Search Documents

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By Dan L'Heureux, Joe Haid, Stephen H. Chung

Most coal deposits in Western Canada involve steeply dipping multiple seams. An efficient way to recover coal seams would be to drill through the seams and blast both the overlying and underlying waste material in one shot without disrupting the coal seams while fragmenting the waste rock for easy removal. This requires special blasting techniques as reported by Chung and Jorgenson in 1985.

Jan 1, 1998

By Dianne M. Lapierre

Mining firms in Canada are increasingly incorporating the social and environmental interests of their stakeholders into their projects in an effort to become more sustainable. Such initiatives have included negotiating Impact and Benefit Agreements (IBAs) directly with would-be impacted, often aboriginal, communities near resource developments in the Canadian north. Why does a mining firm take on this extra time-and cost-intensive initiative when governments and regulatory measures are in place to address social and environmental issues? Past research has paid little attention to the corporate rationales for IBAs. Based on document review and interviews with mining executives, this study investigates the rationales of mining firms that ?over-comply? with legislative requirements by negotiating IBAs or similar types of agreements with communities. The results indicate that mining firms increasingly recognize IBAs as an intrinsic part of the permitting process. When queried, executives regularly identified the negotiation of agreements as ?the right thing to do?. While this response could be read in ethical terms, a commercial rationale is also clearly present. By building strong relationships with nearby communities, addressing community concerns, and directing benefits to local people, all of which are explicitly achieved with an IBA, mining firms are maintaining their long-term financial viability, thus their sustainability, within an evolving industry.

May 1, 2008

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

By Rudolph G. Wuerker

THE Krupp-Renn Process,[1] has been successfully used to treat low-grade iron ores, laterites, titaniferous sands, and other minerals, and before World War I1 25 units were built by the Krupp-Grusonwerk, Magdeburg, Germany. J. J. Howard[2] has shown theoretical advantages of the pyro-metallurgical treatment over conventional approaches; and the process was described by R. Durrer[3].

Jan 1, 1951

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

By Gregory J. Chekan

This Bureau of Mines report presents three methods for designing bulkheads to impound water underground: (1) thin and thick plate design; (2) South African plug design; and (3) single and double bulkhead seal design. Related areas critical to the long-term effectiveness of underground water impoundments are also addressed. These include bulk-head anchorage, concrete specifications and placement, the grouting of permeable strata, and the sizing of barrier pillars. A case study involving hydrostatic tests conducted on a single bulkhead seal constructed in the Safety Research Coal Mine of the Bureau's Pittsburgh Research Center is presented in an appendix.

Jan 1, 1985

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By D. B. Spears

The sillimanite group includes the aluminosilicate minerals sillimanite, kyanite and and alusite, all of which have the same chemical composition (Al2SiO5). This discussion also includes the closely related mineral, mullite(about Al6Si3O15), which, although rare in nature, is produced artificially for industrial use. All of the minerals in this group have a low coefficient of thermal expansion and high corrosion resistance. This makes them desirable for refractory applications, especially in the steel and foundry industries. Other uses include electrical insulators, abrasives and household ceramic products. The minerals in the sillimanite group decompose with an irreversible expansion at temperatures between 1,300° C and 1,600° C (2,372° F and 2,912° F). Sillimanite and and alusite have relatively small expansion on decomposition (4 percent to 6 percent) and, therefore, can be used as aggregates in refractory products. Kyanite’s expansion on decomposition is large (18 percent). So it is sometimes used to balance shrinkage of other materials such as clays in refractory mixtures. For applications requiring high-temperature volume stability, mullite is more desirable. As an additive, mullite improves resistance to creep and corrosion, and imparts thermal and electrical insulating properties.

Jan 1, 2005

By James W. Martin

This user's manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

By Yuting Xue

Classification of rock and coal is one preliminary problem for fully automated or intelligent mining. It assists in automated rib stability analysis and enables the shearer to adjust the drums without human intervention. This paper studies the classification of rock from coal on rib images using machine learning techniques. A database of rock and coal images was created by filtering photographs taken by NIOSH researchers during site visits. Machine learning was conducted on patches, smaller images randomly extracted from each rock or coal image. After training, the classifier was validated with the testing dataset and achieved an accuracy score of 0.9.

Jan 13, 2022

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.