Search Documents

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By James P. McGee

Use of nuclear reactors to furnish high-temperature heat is a field that has not received as much attention as propulsion and electric power production. Investigations are being conducted under a joint Atomic Energy Commission (AEC)--Bureau of Mines research program to determine the feasibility of using nuclear heat for chemical processing. A part of this process-heat-reactor program is the study of a system in [hich] helium transfers heat from 8 nuclear reactor to a chemical processing [essel]. This requires construction of (1) a nuclear reactor to operate with helium exit temperature of 2,500° F. and with pressures in the range of 250 to 500 p.s.i.g. and (2) a processing vessel (heat exchanger) to convert the enthalpy of the helium into chemical process reaction heat. Neither component exists at present, and development of each promises to be a formidable task. To aid in the study of such a system, the Bureau of Mines has designed and constructed a vessel heated by electrical induction to simulate a source of nuclear fission heat. This vessel is undergoing preliminary testing. Gasification of coal and reforming of hydrocarbons are promising uses for nuclear heat. It appears that a higher price per unit of nuclear heat can be tolerated for chemical processing than that allowable for power generation.

Jan 1, 1960

By Manjeet Chowdhry, Qingxia Liu, Phillip Choi, Zhenghe Xu

Computational chemistry methods, such as density functional theory (DFT), are powerful tools to quantify reagent-mineral interactions encountered in sulphide mineral flotation. A quantitative relationship between theoretically calculated parameters based on chemical structure of collectors and their reactivity with different metals/minerals can provide valuable insights for design and development of more powerful and tailor-made reagents offering enhanced metal/mineral selectivity. DFT calculations at B3LYP/6-311++G(3df,3pd) level were employed to elucidate the reactivity of neutral sulphide collector reagents, including thionocarbamates (TC), thioureas (TU), xanthogen-formates (XF), dialkyldithiocarbamates (DTC) and dialkyltrithiocarbonates (TTC) with different heavy metal ions (Cu2+, Zn2+ and Pb2+) in solution. The extent of delocalization of lone pair electrons of heteroatoms (attached directly to C in C=S) over C=S group was found to be the dominant factor in determining the collector’s reactivity. Order of reactivity was established as: TU > TC > XF > DTC > TTC. All the collectors showed superior affinity towards copper followed by lead. Unidentate binding was observed through sulphur atom except for xanthogen-formate for which bidentate binding mode was observed. Effect of nature of substituent groups at N and/or O atom on reactivity of thionocarbamate and thiourea was also investigated. The results obtained through DFT calculations are consistent with the experimental data reported in literature.

Jan 1, 2015

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize biomass productivity, the influence of reclamation practices on biomass production must be well understood, which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass estimations and, also, the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, experimental biomass production plots on reclaimed mine sites established in Wise County, VA, are used for a comparative study of satellite spectral derivatives, which are evaluated against groundbased biomass estimates. Metrics based on four spectral derivatives, band ratios and spectral transforms were regressed against biomass measured in situ for different species. The results demonstrate that greenness and principal component 2 (PC2) were more efficient than the other spectral derivatives for monitoring the biomass of this reclaimed area. Also, it is shown that Landsat-5 TM has provided promising results for monitoring of the biomass changes occurring from 2008 to 2010 over the study area.

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By B Hannah, M Uriarte, F Labarca, C Madore, G Ganapathi, L Martin, T Haase

BechtelÆs Mining and Metals projects across the globe are executed in remote arid and semi-arid countries where providing even basic water supplies impose considerable challenges. Opportunities for water conservation measures using a Six Sigma initiative were proactively pursued to address the potential business impacts of limited availability of water resources. The initiative investigated areas driving water-optimisation during concrete operations and camp management. This paper details the water conservation evaluation of alternatives and cost/benefit analysis based on current and predicted water usage for development projects. Optimisation of water consumption through institutionalising more prescriptive standards for camp design and defining water conservation requirements have resulted in a new standard specification. Based on our projected mining project workload across the globe, it is estimated that for the period 2012 - 2015, a potential 5.5 M m3 water savings resulting in US$11 M could be realised for construction camps and savings of 4 M m3 of peripheral concrete process water resulting in potential cost savings of US$8 M could be achieved as a result of these revised standards.CITATION:Haase, T, Hannah, B, Ganapathi, G, Martin, L, Madore, C, Labarca, F and Uriarte, M, 2013. Water conservation at construction projects, in Proceedings Water in Mining 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Nural Kuyucak

Acid mine drainage (AMD) occurs at operating and abandoned mine sites as a result of oxidation of sulphide minerals, and is characterized by low pH and heavy metal contamination (e.g. Fe, Zn, Cu, Cd, Al, Mn). It usually requires treatment before release in order to meet regulatory requirements. Chemical methods, such as lime neutralization and sulphide precipitation, are commonly used to treat AMD. However, the conventional processes require high capital and operating costs, and constant attention for many years into the future. In addition, the amount of sludge produced by conventional lime treatment processes poses an increasingly significant disposal problems at decommissioned mining operations. There is, therefore, an urgent need to develop passive, cost-effective processes for mitigating AMD and seepages originating from tailings and waste rock areas. Noranda Technology Centre (NTC) has been evaluating various methods being developed by other institutions, and exploring new ideas, to achieve passive in situ processes for treating AMD. These methods include anoxic limestone (ALS), lime-organic mixture (LOM), biosorbents (BIOS) and biotrench (BT). Current investigations at NTC involve preliminary bench-scale testing. Based on the outcome of the bench tests, a field test will be performed at a selected site. Details of the bench tests are discussed in the paper. Key Words: Acid mine drainage, treatment, metals removal, passive treatment, anoxic lime, limestone, biological treatment, sulphate reducing bacteria, biosorption, biosorbent

