Search Documents

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

(Members are urged to send in for, this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Aug. 10 to Sept. 10, 1915: Everett L. Booth, New York, N. Y. Raymond B. Ladoo, Cambridge, Mass. T. E. Sturtevant, Dover, N. J. Henry A. Tobelman, Ajo, Ariz. C. A: Filteau, New York, N. Y. R. B.Tinsley, B. Tinsley; Venezuela. Guy C. Riddell, Helena; Mont. ; E. H. Hamilton, Norfolk, Va. Joseph Leiner, New. York; N. Y. M. Yoshimura, Tokyo, Japan. Alfred W. G. Wilson, Ottawa, Canada. Van H. Manning has been appointed Director of the U.. S., Bureau of Mines, to succeed the, late, Dr. Joseph A. Holmes. Mr. Manning was Assistant Director of the Bureau. 0. M. Lewyn, formerly Mine. Superintendent for the Braden Copper Co., has accepted the position of Assistant Mine Manager with the Union Minière de Haut Katanga of South Africa.

Jan 10, 1915

By Paul Levin

A coal preparation plant built with conventional materials only might be able to do an efficient job of preparing coal, but its maintenance costs would be high and emergency shutdowns frequent. To remedy this situation special materials are being used, either in original plant construction or for replacement of conventional materials. The special materials vary from high-strength and abrasion-resisting steels and stainless steel alloys to ceramics. They include hard surfacing welding rods, rubber refractories and some of the newer plastics, the merits of which are cited by the author. A coal preparation plant, limited strictly to the use of conventional materials-for example, mild steel, cast iron and ordinary rubber-could, no doubt, do an efficient job of preparing coal, but the high cost of maintenance and increasingly frequent emergency outages would soon force the operator to seek relief by introducing special materials such as alloyed steels, oil-resistant rubbers and hard-surfacing welding rods.

Jan 6, 1964

By Christopher E. Johansson, William J. Kohr, John W. Shield

Heap biooxidation is an economical means to treat refractory sulfidic ores. However, air flow limitations are a major obstacle in commercialization of this technology. Geobiotics, Inc. has developed a new process for heap biooxidation of sulfide ores that renders the ore more susceptible to bacterial oxidation. In this process, air and liquid flows in the heap are greatly improved by first removing clays and other fine particles from the ore. Gold bearing sulfides are recovered from the removed fines and separately biooxidized. Column biooxidations were conducted on two refractory sulfidic ores from which the fines had been removed in order to improve air flow through the column. Gold recoveries increased from 46% to 90% for a mill grade ore and from 52% to 80% for a low grade ore after biooxidation. Fines and clays in these ores had precluded whole ore heap biooxidation from occurring. This new process addresses the most significant problem of large scale heap biooxidation.

Jan 1, 1996

By Thomas H. Koenning, William E. Bruce

Determination of the state of a mine fire is an important function during firefighting and during rescue and recovery operations. It is imperative that an accurate, up-to-date assessment of fire conditions be available for persons directing such activities in order to avoid unacceptable risk to mine rescue teas and/or fire fighters. Many indicators which consist of ratios of the concentrations of fire gases have been developed over the years for determining the state of a mine fire. Results from numerous gas sample analyses are necessary for determining the trend of the fire. Some indicators are preferred because the influence of sample dilution, a frequent problem, is said to be eliminated. Definitions and examples of indicator6 found to be useful in diagnosing recent western U. S. coal mine fires are presented. Mine gas explosibility is an important subject also requiring rapid assessment. Example explosibility calculations are presented applying one widely used method. Establishing limits for withdrawal of personnel are discussed.

Jan 1, 1987

By Mengxiong Guo, Xuxin Shao

The recent depressant research is summarized, and a new kind of depressant (SCO) has been put forward in this article. Using Na-oleate as a collector and SCO as a depressant, separation of dolomite and phosphate was studied. When SCO was added in the concentration range of 80 g/t to 2kg/t at pH 9.5 ± 0.2, dolomite was absolutely depressed, and apatite kept its floatability. Interestingly, in the mixture of phosphate and dolomite, the dolomite floated. The reasons for such a behavior are investigated through flotation and electrokinetic studies. It was found that the adsorption of dissolved species on dolomite and phosphate resulted in reverse flotation. A concentration of 31.59% P205 and 83.87% recovery of P205 was obtained from the mixture of phosphate and dolomite (2:1) with 26.6% P205 using 210 g/t SCO and Na-oleate 4.93*10-5 M at pH 9.

