Search Documents

By M. B. Riordan

A surface indicating pressure, temperature and flow instrument that ernploys variable frequency sensing elements has proved useful in evaluating flow characteristics of wells. Relative productivity of individual oil and gas sands in a given well can be analyzed at several back pressures. The variable frequency sensing elements are an improvement in sensitivity and accuracy and make possible observation of temperature and pressure variations that have not been possible heretofore. The surface indicating featuere results in a more direct approach to solving problems and eliniinate; many assumptions. All three subsurface factors are evaluated, and correlation between them results in a direct means of analyzing reservoir. and well conditions. Surveys have been used to evaluate well performance. locate gas entry In high ratio wells and to investigate gas injection and water flooding conditions. INTRODUCTION In a flowing well that is open to a multiple number of producing sands with varying characteristics. it is valuable to know which sands are producing fluid at a given back pressure and in what relative quantity. Core studies could qualify an interval as productive, and reserves would be computed on this basis. Unless the well is produced so that the interval does contribute. irreparable damage to the interval can occur. It is generally accepted that the optimum condition of pro-

Jan 1, 1951

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

By M. B. Riordan

A surface indicating pressure, temperature and flow instrument that ernploys variable frequency sensing elements has proved useful in evaluating flow characteristics of wells. Relative productivity of individual oil and gas sands in a given well can be analyzed at several back pressures. The variable frequency sensing elements are an improvement in sensitivity and accuracy and make possible observation of temperature and pressure variations that have not been possible heretofore. The surface indicating featuere results in a more direct approach to solving problems and eliniinate; many assumptions. All three subsurface factors are evaluated, and correlation between them results in a direct means of analyzing reservoir. and well conditions. Surveys have been used to evaluate well performance. locate gas entry In high ratio wells and to investigate gas injection and water flooding conditions. INTRODUCTION In a flowing well that is open to a multiple number of producing sands with varying characteristics. it is valuable to know which sands are producing fluid at a given back pressure and in what relative quantity. Core studies could qualify an interval as productive, and reserves would be computed on this basis. Unless the well is produced so that the interval does contribute. irreparable damage to the interval can occur. It is generally accepted that the optimum condition of pro-

Jan 1, 1951

By Smele J. S, Dawes W. D

In recent years there has been a trend among mining companies to diversify exploration and development away from the countries that have dominated mining activity for the latter half of this century. With some exceptions, this trend is accelerating and is a function of the recognition that many parts of the world, with no previous exposure to modern exploration, are endowed with considerable mineral potential. In addition coincident with changing political and economic circumstances, many countries have recognised the benefits of attracting international mining investment and have radically changed policies, fiscal and legal regimes so as to encourage exploration and mining. Some countries, however, have not readily accepted mining for cultural or social reasons and have yet to make effective changes to mining legislation. For historical reasons, other countries may have little or no direct experience of western economics, nor may they fully recognise the need for stability and competitive fiscal and legal systems to attract foreign investment. Not all ventures in new countries have been commercial successes and there have been some lamentable and recent lapses from grace. Company strategies, company standards and management objectives can also vary widely from company to company. What may be an acceptable risk or rate of return for one may be completely

Jan 1, 1997

By T. H. Jeffers

Significant amounts of cobalt are present in readily accessible spent copper leach solutions. The Bureau of Mines investigated the feasibility of extracting cobalt from these solutions in a multiple-compartment ion-exchange (MCIX) column. The effects of aqueous flow rate, resin flow rate, column height, and compartment height on cobalt extraction were determined. Cobalt extractions of 92 pct or higher were achieved at solution flow rates of up to 5.5 gpm/ft of column cross-sectional area and an aqueous-to-resin flow ratio of 40:1. Overall cobalt extraction increased as the column height increased, but cobalt extraction per unit of length was more efficient in 8-and 12-ftco1umns than in an 18-ft column. Solvent extraction procedures were utilized to purify and concentrate the MCIX column eluates and produce a cobalt sulfate solution containing 70 to 80 giL Co. Metallic cathodes containing over 99 pct Co were e1ectrowon from this solution. Zinc, nickel, and copper byproducts were also recovered during processing of the ion-exchange eluates. Estimated total capital cost for a commercial-scale 10,000 gpm of a spent leach solution containing 26 million. With credits for zinc, nickel, and copper estimated net operating cost was $9.36/lb Co.

