Search Documents

By D. H. Baker

This report, one of a series prepared by the Federal Bureau of Mines on the technology of titanium, describes the development of an electrorefining cell from which cathode deposits up to 30 inches long can be produced. Data show individual deposits to be homogeneous, comparable from top to bottom, and not varied in quantity or quality of metal over the entire length of the deposit. Investigations concerned with various diameter cathodes showed that cathode current efficiencies were materially reduced with cathodes less than 2 inches in diameter. Deposits produced on 1/2-inch-diameter cathodes showed cathode current efficiencies of 19 percent and on 1-inch cathodes, just over 22 percent, whereas deposits produced on 2- and 4-inch-diameter cathodes showed about 70-percent current efficiencies. A series of 20 deposits on 4-inch-diameter cathodes was produced under simulated production operation. The average current efficiency, based upon a divalent ion, was 72 percent with 11 1/2 pounds of metal produced per cycle of operation - 98.8 percent of which had a Brinell hardness number (B.h.n.) of 80 or less.

Jan 1, 1959

By T. L. Dobecki

As a means of demonstrating the effectiveness of reflection seismology in determining continuity of coal seams, three U. S. field projects are reviewed. The three projects involve coals of varied thickness (2-14m) and age (Pennsylvanian to Eocene) from three coal areas of the U. S. (Pennsylvania, Wyoming, and Washington). Each project also employed its own particular seismic technique, recording system, and seismic energy source although all are considered state-of-the-art, high resolution, digital seismic surveys. Project 1 (thin, Pennsylvania coal) sought detection of sand channels using dynamite and standard in-line (2-D) seismic technique. Project 2 (thick, Wyoming underground coal gasification) involved a gas-explosion (Dinoseis) source with areal (3-D) acquisition methods. Project 3 (thick, Washington underground coal gasification) employed a shotgun-type source and standard in- line methods. Data processing was handled by different contractors for each project. Each project was successful in accomplishing its own particular objective; however, data quality and interpretation seem to be more a function of thickness of the target seam, complexity of the overburden, and processing contractor than a seismic source, acquisition scheme (2-D versus 3-D), or recording instrumentation.

Jan 1, 1981

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By B Dunstan, F Wirfiyata

PT Newmont Nusa Tenggara (PTNNT) operates the Batu Hijau copper and gold mine and process plant on the island of Sumbawa, Nusa Tenggara (Barat)  NTB, Indonesia. The plant consists of a nominal capacity 120 000 t/d conventional semi-autogenous ball milling crushing (SABC) circuit followed by sulfide flotation to produce a bulk copper concentrate for sale. Process control is effected by a plant wide distributed control system that overlays an extensive integrated programable logic controller (PLC) framework. The system is enhanced by a supervisory expert control system.Since plant commissioning in September 1999, over US$4 million has been expended as part of a systematic continuous improvement approach to optimise plant control performance. Works completed to date include: redesign and upgrade of architecture of the control system to ensure long-term system reliability, security and upgradeability and to provide a suitable platform for advanced control; integration of supervisory and advanced control tools, techniques and instrumentation; and implementation of sound network communication and plant data reporting tools. This paper outlines the evolution of process control and associated systems and tools that contribute to successful operation and ongoing performance optimisation at Batu Hijau.

Jan 1, 2009

By Lloyd A. Morley

Proposed advantages and disadvantages of low-voltage shielded trailing cables are formulated utilizing the literature and industry sources. A partial analysis of these proposed advantages and disadvantages is completed through a review of the literature. Cable costs are assembled from mine operators, cable and splice manufacturers, and actual cable purchases. To confirm each advantage and disadvantage, an underground test site is established, and testing is performed here and in the laboratory. All testing procedures are completely described. The results of this investigation are reported and used to formulate recommendations attendant to low-voltage shielded cables. Suggestions for installation, handling, and maintenance are presented.

