Search Documents

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

Great strides have been made in recent years to reduce the disaster potential of underground mine fires. However, mines can still be caught unprepared for a fire emergency. Fires can grow too large before they are detected, warning systems can be too slow and uncertain to reliably signal the danger, and suppression systems can be inadequate to extinguish the flames. New mining systems and equipment may create unanticipated fire hazards, and new materials may generate highly toxic combustion products. This report contains papers that summarize recent significant developments from the Bureau of Mines mine fire protection research program relating to these problems. Certain of these findings are also applicable to surface mining operations. The papers fall into the general categories of fire detection and instrumentation, fire warning, fire suppression, diesel equipment, spontaneous combustion, and toxicity analysis of combustion products.

Jan 1, 1988

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By Catherine N. Mulligan

Thickening of mine tailings is a relatively new concept for their sustainable management. Removal of water from the tailings to form a paste instead of slurry disposal decreases environmental and geotechnical concerns. As the use of these pastes is relatively new, their behaviour requires investigations such as liquefaction and seismic stability, freeze-thaw behaviour, consolidation and leachate characterization. Slurry density, ore type, particle size distribution, specific gravity and environmental conditions can all influence paste characteristics. In this paper, the effect of the above-mentioned parameters is examined. New developments in water removal, and additives (such as flocculating agents, cements, organics, fertilizers, etc) leading to low moisture content tailings are reviewed, and the potential for thickening to enable sustainable management of mine tailings is discussed with respect to storage volume requirement, use of virgin land, consolidation of the tailings, land use after decommissioning.

May 1, 2007

By M. J. Zdunczyk

The final 1995 figures on industrial sand and gravel have not yet been compiled by the US Geological Survey (USGS). There is usually about a nine-month lag time in receiving and compiling this information. However, USGS estimates that domestic production of industrial sand and gravel will increase about 4% to 28.2 Mt(31 million st). The average unit price is expected to increase as well. The top five producers during 1995 were Unimin, US Silica, Fairmount Minerals, Oglebay Norton and Morie Co. Glass manufacturing for containers, automobiles and buildings was mixed during 1995. Containers, the largest consumer of silica sand, remained steady, with regional increases. However, silica use in glass containers face increased competition from plastic and recycled glass (cullet). It was reported that the Pepsi Cola announced plans to replace glass containers with plastic during 1996.

Jan 1, 1996

By Wesley Hermanson

Canopies were designed, fabricated, installed, and demonstrated for mining machinery in 3-foot coal seams. A Wilcox PJ20 Auger miner, a Wilcox Bolter, a bee Norse 245 miner, and an Elkhorn Scoop AR3 modified to AR4 were fitted with canopies. The Wilcox Bolter canopy was hydraulically adjustable in height; the rest were manually pin adjustable. The machine operators' comments were adverse in each case. Restriction of visibility and body constriction into unaccustowed and tiring attitude were major objections, causing increased hazards and fatigue. Recommendations are made that roll bar protection be furnished in place of canopies for 3-foot seams to provide partial protection by deflecting and supporting roof falls but not covering the head of the operator. In this way, the effect on visibility would be minimized and fatigue from body restriction would not be increased.

Jan 1, 1976

By Anatol Wojtowicz

This research program was conducted to determine if respirable coal dust emanating from a continuous mining machine can be suppressed more effectively by a high expansion foam than by the water sprays conventionally used. A high expansion foam system was developed and tested on a continuous mining machine under actual operating conditions. The utility of the system was demonstrated. Test results tend to show that foam application is more effective than water sprays in suppressing respirable coal dust. However, because of the extreme variability of the test conditions, scatter in the sampling data, and other factors, not enough data was obtained to form a firm conclusion that foam is more efficient than a water spray in suppressing respirable coal dust. Sufficient statistical data was obtained, however, to indicate that foam is more efficient than water in suppressing total float coal dust.

Jan 1, 1974

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By Raymond Chenier

British Columbia (BC) is Canada’s most western province. The landscape in BC is amongst the most beautiful and pristine in the world. Along with its beauty come vast mountain ranges, coastal rain forests, swamplands, deep river valleys, and almost every type of landscape imaginable. These all have, or at one time had, logging roads constructed. Some of these areas should never have had roads constructed due to poor drainage and unstable slopes, but some of the roads could be considered engineering masterpieces. To navigate a vehicle the size of an off-road logging truck down the side of a mountain with an 80°h side slope or greater can be a hair-raising experience. Not to mention coastal rains and/or high elevation blizzards. These factors collectively make logging BC’s most hazardous occupation. People are seriously hurt, sometimes even killed everyday.

