geared towards continuous improvement. A composite of operational excellence definitions suggest that it is: ? Geared towards helping the organization achieve sustained profitability; ? tied to strategic alignment and business objectives; ? tied to solid investment strategies; ? integrated as part of the culture, process, time plan and performance; ? a relevant performance measurement system; ? extended to include all aspects of the supply chain (including external suppliers); ? integrated with health, safety and environmental (HSE) aspects. And, while the pursuit of operational excellence intuitively suggests that businesses should improve, it is very difficult to achieve given the difficult challenges facing companies today. Mining businesses face numerous pressures to perform in a global marketplace such as demand, energy cost, variable cost and pricing fluctuations as well as infrastructure challenges to further confound the environment. Companies generally must look to the following:

Jan 1, 2009

By H. Rosenthal, A. L. Jamieson

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

There are many different challenges when sampling mineral commodities. Sampling is part of many decision-making processes, from control of the number of drops of a reagent to all aspects involved in determining how much to pay for a mineral consignment. However, if all decisions must be supported by correct assumptions, or at least agreed terms, how can this be guaranteed? The main approach is to emphasise the importance of continuous surveying of sampling practices. If they are based on non-recommended protocols, this raises concerns. In addition, safety failures and lack of appropriate behaviour from the technical perspective can lead to disasters, both from the human and business perspectives. Impacts on safety and health are clearly unacceptable. It should be noted that imperfect safety and health practices in sampling operations have a strange correlation with incorrect sampling techniques. The commercial interface can also be affected. Companies have studied extensively the various aspects of measuring quality parameters for mineral commodities to understand the risks for investors and owners, and they take decisions that fundamentally respect the interests of parties in contracts and not result in losses. Every result should be obtained in defensible ways, and neither losses nor profits taken in indefensible ways. Most of such situations are related to bias; a significant systematic difference between a measured value and a reference value for a contractual quality parameter. Bias is always undesirable, because it always implies an incorrect advantage for one party and without doubt an undesired disadvantage for the other party. These situations are solved financially through a third-party arbitrator becoming involved in delicate situations, such as a commercial claim, but the outcome is always tangibly or intangibly bad for one of the parties. Another possibility is a permanent or temporary loss of precision. Poor precision, due its nature, generates reasonably balanced losses and profits, but it may hide out-of-control situations, generate instability and induce financial losses due to actions taken towards clearing commercial disputes involving interlaboratory programs, sample exchanges and duplicated sampling and sample preparation procedures, in the end wasting time and resources and creating a permanent source of commercial tension. While bias situations demand immediate adjustments for correctness, poor precision has to be understood as something that cannot be just calibrated out and is a situation that demands investment of time and effort. Precision optimisation has to take into account best practice for obtaining the required precision as well as cost/benefit analysis studies. Purchasers, engineers, salesmen and all personnel need to recognise that sampling is a major area to understand when taking decisions. The aim is to spread concepts that can really help, such as simple in-house actions to improve productivity and completion of surveys on commercial sampling operations, in order to ensure correct results are obtained and assertively take corrective actions, thereby establishing a healthy relationship with investors, suppliers and purchasers and in the process optimising the business.