Jan 1, 1977

By Hae-Moon Choi, Sang-Don Lee, Chang-Ha Ryu

The purpose of the study presented in this article is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing in Korea. Long-hole blasting was tested in rock mass whose RMR value is over 60.The blasting results were evaluated by measuring degree of fragmentation, advance rate,muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a two-lane highway tunnel.

Jan 1, 2006

By I M. Platten

Narrow reef gold deposits are generally less than 4 m in width and relatively complex geological phenomena. They often display variable geometry, attitude, continuity and internal architecture. Economic grades are mostly restricted to specific structural domain(s) and localised within discrete ore shoots that have a nuggety internal grade distribution. On account of the often extended history of geological events, the specific factors localising gold-rich domains are likely to be unique to a particular mine or even reef. These features lead to a high resource risk and require careful management during both evaluation and mining. The gross form, location and global continuity of gold reefs can generally be determined from surface diamond drilling leading to the definition of Inferred Mineral Resources. It is likely that for the definition of Indicated and Measured Mineral Resources underground development and/or close- spaced diamond drilling will be required. Understanding geometry and continuity permits the resource to be more effectively managed, lowering risk/uncertainty. This in turn will allow for well-informed financial and operational decisions. Most importantly, project expectations and milestones can be set at achievable levels.

Jan 1, 2008

By Frederick C. Trutt

Research performed on arcing faults and their interaction; with electrical insulating materials within coal.-mine power-system enclosures is described. This work was performed at The Pennsylvania State University from 1 December, 1976 through 30. November, 1977. Results presented are interim in nature and future research is planned to integrate the simulations which have been constructed, as well as to apply developed experimental procedures to the evaluation of electrical insulating materials for use in coal-mine enclosures. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of an arc model based upon thermal-arc plasma properties so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when an arc interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation.

Jan 1, 1977

By V. E. May

Has your organization adopted Six Sigma as part of their Performance Improvement strategy? What about Lean manufacturing or Lean Six Sigma? If you already have any of these business process improvements in place where will you go next? In this article we will focus on transforming your organization beyond Lean Six Sigma to the next level of performance. In the future companies can take another quantum step forward by combining Lean Six Sigma with advanced Root Cause Analysis (RCA). The value of taking this natural progression on the way to achieving new levels of organizational excellence is presented.

Jan 1, 2011

Papers presented at a U.S. Bureau of Mines (USBM) technology transfer seminar describe the causes of violent material failure in U.S. mines, measurement techniques for monitoring events that result in violent failure, and mitigation techniques for controlling failure. Specific factors contributing to violent failure are identified on the basis of geotechnical monitoring in 16 U.S. hard-rock and coal mines and on statistical analyses of 172 coal bump events. New monitoring and analysis techniques developed as tools for assessing violent failure; geotomographic methods that provide new capabilities for the study of material failure and stress changes over large areas; and seismic methods for determining source locations, calculating energy release, and determining source mechanisms are described. Fair correlations have been established among seismic parameters, elastic stresses, face support load, and violent events. USBM studies have identified the advantages using both yielding and stable pillars for coal bump control. A computer program has been developed as an aid for selecting room-and-pillar layouts. The practical aspects of implementing a destressing program is outlined for coal mines, while the importance of mine orientation and timely support installation in controlling buckling-type failure is identified for hard-rock mines.