Jan 1, 2001

Division of Geology, State of Tennessee, 401 Seventh Ave, North, Nashville, Tenn. Walter F. Pond, State Geologist A selected list of Bulletins available: Bulletin 1(B), Bibliography of Tennessee geology (1911); 2(A) Outline introduction to mineral resources (1910), 2(D) Marbles (1911); 2(G) Zinc deposits (1910), 16, Red iron ores of east Tennessee (1913), 22, Geology and natural resources of Rutherford County (1920), 24(A) Geology and oil possibilities of parts of Overton, Clay, Pickett and Fentress counties (1920); 24(B) Oil and gas resources of northeastern Sumner County (1920), 26, Mineral resources of Waynesboro Quadrangle (1921); 28, Marble deposits of East Tennessee (1923), 29, Magnetic iron ores of east Tennessee (1923), 31, Zinc deposits of east Tennessee (1923), 33, Tennessee coal fields, 37, Geology and mineral resources of Hardin County, 38, Stratigraphy of the Central Basin (in press), 39, Brown iron ores of the Eastern Highland Rim (in press) From 1911 to 1919, inclusive, volumes were issued annually on The Resources of Tennessee Only a few of the separate papers contained in those volumes are now available Vol. 2 (1911): No 1, Explosions of coal dust in mines, and other papers, No. 4, Lignite and lignitic clays in west Tennessee, and other papers; 5, The growth of knowledge of Tennessee geol¬ogy; 9, The valley and mountain iron ores of east Tennessee, 10, The iron industry of Lawrence and Wayne counties, and other papers; 11, Barite deposits in the Sweetwater district, and other papers, 12, The iron ore deposits in the Tuckalioe district, and another paper Various oil maps (15 to 40 cents each) and traverse maps of counties (25 cents and 31 each) can be had, as well as pertinent U. S topographic maps.

Jan 1, 1933

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By Launa Mallett, Michael J. Brnich

The first step to emergency preparedness is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen all at once. Risk assessments are used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. While the examples provided in this training package are specific to mine fires, the concepts and tools can be applied to any mine hazard. Purpose: This training package was developed to assist instructors, as they: 1) determine how to use risk assessment to improve preparedness for mine fire emergencies and 2) present risk assessment concepts and tools to trainees. Audience: This package is appropriate for workers/trainees from all types of mines. A risk analysis can be conducted by anyone familiar with the location(s) being studied. Why Conduct a Fire Risk Assessment? During a risk assessment, hazards are evaluated in terms of the likelihood that a problem may occur and the damage it might cause. Mine fire preparedness requires consideration of all possible fires that could occur. However, at a given mine some fires are more likely than others and some would result in greater damage than would others. Conducting a risk analysis identifies these differences. The results can be used to target resources at the types of fires that are most likely and/or are most destructive. Hazards that are very likely to result in fires that would do considerable damage to people and property should be targeted first for remediation and/or effective response if remediation isn't possible. Potential fires that are less likely or that would have less severe consequences are identified for attention later, after the more serious situations have been addressed.

Jan 10, 1992

1. Recent publications Canadian minerals yearbook 1986. Review and outlook. Mineral Report 35. Available from Printing and Publishing, Supply and Services Canada, Hull, Quebec KIAOS9, Canada. $44.70. The 1987 Sigma cataloge. SI. Louis (USA), Sigma Chemical Co., 1986. 1736 pp. Der Maschinenschaden. Munchen(G. rmany), Koningstrasse 28. Metallurgicalworks in Canada primary iron and steel 1987. Mineral Bulletin MR 214. Available from the above address at $6.60 per copy. Annual report 1986. Oxbridge, International Research Institute, 1987. Canadian iron ore industry statistics, 1986, by B.W. Boyd and A. Cadieux. Publication MRI 87/6. Micromedia Limited (Document Delivery, 165 Hotel de Ville, Place du Portage 2, Hull, Quebec J8X 3X2, Canada). Tin and its uses no. 153. Oxbridge (England), International Tin Research Institute, 1987. This issue includes articles on can-making, titanium-tin alloy, coppernickel2. New journal Pergamon are producing a new journal, entitled Minerals Engineering, which they describe as 'an international journal devoted to innovation and developments in mineral processing and extractive metallurgy'. 3. Mintek publications Report M298. The effect of flocculant additions to the leaching solution on the kinetics of the oxidative dissolution of sphalerite, by F.K. Crundwell. Report M304. The smelting of ilmenite in a d.c. transferred-arcplasma furnace with a molten-anode configuration, by AD. Brent. Jut 1987. 17 pp. Report M312. The reactions of some thiol collectors at noble-metal and pyrite electrodes, by D.R. Groot. Jut 1987. 21 pp. Report M321. The determination of molybdenum, arsenic, and uranium in activated carbon by X-rayfluorescence spectrometry,by A.M.E. Balaes and G.J. Wall. Aug. 1987. Report M321. The determination of molybdenum, arsenic, and uranium in activated carbon by X-rayfluorescence pectrometry, by A.M.E. Balaes and G.J. Wall. Aug. 1987.

