Search Documents

By Michael R. Brown

A facilities success or failure of doing well during a regulatory inspection is typically measured by the number and type of citations that result, and financial liability resulting from those citations. The success of a facility during an inspection depends on several factors including, the preparation prior to an inspection, behavior and activities during and inspection, and finally, action taken following the inspection. This paper contains suggestions for improving inspection results and establishing an attitude of compliance at manufacturing and mining facilities.

May 1, 2002

By Patrick Wong

The design of piling platforms is addressed in BRE (2004) for both fine grained and coarse grained subgrades. However, for coarse grained subgrades, piling platform designs can often be overly conservative due to either conservative assumptions on soil friction angle, or concerns over density variations of granular fill, particularly for made-ground. This paper provides guidelines on economic design of piling platforms on coarse grained subgrade by providing recommendations on ground characterization, assessment of soil properties and the use of non-linear stiffness soil behavior. An innovative performance-based design approach is also introduced, utilizing proof rolling with associated testing and interpretation using small strain theory to overcome concerns regarding potential ground variability of made-ground. A case study is presented to demonstrate the successful application of this performance-based approach to avoid having to construct a new piling platform over a 2 ha area. Small strain, non-linear stiffness theory was used to enable a practical proof rolling pressure to be adopted without having to reach the design or ultimate operating pressure. The author considers that the performance-based approach adopted on the case study may be similarly applied to a range of other projects to derive economic solutions.

Nov 1, 2022

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957

By E Matinde, M. Mnisi, I. C. Thobadi, W. Clark, J. D. Steenkamp

Pyrometallurgical smelters utilise tap-holes, through which liquid metal, matte and/or slag are tapped at regular intervals. However, tap-hole failures can have a devastating impact on smelters, which includes loss of equipment, human life and business interruptions. Contributing factors to tap-hole failures include poor and/or incorrect refractory material selection, including tap-hole clays. The functions of tap-hole clays in smelters include their ability to be extruded and drilled with ease at the end and beginning of a tap, and their ability to resist chemical wear due to molten metal and slag during tapping. Mintek is currently developing methods of evaluating properties of tap-hole clays with a specific focus on workability, and wear mechanisms of clays due to ferrochrome alloy and slag. Of particular interest to this study was the characterisation of various tap-hole clays. This paper evaluates the chemical and phase chemical properties of three different tap-hole clays. The bulk chemical composition of the tap-hole clays was determined by inductively coupled plasma optical emission spectroscopy, proximate analyses and combustion methods. The bulk phase compositions and specific phase chemical compositions were studied using quantitative X-ray diffraction, scanning electron microscope and electron probe microanalyses techniques. Keywords: Tap-hole clay, chemical analyses, phase chemical analyses, ferrochrome

Jan 1, 2020

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By J. B. Gayle

Because economic and geographic factors have focused particular attention on the use of anthrafines in blends containing Lower Kittanning coal as the low-volatile component, samples from this particular bed were selected for experimentation whenever practical. Carbonizing tests were carried out in accordance with standard procedures, using the Tuscaloosa and sole-heated ovens. Most of the results are in general agreement with those reported by previous investigators. Specific findings are as follows: (1) The effectiveness of anthrafines in reducing coal expansion is such that even highly expanding, low-volatile coals can be carbonized safely with suitable additions of anthrafines and careful control of charge density. (2) Increases in coke size, resistance to shatter, and apparent specific gravity appear to be characteristic for additions up to approximately 15 percent to a fixed base blend. When anthracite of minus-48-mesh size was used and the proportion of low-volatile coal simultaneously increased, these indexes increased only slightly or remained substantially constant. (3) No increase in breeze formation was noted for additions in amounts up to 15 percent. (4) Abradability of coke was increased by additions of anthracite of No. 5 Buckwheat size, but it either decreased or remained sub¬stantially constant when the inert was ground to pass a 48-mesh screen.

Jan 1, 1956

By Morgan Schauerte, Laura Raimondi, Mariel Palomeque

Executives in the mining industry are facing dramatically changing market expectations on reporting and transparency regarding the environmental and social impacts of projects, supply chains and products. Companies increasingly need to disclose the governance procedures they have in place to ensure communities, investors, employees, and Indigenous partners are effectively managing social and environmental risks. These disclosure requirements begin during exploration and carry through to all stages along the project life cycle. This type of environmental, social and governance (ESG) disclosure is referred to as ESG performance by the investment community. ESG is not a new concept, and it builds on and is intertwined with many concepts such as corporate sustainability, corporate social responsibility, eco-efficiency, triple bottom line thinking, life cycle management and many others. This paper will explore how mining companies can develop a credible ESG governance approach and strategy that will reduce risk, open opportunities, and create value. This paper will summarise ESG trends and drivers, discuss the economics and investors’ perspective towards ESG, and outline leading ESG standards and guidelines of interest to investors, regulators, communities and other stakeholders. Linkage of ESG to global sustainability efforts such the United Nations Sustainable Development Goals and Global Compact will also be addressed.

