Search Documents

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By C Mason, A Littleboy

This paper presents the results of a large scale survey of The Australasian Institute for Mining and Metallurgy (AusIMM) membership. This survey aimed to understand and define the key issues and drivers that AusIMM members perceived would shape the development of the Australian minerals industry over the next 20 - 30 years. Nine hundred and fifty-nine participants rated the importance of 11 issues and six drivers (generated from interviews with AusIMM members), and 236 of these participants also provided qualitative descriptions of the future. Issues were defined as problems or opportunities for the minerals industry that may be controlled or influenced by the industry, while drivers were defined as those factors that will influence the direction of the industry that are not within the control of the industry. The quantitative data revealed that the top four issues, in order of their perceived importance to the Australian minerals industry, were: investment in exploration, workforce, health and safety, and innovation. The top three drivers in order of their perceived importance, were: economics of mining, global context and Australian society. While the top four issues were largely consistent across professional groups examined, metallurgy and mineral processing professionals rated water inputs and energy inputs significantly higher than the other professional groups. For the list of drivers, there was strong agreement regarding their ranked order of importance across the professional groups examined. Within the qualitative data, however, a single issue (technology) and a single driver (economics of mining) dominated participantsÆ descriptions of the future. These findings provide important input into a broader program of scenario development for the Australian minerals industry being undertaken by CSIRO and its partners. The results of this study demonstrate the importance of using a mixed methodology in generating these inputs to understand more fully how important stakeholders view the future and the factors that will shape it. The results of this study are also discussed with respect to the role that CSIRO may play in facilitating the exploration of uncertainty around the future of the Australian minerals industry.

Jan 1, 2009

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By W J. Botha

The Palaeoproterozoic Transvaal Supergroup in the northern Cape Province of South Africa hosts high grade (>60 per cent Fe) hematitic and specularitic iron and manganese mineralisation. The mineralisation is primarily exposed along the western margin or in the central part of a major interference fold structure known as the Maremane dome. The bulk of South AfricaÆs iron ore production is currently provided by two active mines, Kumba Resources megaton Sishen iron ore mine on the northern end of the dome, and the smaller Assmang Beeshoek mine on the southern closure. The undeveloped Sishen South deposit, which contains ~400 Mt of high-grade hematite ore, is located approximately 9 km towards the southwest of Postmasburg. It forms a linear extension of the Beeshoek mine and as such contains comparable laminated, breccia and conglomeratic iron mineralisation. The Transvaal Supergroup sediments were deposited in two distinct fault-controlled basins on the Archean Kaapvaal craton. Basement rocks in the western Griqualand West basin are formed by a carbonate platform sequence (Campbellrand Subgroup), which is overlain by a thick sequence of banded iron formation of the Asbesheuwels Subgroup. A major unconformity separates these rocks from the red-bed Gamagara Formation, which is correlated with the base of the Olifantshoek Supergroup. Diamictites and lavas of the Postmasburg Group have been thrust over these units from the west. The mineralisation process is related to regional scale supergene iron enrichment of Kuruman banded iron formations along the unconformity. During regional tectonism associated with the Kheis orogeny (2400 - 1700 Ma) the Maremane dome was uplifted, and the basal dolomite units thus exposed to erosion and karstification. The overlying banded iron formations collapsed into karst sinkhole structures where leaching of silica and enrichment of hematite occurred. Although the exact mechanism of the mineralising process remains unclear, karstification preserved components of the original concordant laminated and massive ores. These ores were subsequently eroded and deposited as conglomeratic and gritty ores down-dip of the Maremane dome in alluvial fan systems. A thin veneer of recent calcrete or Tertiary Kalahari clay beds masks the subsurface geology and most of the orebodies, thus ground geophysical gravity surveys proved excellent exploration tools to penetrate the surficial cover. These surveys were used extensively for delineation drilling and to deduce the subsurface geology and structural development of the area. Finally Sishen South orebodies were modelled with ModelVision software in an attempt to obtain an exploration template for the surrounding area.