Jan 1, 1988

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

By Jerry Z. Lu

Belt conveyor design involves the evaluation of belt tensions, drive selection, pulley configuration and other technical issues. The conveyor belt tensions vary with conveyor layout, drive pulley configuration, belt selection, and idler selection. The decisions for the belt conveyor construction always take all technical, commercial and maintenance issues into consideration. A good conveyor design shall provide required operational features and at the same time be cost effective. The common issues for an engineer to face during belt conveyor design include: (1) Conveyor drive selection ? drive with fluid couplings or variable frequency drives; (2) Drive system configurations - single pulley large drives or dual pulley smaller drives, if intermediate tripper booster drives shall be applied, what power ratio should be adopted for a multi-drive conveyor; (3) Gear reducers ? shaft mount drives, right angle gear reducers or parallel gear reducers; (4) Drive pulley lagging - ceramic lagging or rubber lagging; If ceramic lagging, what type should be used. (5) Conveyor speed variation ? If conveyors run at variable speeds, faster speed/lower percentage loading or slower speed/higher percentage loading. In many cases the decision maker find themselves in a dilemma ? technical benefits vs. financial benefits, capital cost vs. operational cost, and capital and operational cost vs. maintenance effort. Although many conveyor design topics above have been discussed in numerous technical papers and design reference books, management executives and inexperienced engineers may be confused and feel lost. The consultation of people around them may lead to different opinions since experiences tend to vary, making the decision making process complicated. The purpose of this paper is to simplify these complicated issues and provide useful guidelines for belt conveyor design. This paper focuses more on providing simple and practical answers and solutions instead of discussing each topic academically and theoretically in depth.

Nov 1, 2011

By Kathleen Kowalski-Trakofler, Edward Barrett

Problem: It is estimated that 5 to 10 arc flash explosions occur in electric equipment every day in the United States. In the mining industry the largest single injury category of electrical injuries are caused by non-contact electrical arcs. Method: This investigation progressed in two phases: (a) 836 Mine Safety and Health Administration (MSHA) reports of electric arcing incidents that occurred over a period of 11 years were reviewed, and (b) personal interviews were conducted with 32 individuals. A theoretical Safe Job Performance Model guided the study. Results: Behavioral dimensions were identified and included the effect of worker experience, judgment and decision-making ability, behavioral and organizational controls, and safety culture. Summary: The National Institute for Occupational Safety and Health (NIOSH) conducted an investigation of behavioral components associated with arc flash incidents and developed recommendations for interventions based on findings. Impact on Industry: This study fills a vacuum in electrical training with a focus on the organizational and behavioral aspects of arc flash incidents. There search is cross-cutting in its scope, in that the results apply not only to mining and construction, but many other industries employing electricians. Although the majority of mine electrical injuries are the results of burns from electrical arcs, few miners are aware that such a hazard exists. A safety training program, which includes a video and an instructor's discussion guide, was developed for electricians based on this study's findings. “Arc Flash Awareness” was released in 2007 (DHHS NIOSH PublicationNo.2007-116D) and is available through1-800 CDC-INFO. Phone:1-800232-4636 or email cdcinfo@cdc.gov. It is also available from MSHA at MSHADistribution@dol.gov or 304-256-3257 (DVD-576). Private industry is producing Portuguese and Spanish language translations.

