Search Documents

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By A. Rejeb

ABSTRACT: This paper contributes to the study of underground structures in argillaceous media, especially Tournemire argillites (Aveyron, France). The basic results obtained over six years in two experimental drifts at the Tournemire site are presented. In situ measurements cover drift wall temperature, humidity and convergence. Delayed convergence represents around 50-65% of the total measured convergence. Analysis of the measurements has shown that delayed convergence is explained by the viscoplastic behaviour of the argillaceous formations. Lemaitre’s rheological model has been extended to the orthotropic case, as Tournemire argillite is naturally anisotropic. The triaxial creep test results on samples at different orientations enabled the parameters of the Tournemire argillite to be identified in terms of orthotropic viscoplastic law. A plane deformation model, using this rheological law and the initial stress field in the site, was developed to interpret the convergence measurements in the drifts. The computed results match the measurements well, especially during the excavation phase. KEY WORDS: Argillite, convergence, time-dependent behaviour, creep, viscoplasticity, modelling. ZUSAMMENFASSUNG: Der vorliegende Artikel ist ein Beitrag zur Untersuchung der unterirdischen Strukturen tonhaltiger Milieus, insbesondere der Tongesteine von Tournemire (Aveyron, Frankreich). Die wichtigsten Ergebnisse, die in zwei Forschungsstrecken am Standort Tournemine über einen Beobachtungszeitraum von sechs Jahren zusammengetragen wurden, werden hier vorgestellt. Gemessen wurden in situ Temperatur, Feuchtigkeit und Streckenkonvergenz. Von der insgesamt gemessenen Konvergenz sind etwa 50 bis 65 % auf zeitlich verzögerte Konvergenz zurückzuführen. Die Auswertung aller Messungen hat ergeben, dass die zeitverzögerte Konvergenz mit dem viskos-plastischen Verhalten des Tonsteinmassivs zu erklären ist. Aufgrund der naturgemäßen Anisotropie des Tongesteins von Tournemine wurde das rheologische Modell von Lemaitre auf den orthotropen Fall ausgedehnt. Triaxiale Kriechversuche bei jeweils unterschiedlicher Ausrichtung dienten der Ermittlung der einzelnen Parameter des orthotropen, viskos-plastischen Gesetzes. Zur Auswertung der Konvergenzmessungen innerhalb der beiden Strecken wurde unter Beachtung dieses rheologischen Modells sowie des ursprünglichen Spannungszustands vor Ort ein flächiges Deformationsmodell entwickelt. Die Rechenergebnisse zeigen eine gute Übereinstimmung mit den Messungen, insbesondere während der Vortriebsphase. SCHLÜSSELWÖRTER: Tongestein, Konvergenz, zeitlich verzögertes Verhalten, Kriechen, Viskoplastizität, Modellbildung. RESUME : Cet article est une contribution à l’étude des structures souterraines dans les milieux argileux, notamment les argilites de Tournemire (Aveyron, France). Les principaux résultats obtenus pendant six années, dans deux galeries d’expérimentation au site de Tournemire, sont présentés. Ces mesures portent sur la température, l’humidité et la convergence des parements des galeries. La convergence différée représente environ 50 à 65% de la convergence totale mesurée. L’analyse de l’ensemble des mesures a montré que la convergence différée est interprétée par le comportement viscoplastique du massif argileux. Etant donné que l’argilite de Tournemire est naturellement anisotrope, le modèle rhéologique de Lemaitre a été étendu au cas orthotrope. Les résultats des essais de fluage triaxial, sur des échantillons à différentes orientations, ont permis de déterminer les paramètres de la loi viscoplastique orthotrope. Un modèle en déformation plane, utilisant cette loi rhéologique et l’état de contrainte initiale dans le site, a été développé en vue d’interpréter les mesures de convergence dans les galeries. Les résultats des calculs sont en bon accord avec les mesures et plus particulièrement durant la phase de creusement. MOTS-CLEFS : argilite, convergence, comportement différé, fluage, viscoplasticité, modélisation.