Jan 1, 2023

Ground falls (roof and rib) have historically been responsible for nearly 50% of all fatalities in bituminous underground coal mines. In recent years, the number of some annual ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, the twin disasters at Crandall Canyon in 2007, in which nine miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990s, these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents since 2005. Progress has also been made in pillar recovery, where there has been just one fatal incident since 2005. On the other hand, more than 300 miners continue to be injured each year by rock falling from between supports and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities available technologies such as roof screen, rib bolting and inside control roof bolters could reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety.

Jan 1, 2011

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By I R. F MacCulloch

Bacterial oxidation of sulfide minerals is a familiar and commercially available process to enhance gold recovery with problem ores. Pintail Systems, a Colorado, USA based company had developed bio-processes for gold recovery based on natural mineral formation and transformation in a global mineral cycle. The biological recovery of precious metals from ore involves a number of mechanisms that are dependent on the metal-mineralogical association. These processes include: partial bio-oxidation of sulfide ores; oxidation of gangue minerals exposing gold to leaching; surfactant properties of bacteria/nutrient solutions that improve wettability of ores and solution contact with leachable gold and silver; and microbial production and excretion of trace amounts of gold lixiviants, and bio-fracturing or biological alteration of ore minerals. Pintail has demonstrated enhanced recovery of precious metals during cyanide detoxification of spent heaps at the end of mine life. Biological recovery processes also have the potential to be applied to in situ mining technologies. The in situ process application could recover gold from subgrade deposits, small deposits or those ore bodies with uneconomic stripping ratios for conventional mining. In situ biomining can be accomplished at a fraction of the cost of conventional mining and leaching and does not have the environmental liabilities associated with many conventional gold lixiviants.

Jan 1, 2004

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By S Walters

The emerging discipline of ‘geometallurgy’ is not new but is becoming increasingly recognised as a discrete and high-value activity. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance behaviours. A key outcome is enhanced economic optimisation of mining and improved risk management tools.Industry recognition of the need for large-scale, integrated research to support this emerging area resulted in commencement of a major ongoing initiative in mid-2005. The AMIRA International P843 ‘GeMIII’ project (Geometallurgical Mapping and Mine Modelling) is a cross-discipline collaboration involving a number of world-class research organisations supported by over 20 industry sponsors.The project is delivering integrated tools and methods which link intrinsic rock characteristics to prediction of mineral processing performance. These indices must be capable of spatial distribution in 3D resource models and incorporation into mine planning and optimisation. A key aspect is provision of new cost-effective tools and methods which can provide the large numbers of measured and estimated data points required to undertake effective modelling and spatial distribution. The integrated methodology and enabling technologies being developed through the ongoing AMIRA GeMIII project are outlined, together with implications for supporting industry best practice.

Sep 5, 2011

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida's sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants' and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

By M. M. Tilman

As part of ongoing research to improve mine safety, the Bureau of Mines conducted research on the corrosion of friction rock stabilizer steels in five Missouri lead and iron mine waters. Electrochemical corrosion tests, including evaluation of pitting tendency, were performed on two types of high-strength, low-alloy (HSLA) steels and galvanized steel in four Missouri lead mine waters and one Missouri iron mine water. The tests were conducted at in-mine water temperatures in both air-saturated and deaerated waters. Static, weight-loss corrosion tests were also conducted on HSLA steel specimens in the five Missouri mine waters for 2,900-h duration at average in-mine water temperatures and air-dissolved oxygen contents of 6 to 7 ppm. Corrosion rates determined by the weight-loss tests were roughly comparable with rates determined electrochemically in deaerated waters containing 0.3 to 0.5 ppm dissolved oxygen content. Passivation of specimen (nongalvanized) surfaces in air-saturated waters resulted in very low electrochemically deter- mined corrosion rates. Pitting-tendency was generally higher for both HSLA steels in air-saturated waters than in deaerated waters. Galvanized steel generally exhibited higher tendency to pitting in the deaerated waters than in the aerated mine waters.

Jan 1, 1985