Jan 1, 1995

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By Ronald O. Harma

Iron ore pellets made from concentrates produced from low grade iron ores are the primary iron bearing feedstock for iron making in North American blast furnaces. Steelmakers are demanding increasingly higher quality to provide for improved blast furnace productivity, efficiency, product quality and environmental compliance. Unfortunately, this higher quality iron ore product must be produced from the vast deposits of low grade iron ores that are becoming increasingly poorer in quality with regard to mineral liberation and ease of concentration. Since some of these low grade iron ores require grinding to as fine as 90% -500 mesh (25 microns) for liberation and since more of the silicious gangue and other minor undesirable constituents must be removed to provide the higher quality, we have come to depend on flotation to do the added work. Flotation technology and other preflotation unit operations must improve to meet these increasing demands. In many cases, flotation equipment, reagents and circuit operating performance have improved little during the last two to three decades. Mechanical flotation cells have grown from 14 cubic meters (500 cubic feet) to over 84 cubic meters (3000 cubic feet) to help reduce capital and operating costs; however, flotation metallurgical performance has not improved, Column flotation has only recently shown promise in improving metallurgical performance for iron ore rougher flotation. Previous column flotation success was mainly in scavenger and cleaner flotation steps for treating minerals other than iron ore. Although some new flotation chemicals have been developed for removal of silica and other minor constituents under widely varying mineralogical scenarios, recovery of iron mineral has not improved. The operation and control of flotation circuits have become more challenging because of the increasing workload on flotation. Better sensing, process control and operation of flotation circuits are essential as we go forward. Iron ore upgrading by flotation can be classified into either anionic or cationic methods. Anionic flotation of either iron oxide or silicious gangue is accomplished by collector type, pH control and selective chemical activation . Similarly, cationic flotation of silica or iron oxides is accomplished by collector type, activation and/or pH control. Removal of other minor constituents is achieved by using specialty chemicals under controlled conditions for preflotation, co-flotation or post flotation steps. Generally, anionic flotation is used for floating cleanly liberating crystalline oxidized iron ores such as hematite, specularite and martite. Earthy and hydrated oxides such as hematite and geothite can be upgraded with either anionic or cationic collectors after controlled dispersion of slimes or prior removal of slimes. Anionic flotation of silicious waste can be achieved by calcium activation of silica. For magnetic iron ores small amounts of locked silica particles (middlings) can be removed by cationic silica flotation, which is the only method in commercial use in North America today. Historically the efficiency of these iron ore flotation processes has been restricted by the loss of fine iron particles (minus 500 mesh) to the tailings product. New technology is required to overcome this loss and improve overall flotation performance. Development of technology for more selective separation of silica and other minor undesirable constituents from iron ore will provide both quality and cost benefits to the iron and steel producers. Development of future iron ore production in North America will face stiffer technical challenges. These new and undeveloped iron ore deposits are largely oxidized (non-magnetic) and by nature contain more slimes and other undesirable constituents. Unless other new technology evolves, flotation will be the major treatment process required to upgrade these difficult low grade iron ores.

Jan 1, 1993

By William P. Lohden

INTRODUCTION It is recognized that, for a variety of reasons, some companies in the mineral industry today are by no means cash-rich and, in fact, are reporting a growing proportion of long-term debt in their capital structures. A review of recent balance sheets of small, medium-size, and some larger companies, indicates that a fair number still have substantial positions in cash equivalents such as U.S. government issues and other short-term money market instruments. In part, this paper concerns itself with companies which have sufficient cash and equivalents and/or cash generation to internally finance mining projects or expansions but which, for some reason, choose to borrow funds. Misconceptions which appear to frequently underlie so-called "leveraging" decisions are explored in this paper. Also considered arc' those circumstances under which any company, including one that is cash rich, should consider borrowing for a project in an amount beyond what would otherwise be necessary based upon its internal financing ability. I do not attempt to cover the raising of equity capital in public markets in this paper. OVERALL RETURN ON INVESTABLE CASH If you approach an individual with an investment which can be financed from savings, or by borrowing at a rate higher than one is earning on savings, that individual will quickly tell you that to pay interest at a rate higher than is being earned on savings would reduce overall income. Assuming that additional investment opportunities are not currently being considered, the individual concludes that a draw-down on savings, leaving a cushion for contingencies suited to individual circumstances, is the correct financial decision. For reasons discussed later, the simple mathematical logic leading to this conclusion tends to become obscured at the corporate level. When Leveraged Studies Are Inappropriate or Premature Surprisingly, I have heard of a number of companies that could afford to finance an investment solely with internal funds, which have made DCFROR (i.e. discounted-cash-flow rate-of-return) studies not only on a 100% equity basis but also on a leveraged basis. Certainly, a leveraged study would be appropriate if additional projects were competing for more capital than was available internally. Often, however, other projects are not far enough along to warrant a leveraged study and there is some danger that a project may be undertaken because it has an estimated acceptable rate of return, on a leveraged basis, that is not ultimately earned because some of the other projects are postponed or abandoned and borrowing is less than expected. For the above reasons, until it has been determined that (1) borrowing is a reasonable certainty for a particular project and (2) the timing and amount to be borrowed has been determined within a reasonable range of accuracy, I believe it is inappropriate and misleading to calculate DCFROR for a project other than on a 100% equity basis. Even when there are several projects currently competing for funds and borrowing will be required to finance one or more of them, using the common yardstick of calculating DCFROR on a 100% equity basis is a safer method to initially evaluate and compare the attractiveness of the projects. Many companies, whether they would have to borrow or not, will reject projects that on a 100% equity basis do not meet their minimum rate of return standards. Some companies which have to borrow will undertake a project provided the project's DCFROR on a leveraged basis meets its minimum return standards. The danger of this approach is that even moderate shrinkages of estimated cash flows could plunge return below