Jan 1, 2003

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By N. A. Beier, R. Amos, Smith. L., C. Atherton, D. R. Barsi, D. Blowes, D. C. Sego

"Waste rock is one of the most abundant materials at mine sites and must be properly characterized and managed to limit acid rock drainage and other harmful byproducts. An experimental waste rock pile—part of the test piles research program—located at the Diavik diamond mine (Northwest Territories, Canada) was deconstructed and sampled to study the spatial variability of material properties. Bulk samples were classified based on the amount of material finer than 4.75 mm. Hydraulic properties of each sample were estimated and particle size distribution analysis was completed. These datasets and classification methods might be used to improve the understanding of hydraulic and geochemical behaviour of the material and to study waste rock at other sites. ¦ KEYWORDS Acid rock drainage (ARD), Material classification, Particle size distribution (PSD), Waste rock RÉSUMÉ Les stériles font partie des matériaux les plus abondants sur les sites miniers et, en tant que tels, doivent être correctement caractérisés et gérés afin de limiter le drainage rocheux acide (DRA) et la pré¬sence d’autres sous-produits nocifs. Dans le cadre du programme Test Piles Research Program, un amas de roches stériles expérimental situé à la mine de diamant Diavik (Territoires du Nord-Ouest, Canada) a été décomposé et mis à l’essai afin d’étudier la variabilité spatiale des propriétés des matériaux. Les échan¬tillons en vrac ont été classés en fonction de la quantité de matériaux plus fins que 4,75 mm. Les propriétés hydrauliques de chaque échantillon ont été estimées et l’analyse de la composition granulométrique effectuée. Ces ensembles de données et méthodes de classement serviront à mieux comprendre le com¬portement hydraulique et géochimique du matériau et à étudier les stériles sur d’autres sites. ¦ MOTS CLÉS classement des matériaux, composition granulométrique, drainage rocheux acide (DRA), stérilesINTRODUCTION Statement of problem The characterization of mine waste rock remains a challenge in active mining sites. The large volume of material and the large size of particles make it difficult to collect representative samples. Sampling techniques are often dis-ruptive to mining operations because they alter the structure of the waste rock pile or interfere with mine traffic. The convention at most mine sites to collect little to no information on waste rock material means that models and predictions of how waste material will behave and interact with the surrounding environment are based on general information that might not be site specific. This could lead to environmental damage or higher costs if environmental effects are underestimated during the construction of waste rock structures."

Jan 1, 2019

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-adsorbed onto clay surfaces or inner layers, or organically bound. Rare earth minerals such as monazite exist in coal and have grain sizes smaller than 5 µm. In this study, froth flotation was successful in concentrating rare earth minerals existing in a thickener underflow material derived from Fire Clay seam coal that contained around 431 ppm of total rare earth elements (TREE) on a dry ash basis. Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2,300 ppm TREE. Using a laboratory flotation column to limit hydraulic entrainment, the TREE content was further enriched to around 4,700 ppm, which equated to an enrichment ratio of 10:1.IntroductionRare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets and batteries (Binnemans et al., 2013; Zhang et al., 2015). REE recovery from alternative sources such as coal and coal byproducts has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials.The average REE content of the world’s coal resources is around 60 to 70 ppm (Zhang et al., 2015). There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia with contents of 300 to 1,000 ppm, the Fire Clay coal seam in eastern Kentucky in the United States with contents around 500 ppm and the Sydney Basin in Nova Scotia, Canada, with contents of 72 to 483 ppm (Birk and White, 1991; Seredin, 1996; Hower, Ruppert and Eble, 1999; Blissett, Smalley and Rowson, 2014). The occurrence of REEs in coal and coal byproducts can be classified into three types: (1) rare earth minerals, such as monazite and xenotime, (2) ion-adsorbed REEs on clays and (3) REEs associated with organic matrices. The rare earth minerals in coal and coal byproducts are very small in particle size, generally on the micrometer and/or nanometer scales (Honaker et al., 2014). Froth flotation, which concentrates minerals based on surface chemistry differences, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime and bastnaesite (Abeidu, 1972; Cheng, Holtham and Tran, 1993; Pavez and Peres, 1994; Pavez, Brandao and Peres, 1996; Jordens et al., 2014). As such, flotation is a promising method for the concentration of rare earth minerals from coal and coal byproducts."