Jan 1, 2008

1. Reviews Steel and its heat treatment, by K-E Thelning. 2nd Edition. London, Buterworths, 1984.678 pp. R201,60 (incl. OS1). Reviewer: J.P. Hofman The Southern Queensland Conference 1985. Parkvile (Australia), The Australasian Institute of Mining and Metallurgy, 1986. A$ 15.00. Reviewer: R.B. McGilivray Rock mechanics, by A.R. Jumikis. 2nd edition. Clausthal-Zelerfeld (West Germany), Trans Tech Publications, 1983. US$ 58. Reviewer: R.W.O. Kersten The XVIth International Coloquium on Refractories. Freiburg, West Germany, 1985. DM 80. Reviewer: H.J. S. Kriek Diamond driling handbook, byW.F. Heinz. Johannesburg, South African Driling Association, 1985. 517 pp. R30. Reviewer: S.A.G. Martins Processing and utilization of high sulfur coals, edited by Y.A. Atia. Amsterdam, Elsevier, 1985.788 pp. Oft. 385. Reviewer: L.M. Falcon Weighingand proportioning of bulk solids, by Hendrik Colijn. 2nd edition. Rockport (U.S.A.), Trans Tech Publications, 1983. 398 pp. $60.00. Reviewer: G. Cunningham Investment appraisal and economic evaluation of mining enterprise, by S. von Wahl. Clausthal-Zelerfield (West Germany), Trans Tech Publications, 1986. US$ 40. Flotation of sulphide minerals, edited by K.S. Eric Forssberg. NewYork, Elsevier Science Publishers, 1985. 480 pp. US$1O1.75. Reviewer: T.R. Twidle 5th Meeting of the European Clay Groups (5th Euroc/ay Meeting), Prague, edited by J. Konta. Praha (Prague), Univerzita Karlova, 1985. Reviewer: D. Bibmann 2. Recent publications CSIRO. Research review1982-84: CS/Ra Division of Mineral Engineering. Melbourne, Commonwealth Scientific and Industrial Research Organization, 1985. 77 pp. The world copper market: structure and econometric model, by Gerhard Wagenhals. Berlin, Springer- Verlag, 1984. 202 pp. DM 37,00.Materials data of high-strength aluminium aloysfor durability evaluation of structures, edited by L. Schwarmann. Disseldorf (West Germany), Aluminium- Verlag GmbH, 1985. BRITISH GEOLOGICAL SURVEY. UnitedKingdom mineral statistics 1985, compiled by H.c. Squirel, A. Jones, N.E. Sharp, M. Lowe, and D. Slater. Keyworth (U.K.), the Survey, 1986. 175 pp.3. Mintek reports Report Ml66D The effect of calcining on the recovery of gold in a sand residue. (1st issued Sep. 1984.) Report M168D The treatment of Uitkomst concentrate. (1st issued Oct. 1984; reissued Mar. 1986.) Report M175D Supergene alteration at the Pering zinc-lead deposit: The nature and extent of the oxidation zone. (1st issued Oct. 1984.) Report M176D Bench-scale tests on the extraction of cobalt and nickel from COMAT leach liquors. (1st issued Nov. 1984; reissued Mar. 1986.)Report M241 PLA TO at Mintek. Report M243 The performance and wear characteristics of grinding media as affected by metallurgical and dimensional factors. Project development The Second Project Development Symposium on Planning, Construction and Commissioning will be held in Sydney, Australia, from 7th to 10th October, 1986. Hosted by the Sydney Branch of The Australasian Institute

Jan 1, 1986

By C. D. Rugen

GROUND raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grindability characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. CHARACTER OF GROUND RAW MIX (KILN FEED) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size, whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1945

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By Wallace W. Key

Chalk is a natural calcium carbonate occurring as the remains of soft, friable, minute marine organisms. Whiting can be either finely ground calcium carbonate prepared from chalk, marble, or limestone or the product obtained by chemical precipitation from a solution or suspension containing lime. Until relatively recently, whiting made from limestone was termed "whiting substitute," but it is now usually designated as limestone whiting. Precipitated calcium carbonate, sometimes called "precipitated whiting" or "precipitated chalk," is a finely divided calcium carbonate product obtained by chemical precipitation from a solution or suspension containing lime. Considerable quantities of precipitated calcium carbonates are produced from many chemical processes. Naturally occurring calcium carbonate in a variety of crystalline forms and in all degrees of chemical purity forms a substantial part of the earth's crust. Exactly where a chalk grades into a marl or calcareous shale through increase of clay or silt or into a hard limestone through consolidation and crystallization is difficult to determine because no rigid specifications have been promulgated for classifying them. Composition and Properties Once considered to be amorphous, chalk was later found to be cryptocrystalline. In the pure state it consists entirely of CaCO3, but many deposits are impure. When impurities are removed and the material is reduced to a finely divided state, it is known as chalk whiting. Much confusion attends the use of the term "chalk" as well as the classification of whiting materials. For instance, blackboard chalk is not necessarily chalk but is sometimes plaster of paris or a form of talc. Colored "chalks" may be true chalk colored and compressed with a binder but are probably such materials as hematite, clays, or carbonaceous matter. The term whiting was applied exclusively to the product derived from true chalk before World War I. Chalk imports were difficult to acquire during World War I, and whiting substitutes, a term applied to the products derived from natural rock deposits and precipitated calcium carbonate, were introduced. Substitute whitings were not acceptable at first, but it was found that blending true chalk with substitutes often created an improved product; eventually by selection of limestone and finer grinding, products not only acceptable, but for some uses superior to chalk whiting, were developed. Gradually the term "substitute" was dropped because chalk whiting had lost its importance, being largely supplanted in the United States by other whiting materials. Whiting is now made in ever-increasing quantities from limestone, marble, dolomite, marls, vein calcite, oyster-shell, as well as primary and byproduct precipitated calcium carbonates. Distribution of Chalk Europe-In England, France, Belgium, Denmark, and other European countries highpurity chalk occurs in extensive beds. The Cretaceous period, or the "age of chalk," in geologic history receives its name from the great deposits of chalk exposed on either side of the English Channel. It has been estimated that oceans in which chalk and allied deposits were formed covered more than 500,000 square