Jan 1, 2005

By O. M. Schaus

The following is a description of the methods employed at the Eureka-Asteroid mine, which is situated on the Gogebic range, at Ramsey, Mich. The mime is operated by the Castile Mining Co. under the direction of Oglebay Norton & Co. This paper has been prepared in accordance with an outline furbished by the United States Bureau of Mines, and in one of a series, on mining methods and costs covering the principal minim operations throughout the United States. ACKNOWLEDGMENTS The author acknowledges the assistance of the mining organization of the Castile Mining Co. in the preparation of this paper.

Jan 1, 1930

By Boyd Dudley

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By G. L. Oldright, Virgil Miller

"ACKN0WLEDGMENTSThe data given in this paper were collected at the Bunker Hill smelter through the courtesy of Stanley A. Easton, the vice-president and general manager, Frank M. Smith, the smelter director, and with the assistance and cooperation of A. F. Beasley, the smelter superintendent, and his staff members.THE BLAST FURNACE AND PLANTThe general lay-out of the recently built (1917) Bunker Hill plant has been given in the technical press in articles that were cited in Report of Investigations 3088. In addition it may be noted that the description of an ideal smelter given by Riddell 5 a year later fits the Bunker Hill smelter very well, with some changes, such as the location of the stack, made necessary by topography. For purposes of this article on the blast furnace it may suffice to state that the plant is one of the ""side hill location"" type. The various successively lower benches may roughly be considered as made for (1) the stack, (2) Cottrells and bag houses, (3) Dwight and Lloyd sintering machines with the equipment or bins for handling or mixing the feed and storing the finished product, sinter, and (4) the blast furnace feed floor with a slightly rising gradient to the bottom of the bins for sinter, feed, and take. The lowest bench (5) might be considered that of the blast furnace tapping floor at which or at appropriately slightly lower elevations are located the units for softening, refining, and treating precious metals, and for casting and loading lead. A very careful study of grades was made in order to be able to handle the products easily. All units were left with at least one end open to permit expansion of the plant, it desired, and each unit was separated from the other, evidently so that the operators on one level would be annoyed as little as posssible with the products made on another."

Apr 1, 1931

The Department of Interior, U.S. Bureau of Mines performs the task of estimating the quantity of coal reserves existing in each state on a county by county basis. As a part of Information Circular 8655, the Bureau of Mines established the criteria for the uniform estimations of coal reserves and listed the most recent estimates of coal reserves by county and by seam. At the same time however, the Bureau recognized that these figures represented the upper bound with regard to the estimated actually usable or obtainable reserves. Recovery of these reserves are subject to the mining methods used and to the resolution of such problems as the use of poor quality coal and competition provided by conflicting land use. These problems, in practice restrict the recovery of the estimated quantities of coal reserves listed in IC 8655. Another impact, the subject of this manual, is the impact resulting from previous mining activities. In particular, many of the reserve seams included in the reserve estimates overlie or underlie mined-out coal beds. Portions of these reserve seams may therefore be unmineable or at best may have a reduced quantity of extractable coal. In order to improve the accuracy of the coal reserve base estimates, the Bureau of Mines funded an effort1 to develop a systematic methodology for estimating the coal loss associated with the impact of previous mining activity. The coal loss calculation model (CLCM) described in this manual is a result of that effort and addresses the percentage of coal loss in reserve seams due to previous overmining or undermining.