Jan 1, 1989

By Charles Locke

IT will soon become apparent that the Conference Committee's choice of the title for this presentation is a fortunate one for the speaker; since if it had read "Review of Known Facts Controlling Slag Volume" he would best step down right now. There is a dearth of facts in a quantitative sense on this subject, especially in regard to the effects of slag volume on the acid electric practice for steelmaking, as borne out by a library search involving some 175 references from 1915 to date. Even the opinions in these references on any phase of slag volume are meager. This, then, leads to a report that is candidly based on private observations, on readings and on conjectures gleaned from gossiping with fellow practitioners. Perhaps the subsequent papers, which, as I understand it, are substantiated by actual measurements, of slag volume versus specific contributing factors, will be able to acclaim or disclaim my remarks.

Jan 1, 1947

By John J. Sammarco

Mining, traditionally a low-tech industry, is now utilizing surprisingly complex programmable electronic (PE) systems. The functional safety of PE-based mining systems is an international issue and concern. From 1995 to 2001, there were 11 PE-related mining incidents reported in the U.S. and 71 PE-related mining incidents reported in Australia. These incidents are due, in part, to unprecedented levels of system complexity. The National Institute for Occupational Safety and Health (NIOSH) is addressing this issue of system complexity by conducting research to develop a quantitative complexity assessment methodology based on Normal Accident Theory (NAT). The methodology models the behavioral interactive complexity at the level of system requirements. A graph-theoretical approach is used for creating quantitative metrics from Software Cost Reduction (SCR) dependency graphs. This complexity assessment methodology will help realize simpler, safer systems that will be easier to validate and verify. The methodology will benefit mining and other industries as well.

By A. G. Paithankar, G. B. Misra

Although certain physical mechanical properties of rocks have been claimed to give an estimate of penetration rate in percussive drilling, the authors' work shows that the correlation of penetration rate with individual rock properties is Poor. The authors have developed a good correlation between penetration rate and a set of rock properties but the relation is complex. Energy per unit volume has been used as a measure of penetration rate in percussive drilling by Hustrulid and Fairhurst; however, their test setup is large wing a full size drill bit. The authors determined the minimum energy for unit volume Ev min for any rock at the optimum index angle in a simple laboratory drop tester wing a sharp microbit with a tip angle of ll0°. This Ev min has been found to correlate well with penetration rate obtained in controlled laboratory drilling in different rocks for different stages of bit wear. A comprehensive relation has been developed between penetration rate and Ev min.

Jan 1, 1981

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By Jesús E. Gómez

A recent bridge underpinning project provided a unique opportunity to obtain information on the load-deflection response of 260 hollow-core bar micropiles. All production micropiles were proof-tested to a maximum load of 125 percent of the design load. In addition, four verification tests were performed on sacrificial micropiles to at least two and a half times the design loads. This paper presents the results of the verification and proof tests performed for this project, and provides recommended values for design of hollow core bar micropiles in soils similar to those encountered. This work shows that hollow core bar micropiles provide a significant unit bond capacity in both granular and fine soils, which may be greater than that typically expected in pressure-grouted (Type B) micropiles. The hollow core bar system allows faster installation rates in the soil types encountered than other traditional micropile techniques, and can be installed with relatively simple quality control procedures.

Jan 1, 2007

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours.

Jan 1, 1997

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By C. T. Sheeran, J. C. Franklin

A commercially available microprocessor-based system capable of monitoring 512 channels has been interfaced with monitors for radon, working level, air velocity, and fan power. The basic system utilizes both 280 and 8080 microprocessors in a desktop central processing unit (CPU). CPU hardware includes keyboard, video display (CRT), and disk drive; a printer is used to keep permanent data records. Signals from all channels are transmitted to the computer in digital form where they are processed for alarm status. Software developed for the system allows for audiovisual alarms in the event of low and high readings, rate change, change of state, or communica- tion failure. Up to six channels can be continuously displayed on the CRT for current readings. Shift reports and trend logs may be generated to help the ventilation engineer determine average working levels and ventilation effectiveness. Additional software permits the operator to program command sequences which may be used to automatically restart fans after a power outage.