By J. A. Bartnik, Gerald D. Rose, William H. Benson

New techniques in the magnetite and heavy media beneficiation industries demand more efficient magnetic dispersion and flocculation of the finely ground particles. Demagnetizing coils must produce several major effects, such as improving classification and screening efficiency, decreasing moisture content in filter cake and improving separation selectivity and green pellet properties. Likewise, magnetic flocculators must increase filtering rates and the settling rates of solids, improve magnetite recovery and produce cleaner water. To improve the design of equipment and to conduct tests leading to the optimization of such dispersion and flocculation, a program was initiated at Eriez Magnetics. The major conclusions reached are: 1. Laboratory and plant scale tests conducted on magnetite products show that a demagnetizing force of 450 rms oersteds at 60 cycles for 1/20- second duration will depolarize natural magnetite particles coarser than approximately 10 microns. This has been found satisfactory for most applications. 2. Effective flocculation of magnetite was obtained when a slurry with more than one percent magnetite was exposed for a period of approximately 1/15 second to a 600-gauss field. 3. The cost of demagnetizers (or flocculators) increases rapidly for larger diameter pipes. In order to reduce the cost, narrow rectangular sections are recommended for magnetic flocculators. 4. For minimum operating cost, permanent magnetic flocculators are ideal, chiefly because they do not require any maintenance and have no operating cost. 5. A newly designed electro-demagnetizing coil with high heat dissipation and a nonmetallic core provides high efficiency and long life. 6. To select the correct magnetic flocculator (or demagnetizing coil) the following information is necessary: a. Magnetic product susceptibility b. Magnetic product coercive force c. Percent of magnetic product d. Flow rate e. Viscosity f. Structure of magnetic product

Jan 8, 1968

By Perry G. Harrison

The increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well.to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd continuously operated sinter-machine installations located anywhere. Per Crude Ton Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? Per Sinter Ton Royalty on ore 0.10 Royalty on flue dust 0.15 Per Crude Ton "Winter expense"; i. e., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for any ore, viz: Per Crude Ton Per Ton Handled Sinter 1. Flue Dust—Steel Plant Locations Sinter recovery, 15 per cent moisture and carbon 85 per cent Labor, supplies and repairs 0.15 0.18 Power 6.5¢ X 1¢ kw-hr. 0.065 0.08 Plant overhead and administration 0.05 0.06 Depreciation per ton 0.05 0.06 Dust handling and preparation 0.10 0.12 Fuel: free, contained in dust Ignition: blast-furnace gas free Royalty 0.15 Total $0.65 Note:—Cost increased by either deficiency or considerable excess of carbon in dust.

Jan 1, 1932

By Vasil Kopaleishvili

The bainitic Fe-C-Si alloys with optimum content of retained austenite serve as ?containers? for storing of hydrogen. Both the vacancies of fcc lattice and the possibility of forming hydrides of silicon and other alloying elements will be used. The idea is based on our scientific hypothesis. There is the silicon threshold (Si=0,50%) in "Fe-Si" system and Fe-C bainitic alloys, above which it causes self-organized phenomena: sudden increase of hydrogen solubility and amount of retained austenite in the alloy after ??ß transformation, formation of two supersaturated solid solutions <a??r>, "rejuvenation? and its reverse process. Rapprochement of iron atoms when Si=0,50%, causes appearance of new covalent forces where uncompensated electrons of 3d-subshell are involved and it provokes synergetic phenomena. They ?free? silicon atoms from the previous bonds. After that silicon itself becomes a getter of hydrogen using vacancies (14) of 3P2(6)d0(10) subshell and it results in sudden increase of hydrogen solubility in metal. Simultaneously sudden decrease of iron activity takes place. That in its turn ?releases? the carbon. Thus, its redistribution, controlling the bainitic transformation, is hastened. It stipulates for creation of ?brittle bainite" B[a(C,H)+?r(C,H)] after ??ß transformation. While weathering of metal, "rejuvenating", hydrogen diffuses in ?islets? of retained austenite and ?relaxed bainite? (B[(C)+?r(C,H+H)]) is obtained. When heating austenite ?(C,H) is obtained, and after cooling ?brittle bainite? is obtained, etc. Presented scientific hypothesis explains the available experimental facts ("rejuvenation? and its reverse process, graphitization, weldability, forming of flakes, reaching high strength, etc.) in a new manner, as well as, gives real opportunity for creating of new trends in many fields, e.g. iron based HAA. Provisional data having been obtained are encouraging.

Jan 1, 2006