Jan 1, 1987

By T. F. Anstett

The Bureau of Mines investigated the availability of platinum from known major deposits in market economy countries. Fifteen of these deposits contain demonstrated resources totaling 302 million troy ounces of platinum. Detailed geologic, engineering, and cost evaluations were performed on each deposit to determine its potential for platinum production. There are large amounts of demonstrated platinum potentially available from market economy deposits that were not analyzed owing to lack of adequate data or to technological limitations. These include 297 million troy ounces contained in the UG2 and Platreef of the Bushveld Complex, South Africa. This analysis indicates that about 11 0 million troy ounces (2.3 million ounces annually) of platinum are potentially available at the January 1980 producer price of $420 per troy ounce, nearly all from South Africa. An additional 85 million troy ounces occurring in Zimbabwean deposits would become available only through more than a quadrupling of that price. In order to meet projected world demand of 3.5 million troy ounces in 1990, platinum price may have to increase. Only one domestic deposit, the Salmon River in Alaska, is capable of producing platinum at $420 per troy ounce. Regardless of price, at assumed production capacities, domestic deposits could supply less than 10 percent of annual U.S. requirements.

Jan 1, 1982

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975

An oxide ore heap (80,000 ton assaying 2 per cent copper) and a sulphide ore heap (300,000 ton assaying 1·7 per cent copper) are being leached in series in a closed circuit system. The ore is friable and weatherseasily giving severe percolation problems. These were eased by applying liquors at 235 gal/min to trenches 2 ft wide and 6 ft deep along the full length of the heaps.Cementation recovery was improved from 20 per cent to over 80 per cent by regular intermittent agitation of the iron using a back hoe unit.Liquor pH is controlled by acid addition, and iron content is controlled by a bleed-off set according to predictions made from a pH-Eh diagram drawn for the liquor components. These controls, together with acyclic wetting and draining procedure, have raised production from 6 ton/week to 10 tdn/week of 80 per cent copper.

Jan 1, 1968

By Valerie (Wollet) Rebar

Successful execution of fast-track projects is an arduous task at best. Effective and organized management, a comprehensive technical design with an independent check-and-balance system, and optimal schedule components all play major roles in project success, regardless of the required timeline. However, a fast-track schedule intensifies the significance of each of these elements due to the heightened time constraints.

Jan 1, 2008

By I. Mihajlovic

This paper investigates a potential method for arsenic removal from copper concentrates using hypochlorite leaching. The problems concerning pyrometallurgical processing of copper concentrates with high arsenic contents are discussed. A possible solution to the problem by leaching of natural enargite crystals with sodium hypochlorite under alkaline oxidizing conditions, with enargite converted into crystalline CuO and the soluble arsenic forming AsO43-, was experimentally investigated and results are presented. Kinetic parameters were calculated for enargite leaching, using a model-free approach. Advanced isoconversional methods were used to investigate the dependence of activation energy (Ea) on reaction rate (a). Keywords Enargite, copper concentrate, isoconversional method, kinetics, activation energy.

Jan 1, 2011

By Hamid-Reza Manouchehri

Mining & Sustainability? A Paradox?! ? Production: gradually or exponentially increasing (giant mining) ? Ore Grades: gradually declining, ? Open Cut Mining: now widespread, likely to be sustained in the future though the long-term is hard to predict as new mineral deposits are likely to be deeper ? Waste Rock / Overburden: increasing rapidly, likely to be sustained in the future and closely linked to open cut mining, especially for coal and base metals ? Economic Resources: commonly increasing but some remain stable or gradually declining, future is linked closely to exploration, technology and economics; Increasing population, changing life style and technology development, ultimately result in sustainability in mining industry to hang in the balance and continue.

May 1, 2013

By Matthew Janes

Statnamic load testing is becoming widely accepted as a method to quickly and economically determine the load-deflection behaviour and ultimate static resistance of high capacity deep foundations. Strain instrumented large diameter bored shafts were tested at four locations for the federal and state Departments of Transportation in the United States. Tests were conducted vertically (to 30 MN) and laterally on the shafts and, in some cases, testing was completed over water. Instrumented shaft test results provided shaft load distribution with depth and shaft shear transfer stress throughout the soil stratum. Shaft end bearing and ultimate end bearing stress values were provided. On two projects, Osterberg load cells provided comparative static data for skin friction and end bearing. Correlations between Statnamic derived static load-displacement results and Osterberg load-deflection results are very good. Statnamic lateral load test results were correlated with static lateral results in addition to providing useful dynamic response and damping data.