Jan 1, 1993

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By LeRoy D. Loy

To facilitate effective land reclamation and comply with existing state regulations, surface coal mine operators have in recent years adopted new mining techniques and equipment utilization for steep-terrain mining. In contrast to direct spoiling with draglines or shovels, these new mining methods require some form of overburden haulage from the excavation face to the point of reclamation. Although current mining methodologies such as Block-Cut, Modified Block-Cut, and Mountaintop Removal with Head-of-Hollow Fills have proven effective in achieving reclamation objectives, some production problems have resulted from pit congestion and excessive equipment delays. Recognizing this problem, the United States Bureau of Mines contracted Skelly and Loy to design innovative mining concepts utilizing conveyor haulage in place of trucks, loaders, dozers and scrapers. Project objectives required definition of current bottlenecks and development of mining systems to: alleviate bottlenecks; increase production potential; facilitate additional resource recovery; enhance reclamation; reduce safety hazards; and improve mining economics. Successful completion of project goals within a four year program involves systematic implementation of the following separate work phases: 1) Develop Concepts for Block-Cut Mining Systems; 2) Determine the Economic and Technical Feasibility of Concepts; 3) Prepare Detailed Design and Specifications of Concepts; and 4) Prepare Specifications for Conducting Field Tests of the Most Promising Concepts. At the time of this publication, Phases 1 and 2 are finalized with Phase 3 efforts well underway.

Jan 1, 1977

By A. Deepatana

This study compares the use of an aminophosphonate chelating resin Purolite S950 and a sulphonic acid strong cation exchange resin Purolite C160H to recover nickel and cobalt from the synthetic bioleach solutions. Batch adsorption of metal citrate is performed as a function of metal citrate concentration (15~2000 mg/L) and solution pH (0.01M and 0.1M citric acid). The adsorption mechanism as inferred from the fit to Langmuir (LM), Freundlich (FM) and Redlich-Peterson (RP) models demonstrates that nickel citrate adsorbed onto C160H appears monolayer in comparison to that adsorbed onto S950 exists multilayer. In contrast, cobalt citrate adsorption onto both C160H and S950 agrees with the LM model. The results have shown that loading capacities of nickel and cobalt citrate onto C160H are 60 and 65 mg/g whereas those observed onto S950 are 16mg/g and 6 mg/g respectively. These are achieved in metal citrate prepared in 0.1 M citric acid. Resin regeneration is conducted in using 2 M nitric acid solution. The results show high efficiency of nickel and cobalt citrate elution from Purolite C160H. Findings from this study suggest Purolite C160H is a suitable adsorbent for recovering nickel and cobalt from bioleaching solutions.

Jan 1, 2014

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By Richard D. Graves

Pitch from low-temperature carbonization of bituminous coal was hydrogenated at cracking conditions in a continuous bench-scale unit to produce low-molecular-weight oils and tar acids. The pitch contained 15.6 pct benzene-insoluble material, 4.0 pct hexane-soluble oil, and 80.4 pct asphaltene by weight. At 475° C, 7,500 psig, and 1.5 hours residence time, hydrogenation products, based on the weight of pitch, were about 36 pct oil boiling below 325° C, 24 pct hexane-soluble heavy oil, 17 pct asphaltene, 1 pct benzene insolubles, and 12 pct hydrocarbon gases. The yield of tar acids boiling below 250° C was 4.3 pct, and the yields of C6 to C8 paraffins, naphthenes, and aromatics were each less than 1.0 pct. The yield of tar acids was within the range of yields obtained by hydrogenation or high-temperature carbonization of bituminous coal (2 to 5 wt pct). Yields of oil boiling below 325° C increased with increased residence time or temperature. There was little or no effect of residence time on yields of alkali- soluble material which contained tar acids. Yields of hydro-carbon gases increased markedly with an increase in temperature from 475° to 500° C. Lowering the hydrogen pressure to 4,500 psig resulted in yields similar to those obtained at 7,500 psig.

Jan 1, 1962

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By Y. Waseda, S. V. Gnyloskurenko

"Present paper reviews the various processes for making of metallic foams. These methods are classified in accordance with the state of initial metals - liquid, powdered and ionized. Liquid metal can be foamed by direct inputting of gas into melt, using gas releasing foaming agents or producing supersaturated metal-gas solutions. This group also includes methods creating voids in the melt. Powder route is based on using powdered matrix metal with foamable precursor materials. Finally Deposition techniques allows making highly porous metallic structures using ionized metal.Experimental study presented shows importance of wettability in bubble formation at gas blowing into melt simulation liquid (water) through holes. Good wettability of injection holes by water ensures formation of bubbles with smaller sizes that effect to the final foam structure.IntroductionOne of the objectives of future production technology is to make of lightweight constructional materials while achieving improved property and good economy as well.The most perspective lightweight materials are cellular or foamed materials that are Wide8pread. in nature and have a growing interest in industry and everyday life.Even metals and metallic alloys can be produced as cellular solids or metal foams beside of the traditional engineering materials such as polymers, ceramics or glass. Recent developments in metal foams, especially aluminium, have produced a new class of lightweight materials."

Jan 1, 2000