Jan 1, 2017

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

By Frederik H. Kriel, John Ralston, Craig Priest

"Stream-based microfluidic solvent extraction offers a novel alternative to bulk-scale mixer-settler operations. However present maximum throughputs are restrictive and there are engineering challenges that need to be overcome before the technology is robust. This is especially the case for mineral processing, where circuits must be able to handle variable feed streams with long retention times and where maintenance should be minimized. This paper highlights research directed at investigating and evaluating these challenges for actual mineral leach solutions of metal ions. Molecular and particulate channel fouling is discussed. Most extraction systems studied to date show no effects that would preclude use of the technology. For rare earth elements (REE) with fast extraction rates, scale-up of volumetric throughput to 100 L/h using suitable arrays of channels, microfluidic chips and modules is shown to be achievable using a small contactor (approx. 2 m3) platform. This requires only 2–3 % of the typical aqueous phase inventory and residence time used in an equivalent mixer-settler. For a circuit with 100 contactors, the overall residence time would be less than 1 h, using an aqueous inventory of 40 L.INTRODUCTIONHydrometallurgy is of pivotal importance in many mineral processing circuits around the world, with liquid-liquid solvent extraction (SX) a key step in the separation of many base metals (e.g. Cu and Ni), radioisotopes, precious metals, and the ‘technology’ metals, such as rare earth elements (REEs) (Ritcey & Ashbrook, 1979). The standard equipment for SX in mineral processing is the mixer-settler, in which liquid dispersions are created, by agitation, to increase the surface-to-bulk ratio and, thus increase the mass transfer rate between the liquid phases. In stream-based microfluidic SX (microSX), these high surface-to-volume ratios are achieved by contacting microscopic streams (Ciceri, Perera, & Stevens, 2014), rather than forming small droplets, so that phase disengagement can be accelerated (essentially instantaneous via branching of the two streams of liquid at a channel junction). MicroSX is profoundly different from bulk mixer-settler SX operations and offers exciting opportunities for processing hydrometallurgy solutions (Kriel, Holzner, Grant, Ash, Woollam, Ralston, & Priest, 2015; Priest, Zhou, Klink, Sedev, & Ralston, 2012). Nonetheless, the advantages of using microfluidic environments are presently balanced by very significant challenges relating to throughput, process control, coupling of stages, flow stability, and fouling. If these challenges can be met using smart chip designs, process control and clever engineering, high-value/low-volume SX processes stand to benefit greatly."

Jan 1, 2016

By R. V. Fox, L. K. Sinclair, D. L. Baek

"In this study, rare earth elements were recovered from bastnasite concentrate and waste fluorescent lamp phosphors using supercritical carbon dioxide extraction with a nitric acid/tributyl phosphate adduct. Several pretreatment methods were used to alter the crystal structure of the source materials, and thus improve rare earth element recovery. Pretreatment methods included 1) dry roasting of the source material at 730oC, 2) decomposition with 50% sodium hydroxide solution at 150oC for 4 hours, and 3) decomposition with 12 M sulfuric acid at 300oC for 4 hours. Treated and untreated samples underwent supercritical extraction at 24 MPa and 65oC for 1 hour. Untreated bastnasite and phosphor samples showed <10% rare earth element recovery, but sodium hydroxide digestion resulted in >60% recovery for most rare earth elements. Dry roasting of the bastnasite concentrate was also effective, resulting in >60% recovery for cerium.INTRODUCTIONRare earth elements (REEs) consist of the 15 lanthanides, scandium, and yttrium. Scandium and yttrium are included because they are in the same group as lanthanum, appear in many of the same ore deposits as the rest of the lanthanides, and exhibit many similar chemical properties. REEs are used in a wide array of applications including electronics, magnets, catalysts, glass, and solid-state lighting (Xie, Zhang, Dreisinger, & Doyle, 2014). Because of China’s continued dominance of worldwide REE production, the United States Department of Energy has sought to diversify domestic supplies of REEs (United States Department of Energy, 2011). A key part of this strategy is the development of improved extraction methods for both ores and recycled sources.Supercritical fluid extraction (SFE) is a promising technology for extraction and separation of rare earth elements. Contact with an acid adduct dissolved in supercritical carbon dioxide allows for the rapid extraction of REEs from solid matrices. Supercritical CO2 has several potentially useful properties as a solvent, including high diffusivity and the ability to tune solvation properties by adjusting pressure. Such tunability may have applications in separating the REEs once they have been extracted from the solid phase. Tributyl phosphate/nitric acid adducts (TBP:HNO3) are a particularly promising class of adducts for SFE extraction of rare earth elements. Using TBP:HNO3 adducts in supercritical CO2, several researchers have successfully extracted REEs from their oxides (Wuhua, Pijia, & Yongjun, 2010; Zhu, Duan, Xu, & Zhu, 2009). However, there is a complication in applying this technique to many types of ores and recycled sources: REEs are often locked in refractory minerals which are resistant to acid attack, resulting in limited recovery in supercritical extraction."