Jan 1, 1996

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By P Geddes, K Grohs, C K. McKenzie, M Morrish

Low grade surface gold mining at the Acacia Resources, Union Reefs Gold Mine in Australia's Northern Territory, involves the excavation of benches in three slices after blasting. Blast patterns span zones of high and low grade ore, as well as zones of waste, and selective excavation is required in order to maintain economical head grades for the carbon-in-leach processing plant.

Jan 1, 1998

By E Nettleton, A Melkumyan

A probabilistic system for autonomous tracking of excavated ore in mining would be highly valuable. Currently, mine sites can have a vast array of sensors; examples include excavator load cells, bucket volume estimators and haul truck strut pressures which can be used to gather information about the excavated ore at different locations. These sensors can be utilised efficiently to increase the accuracy of mine estimates by introducing a real-time ore tracking system. This requires the introduction of a probabilistic ore tracking framework to consistently fuse information from any sensor input. Current modelling practices are manually intensive, deterministic (no recognition of the quality of data) and generally not a complete end-to-end system. This paper will provide a novel method for tracking extensive ore properties (mass, volume) and intensive ore properties such as chemical composition (eg Fe per cent, SiO2 per cent, Al2O3 per cent). This method is proved to ensure that correct correlations between states are conserved as material is transferred, combined and/or separated at different locations with any configuration of sensor inputs. This ensures that consistency of estimates is maintained and other benefits such as real-time probabilistic reconciliation can be implemented. A method for combining material of different mass and chemical compositions is also developed to enable accurate and efficient operation of the system. Representative experiments on a small-scale and a larger field trial which mimic the mining processes of excavation, haul and unload to ROM Stockpile will be used to verify the approach.

Sep 26, 2011

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023

Compressive crushing is applied in crushing plants used in mineral, mining, and aggregate in-dustry for fragmentation of rock materials. From a global perspective, the total volume of crushed rock is massive and corresponds to several billion tons. All societies have to fulfil a daily need of rock material products and its derivatives such as metals and minerals. The business for metals and minerals is global while the aggregates production is mainly a local industry. This paper presents a broader overview of optimisation with respect to product yield, use of natural resources and energy consumption. High level plant optimisation of compressive crushing plants is covered as well as real-time optimisation and optimisation of single production units. Each of three optimisation areas are presented and a discussion around how these three areas will be able to communicate with each other is given. Several models, e.g. process performance behav-iour with respect to wear, as well as fitness functions can be common for all three areas. Well-defined and representative fitness functions are of the utmost importance in order to assure that the optimisation results reflect the production targets. It is concluded that great benefits can be achieved by linking together different areas of optimisa-tion. The future for compressing crushing lies, without a doubt, in tailored processes both with re-spect to machines optimised for each customer, plant parameters and operation routines as well as an on-line adjustment, which takes into account current information and control possibilities.

Jan 1, 2014

By R. K. Koch

The Bureau of Mines developed a zircon sand molding process for static casting of small titanium or zirconium shapes. Castings with unfinished weights up to 3.5 kg (7.7 lb) were produced in an inductoslag furnace and castings up to 7 kg (15.4 lb) were poured in a consumable electrode skull-casting furnace. Molds and cores were made by ram-molding, foundry-grade zircon sand (AFS gfn 93 to 95) bonded by grade D waterglass and tempered with water. Molds and cores were cured either at 250° C (482° F) or 900° C (1,652° F). Castings from the higher temperature molds broke cleanly from the sand while the lower temperature molds produced castings that had to be cleaned by sand-blasting. However, low-temperature cured molds and cores have a number of advantages as follows: (1) A faster, less energy-consuming curing cycle is used; (2) expended cores are water soluble which greatly facilitates core removal; and (3) enough of the binder in crushed expended molds is reactivated by temper water so that the molding mix can be reused five times without any fresh binder additions and up to twenty times without exceeding a total cumulative binder addition of 52 ml/kg dry sand. Crushed used molds that had been cured at 900° C had no detectable binding strength when mixed only with temper water. A large number of oxide and silicate mold washes were studied for improved casting integrity. The most effective wash found for zirconium or titanium casting was monoclinic zirconia (325 mesh).

Jan 1, 1977