Jan 1, 1982

By K. Gum, W. C. Hirt, D. A. Rice

Selective flocculation was used to produce a superclean zinc concentrate by minimizing silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, TN. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but never to zinc processing. The feed material assayed 0.45% SiO2. The use of 0.56 kg/ t (1.13 lb/st) sodium silicate and 0.070 kg/t (0.141 lb/st) causticized tapioca starch resulted in a 98.2% zinc recovery and produced a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The target level for silica contamination in JMZ zinc concentrates is currently 0.30% Si02. This work demonstrated that selective flocculation is a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1995

By Rick Sarkisian, Albert D. Bonneau, David Keech

The Drummond Co. Inc.'s Shoal Creek Coal Mine Slope Belt Conveyor transports 5000 mtph (5500 tph) of material over a length of 1400 m (4600 ft.) and a lift of 3609 m (1180 ft.). Four 1500 kW (2000 hp) motors power the 1830 mm (72 in.) Goodyear Flexsteel 5800 steel cable belt. In May 1993, Dodge Manufacturing was selected to design and build the conveyor pulley assemblies for this conveyor. The conveyor includes five pulley assemblies. The 2135 mm (84 in.) diameter by 2135 mm (84 in.) face primary and secondary drive pulleys were designed for a resultant belt load of 3060 kN (688,000 Ib.) This paper describes the design and manufacture of the two drive pulley assemblies. Design details included are component evaluation, material selection, locking assembly selection, bearing selection and lagging selection. Manufacturing details include material procurement, welding process, lagging installation and component assembly. Quality control procedures are also discussed.

Jan 1, 1996

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper' were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor.

Jan 11, 1951

In 1993, the United States' economy grew at a rate of about 3%. The Gross Domestic Product rose to $6.4 trillion. With more than 258 million people - 599,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose 7% to 1.3 million units, new car production fell 3% to 5.5 million units and truck and bus production rose 21 % to 4.9 million units. The rate of inflation was under 3% and the prime rate of interest 6%. The Producer Price Index (1982 = 100) was unchanged from 1992 for fuels and re¬lated products and power at 80 and met¬als and metal products at 119, while chemicals and allied products rose 2% to 128 and non-metallic mineral prod¬ucts rose 2% to 120. The merchandise trade deficit rose 27% to $116 billion.

Jan 1, 1994

By R. D. Groves, G. M. Potter, T. H. Jeffers

Experiments on ammonium carbonate leaching of native copper ores crushed to 1-inch size showed that in 30 days 55 percent of the copper was extracted from 0.7 percent copper conglomerate-type ore, and 85 percent was extracted from 2.1 percent copper amygdaloid-type ore. Cupric ions were not necessary to initiate leaching, and dilute solution containing only 2.2 grams per liter NH3 and 1.9 grams CO, was a suitable solvent. Copper was recovered from the leach liquor by solvent extraction and electrolysis of the strip solution. Cyclic testing of the leach-solvent extraction-electrolytic procedure is in progress on a 6-ton charge of minus 12-inch conglomerate-type ore assaying 2.2 percent copper. Oxygen is metered to the closed leach vessel as required by the leaching reaction. Initial copper dissolution was much slower than from minus 1-inch ore, but the leaching rate then markedly improved.

Jan 1, 1974

By S. Kelebek, S. O. Fekete

The flotation process developed at Falconbridge laboratories utilizes sulphur dioxide and diethylenetriamine (DETA) reagent combination in the depression of pyrrhotite to allow its separation from pentlandite and chalcopyrite. DETA by itself has failed to produce flotation selectivity with samples from plant and pilot plant streams which showed relatively high redox potentials. However, DETA was found to function effectively on laboratory-generated samples under certain conditions. The results of poor depression are in keeping with thermodynamic calculations which indicate that in the presence of sufficient xanthate and DETA, the formation of ferric dihydroxy xanthate and dixanthogen is possible under oxidizing conditions. The use of sulphur dioxide alone has also resulted in a rather poor depression of pyrrhotite. However, the combined use of these reagents has resulted in an efficient and consistent separation of pyrhotite from pentlandite and chalcopyrite. Various aspects of this selective flotation system are presented along with a discussion on possible operating mechanisms.

Jan 1, 1995