Jan 1, 2016

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By T Tan, C P. Holmes, C E. Hartford

Transportation of iron ore from the mine to the plant is critical to business success. Ore from the mine may have to be transported across states, countries and even continents to get to the processing plant or export facilities, and ultimately to the client. Numerous transportation steps may result in potential logistical difficulties. Companies are continually seeking ways to increase production rates, decrease delivery times and reduce operating costs. Transportation cost is a major component of the total cost of mining iron ore and therefore requires effective use of transport systems.Bottlenecks in iron ore transport systems, due to material handling issues, can result in loss in profit in the order of millions of dollars per hour. Bottlenecks can be seen anywhere in the transport system where the desired flow rate cannot be achieved. These bottlenecks occur for various reasons such as increasing throughput in a transport system originally designed for a lower throughput resulting in plugged transfer chutes, changing material characteristics (eg finer material, increased moisture content), changing to a new type of material or blend that again alters handleability, or changes in operational philosophy due to equipment availability or process utilisation.Stockpiles may have limited live capacity such that an adequate amount of ore may not be readily reclaimed when required (eg to fill a complete train’s railcars). In bins and hoppers, material may discharge through a central flow channel resulting in the formation of a stable rathole, which can then collapse causing material to flood the downstream system and cause significant downtime for clean-up (eg railcars beneath train load outs). In transfer chutes, bottlenecks can be caused by pluggages or downtime required for the change-out of liners due to excessive wear. In ship loading, long settling or de-aeration time, or material exceeding its transportable moisture limit (TML) may result in further bottlenecks. These bottlenecks all have associated costs because of the need to address their causes and because of the lost opportunities for throughput.This paper will discuss how bulk material technology and proper understanding of material flow characteristics can be applied to mitigate bottlenecks. It will discuss how to predict potential bottleneck locations through a scientific method of analysis and evaluation to determine if an increase in throughput of an existing transport system is possible, as well as whether or not a new material will flow reliably through an existing system.CITATION:Hartford, C E, Holmes, C P and Tan, T, 2015. De-bottlenecking iron ore transportation from mine to plant, in Proceedings Iron Ore 2015, pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By Michael McClintock, Bern Klein