Jan 1, 1960

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, 'iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other *producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since her particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely he kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1948

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably her product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too he, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater dificulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1947

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably her product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too he, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater dificulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1947

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, 'iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other *producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since her particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely he kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1948

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.'," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young's modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith's well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By James D. Bliss, David M. Sutphin

"On the basis of differences derived from genetic, descriptive, and grade-tonnage data, graphite deposits are classified here into three deposit types: disseminated flake, amorphous (microcrystalline), or graphite veins. Descriptive models have been constructed for each of these deposit types, and grade-tonnage models are constructed for disseminated flake and amorphous deposit types. Grade and tonnage data are used also to construct grade-tonnage models that assist in predicting the size and grade of undiscovered graphite deposits. The median tonnage and carbon grade of disseminated flake deposits are 240 000 tonnes and 9% carbon and for amorphous deposits, 130 000 tonnes and 40% carbon. The differences in grade between disseminated flake and amorphous deposit types are statistically significant, whereas the differences in amount of contained carbon are not .IntroductionIndustrial minerals, including mineral construction materials such as sand, gravel, and crushed stone, have historically exceeded metals in global production value. Today, industrial minerals are being used in new and sophisticated ways in response to the late 1980s emerging information- and service-based economies' requirements for less metal and more industrial minerals . Natural graphite is an example of one such mine ral that has been known since ancient times, and is now finding new applications. Graphite was first used as an industrial mineral in Bavaria in 1400 A.D. where it was an important component of crucibles. Traditionally, natural graphite has been used in heavy industries. New applications, such as development of carbon-magnesite bricks a decade ago and the current advancement of alumina/graphite refractories, are increasing its graphite use. Other new uses for natural graphite, such as the use of graphite powder as a thermal blanket for the continuous casting o f steel (Northern Miner, 1987) and the addition of expanded graphite to polyurethane foam where it acts as a flame retardant (Industrial Minerals, 1987), are increasing the demand for this mineral. To meet future demand for graphite and other industrial minerals, knowledge of the characteristics of the deposit types in which they are found is important. A further look at the deposit types for graphite and at construction of descriptive and grade-tonnage models is warranted .The graphite industry recognizes three basic types of graphite , distinguished primarily on the basis of grain size: crystalline flake, lump and chip, and amorphous. These naturally occurring forms of graphite are products of metamorphism and are found in schists of various types, gneisses, and marbles. Temperatures of at [east 400°C are thought to be required for graphite formation (Landis, 1971). Synthetic graphite, also known as artificial or manufactured graphite, is a man-made carbon product and offers higher purity and lower crystallinity than natural graphite. Several authors have written about graphite's unique physical and chemical properties and the uses for individual types of graphite (Krauss et 01., 1988; Graffin, 1983; and Harben and Bate s, 1984)."

Jan 1, 1990

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981