Jan 1, 1985

By V. J. Driscoll

A method is given for checking pore volume reserve estimates and transient water inflzix factors utilizing early well performance. Principal applications are based on the observation that there is a convenient transient time-range in terms of well spacing in which observed pressure drop will give a good indication of fluid-in-place. Primary quantity determined is a porosity-feet value applicable in the vicinity of an observation well. Checks on porosity or net pay thickness and permeability values also are obtained. These are particularly valuable in improving quality of interpretive factors entering into pore-volume reserve determinations for larger fields. In smaller fields, direct determination of total field reserves and approximate location of boundaries may be made in some cases. Well interference and production data plus a build-up curve on the observation well are needed. The build-up curve may be taken at any time. Field applications are given. The method can be applied with the completion of the second well on a new discovery or to older reservoirs by major changes in withdrawal rates from a local area. Appropriate test length permits results to be obtained with equal accuracy on widely spaced wells. Criteria for optimizing test conditions are given. Provision is made for various boundary and well effects including incomplete observation well build-up. INTRODUCTION Due to low quality data, initial pore volume reserve and water influx estimates may often vary by a factor of two or more from results obtained at a later date. Unfortunately, by conventional methods, more reliable answers from performance usually are not available until after most significant economic decisions have been made. Furthermore, in older reservoirs, uncertainties may still exist as to original oil-in-place, recovery factors and residual oil saturations due to incomplete or inaccurate performance data. This paper outlines situations and appropriate arrangements of basic transient theory whereby well interference data can be utilized to improve the quality of estimates under certain conditions. In addition to production data on offset producers, key information required is a measured pressure drop at an observation well, corrected for any incomplete build-up due to previous production, plus a formation capacity value derived from a conventional pressure build-up plot on the observation well. The method, as outlined, is strictly applicable only to a horizontal single-layered system of uniform rock characteristics containing a homogeneous fluid of low and constant compressibility. However, under the set of test conditions devised, requirements can usually be relaxed so that it should be applicable to most low permeability gas, water and undersaturated oil reservoirs. This is an area where more reliable information is certainly needed. BASIC CONSIDERATIONS A, B, C and F as subscripts or in the text refer to producing Well A, observation Well B, a more remote producing Well C and field boundary F. Combinations such as AB refer to distances and dimensionless times in terms of distances between these points, while single letters refer to distances and dimensionless times in terms of the well-bore or field radius. Equations covering definitions of quantities and complex situations are given in the Appendix. Key equations in practical units are given in Table 2. Transient Pressure Behavior Fig. 1 illustrates pressure drop at Point B with time due to initiation of a constant rate of withdrawal from Point A. This is shown as since a quantitative under-

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007