"The high pressure grinding roll (HPGR) is a relatively new comminution technology that is gaining popularity for providing energy efficient solution to hard rock mining operations. A significant barrier to increased adoption of HPGRs is the present requirement for large amounts (excess of 2 tonnes) of sample for pilot testing, which may not be possible for most early stage projects. Three methodologies have been developed at NBK Institute of Mining Engineering at the University of British Columbia that may be used for sizing design optimization of HPGR circuits. All three methodologies use a MTS pistonpress to simulate HPGR comminution. These tests are capable of providing information regarding energy consumption, energy breakage relationship, reduction ratio, and product size distributions. In a period of slow economic development, these methodologies are critical to allow the industry to cost effectively understand the operational benefits of HPGR implementation. This paper examines previous test work done at UBC, as well as the development of an HPGR and piston press database for use in sizing and budgeting of HPGR circuits.INTRODUCTIONCurrently, the mining industry faces several challenges due to falling commodity prices and escalating costs. This has applied pressure for operations and projects to reduce costs and improve project economics. In addition engineering and metallurgical budgets have shrunk as companies try to conserve cash. Improvements and optimization of milling and comminution circuits is one area project economics may be significantly improved. By considering alternative comminution technologies such as the high pressure grinding roll (HPGR), energy operating costs may be greatly lowered. Many have begun to implement HPGR crushing as an alternative to semi-autogenous grinding (SAG) mills, including KGHM and, Sierra Gorda, and Freeport Mc-MoRan’s Cerro Verde operation. However, implementing new technology for companies with little or no HPGR experience may not be practical. An operator must consider both feasibility and economics of a circuit. Currently, consideration of the HPGR requires expensive pilot scale testing for which large sample sizes are needed. In addition, few laboratories are equipped for running pilot scale HPGR test programs. Furthermore, the results of pilot HPGR testing are dependent on the quality of the sample, which cannot represent variations across a deposit. In contrast, ball mills and SAG mills can be sized using the Bond Mill Work Indexes that require a small amount of sample which enable a number of different geological blocks to be tested to allow engineers to have a complete understanding of how the comminution circuit will perform for the life of mine."

Jan 1, 2016

By Zaw Zaw Aye, Sereyroath Chea, Nutthapon Thasnanipan, Thayanan Boonyarak

"As there are only limited numbers of bored pile constructed in sandstone and siltstone in Thailand, load transfer and settlement behavior of a pile in these rocks are still not fully understood. Major factors which influence the performance of the pile in the sedimentary rock should be systematically investigated. The objective of this paper is to analyze load distribution and load-settlement behavior of bored pile in sedimentary rock. Interpreted data was obtained from instrumented load testing results of large-diameter bored piles. These piles were drilled in aeolian soil and socketed in sandstone or siltstone, having socketed length varying from 1 to 3 times the pile diameter. Factors that influenced pile settlement behavior, consisting of rock type at the pile base, socket length, at-rest earth pressure and rock conditions, were analyzed. For interpretation of results, analytical solutions were used to estimate load bearing capacity and calculate settlement of each pile. According to test results of mobilized unit skin friction in siltstone, relationship of 0.1 – 0.3 square root of the unconfined compressive strength of rock appears to reasonably capture the measured shaft friction. Note that shaft movement in siltstone layer was not fully mobilized as maximum pile head settlement was still less that 1% of the pile diameter.INTRODUCTIONExtensive research of bored pile construction in soft soil in Thailand and Myanmar (Boonyarak et al., 2016; Aye et al., 2015) has been carried out. However, behavior of bored pile in weak rocks such as sandstone and siltstone is still not fully understood. Unit skin friction and unit end bearing of piles in these weak rock were reported by Horvath et al. (1983) and Pells and Turner (1980), respectively. Further research is still required to minimize variation in data presented in their study.This paper presents interpretation of load testing results of instrumented piles. These piles were excavated in aeolian deposit in the Northeast Thailand. Some piles were socketed in sandstone or siltstone. Analysis results of load-settlement, shaft shortening, pile settlement estimation, factor for calculating shaft friction and end bearing are reported. Discussion and explanation of pile behavior in sandstone and siltstone is provided.BRIEF INFORMATION OF THE PROJECTProject locationsThe construction sites are located in Khon Kaen and Nakhorn Ratchasima Provinces in the Northeast Thailand. Bored piles in this project were designed for supporting elevated structures for railways, overpasses and U-turn bridges for vehicles. These overpasses and U-turn bridges are distributed along the existing railways with the distance of about 180 km."

Jan 1, 1900

By Ola Lindahl, Mark Irving, John Hutchings

"Blasting is a process starting with a geometric description of the block of rock and ending with a pileof fragmented material. A key step in improving the productivity and quality control over the processis the integration of blast planning software, explosive delivery control systems, and blast recordingwithin one seamless customer solution."

Jan 1, 1997