Jan 1, 1976

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

By G. L. Fisher, R. H. Geils

The effect of small amounts of columbium (<0.01 to 0.10 pct) on the ?-a transformation occurring during the continuous cooling of a low carbon Ni-Cu steel was investigated. Dilatometer specimens were aus-tenitized at 950" and 1068?C and cooled at 17? and 375 C° per min. Columbium caused a marked depression in the ?-a transformation temperature except when cooling at the slower rate from 950°C. The effec of columbium on the transformation temperature was greater the higher the austenitizing temperature and rate of cooling. A maximum depression of 92 C" was observed. Metallographic examination of specimens of <0.01 and 0.07pct Cb steels heated at 1200°C for 1 hr and cooled at various rates showed that columbium had a major effect on the ferrite morphology. The fer rite in the columbium -free steel remained equiaxed at cooling rates as high as 440 C? per min while the columbium-bearing steel exhibited mixed structures o equiaxed and bainitic ferrite at cooling rates as low as 130 C° per min. The ? grain boundaries in the columbium -free steel provided the ferrite nucleation sites in rapidly cooled specimens. There was a complete absence of nucleation at these sites in the colum bium-bearing steel. It is concluded that columbium depresses the transformation temperature by suppressing ferrite nucleation at the austenite grain bound-aries. In this respect the effects of columbium are analogous to those of boron in low C-Mo steels. It is well known that small columbium additions can substantially strengthen plain carbon steels. As little as 0.02 pct Cb can increase the yield strength of mild steels by 10,000 psi.1 A fine precipitate of CbC has been observed in columbium-bearing steels2 and is generally thought to be responsible for the strengthening. Little attention has been devoted to the effect of columbium on the ?-a transformation. Webster and woodhead3 have studied the effect of columbium on the isothermal proeutectoid ferrite reaction in mild steels. They found similar transformation behavior in steels both with and without columbium additions. However, as the austenitizing temperature increased, the incubation time for the start of the ferrite transformation became longer in the columbium-containing steel. Morrison1 found that the addition of 0.03 pct Cb to a C-Mn steel lowered the transformation temperature by 50 C° during cooling from 1200°C at a rate of 80 C" per min. The strengthening effect of columbium has recently been utilized in an age-hardenable, low-alloy steel containing copper and nickel.4 A small amount of columbium has a substantial effect on the as-rolled strength of this steel. By increasing the columbium level from <0.01 to 0.13 pct the as-rolled yield strength is increased by 15,000 psi. Columbium also significantly lowers the ?-to-a transformation temperature of this steel during continuous cooling from the austenitizing temperature. Because of the low carbon level in this steel (0.05 pct max), it is almost entirely ferritic. Thus, it offers the opportunity of studying the effect of small columbium additions on the proeutectoid ferrite reaction. Of particular interest in this study was the reason for the marked lowering of the transformation temperature by columbium during continuous cooling. EXPERIMENTAL PROCEDURE Materials. The compositions of the steels used in this investigation are shown in Table I. The steels were 30-lb air induction melts. They were forged to 4 by 8 by 1 in. plate at 1230°C, air cooled, and then reheated to 1230°C and cross-rolled in two passes to in. plates. Dilatometry. A Leitz Bollenrath dilatometer was used to record the transformation during continuous cooling from two different austenitizing temperatures. The dilatometer specimens were + in. in diam and 2 in. long. Oxidation and decarburization of the specimens was prevented by maintaining a small positive pressure of dry argon in the dilatometer furnace and by plating the specimens with 1 mil of Cu. For the lowest cooling rate, 17 C" per min, the temperature of the specimen was measured with a Pt-Pt 10 pct Rh thermocouple placed in a & in. diam well in the center of the specimen. During air cooling, 375 C° per min, this method of measuring the temperature interfered with the operation of the dilatometer. However, it was found that the temperature of the specimen could be measured accurately by placing a thermocouple in an identical specimen in a holder adjacent to the one being used to operate the dilatometer mechanism. The dilation-temperature curves were recorded on photographic film and then converted to volume percent ferrite-vs-temper-ature curves. The cooling rates obtained with the dilatometer are shown in Table 11. Cooling rates of

Jan 1, 1970

By Sherwin F. Kelly

FRONTIERS of geological knowledge retreated further this past year before an ever-widening geophysical attack, as governments and endowed institutions continued to take an increasing practical interest in the geophysical line of approach to the study of earth phenomena. A year ago I opened this annual review with a brief account of the efforts to discover what formations lie concealed beneath the deep sediments which form the superficial portions of the Continental Shelf off the eastern United States. That work was but the beginning, and 1938 saw its continuation and expansion. With the assistance of a Guggenheim Fellowship, Maurice Ewing pushed his researches in the development of instruments and techniques for deep-sea seismic refraction studies. Ewing&apos;s early refraction profile from the Virginia Capes to the edge of the Continental Shelf has been followed by a similar traverse in Great Britain from the coast of Cornwall to the edge of the Continental Shelf southwest of England. This showed that the thickness of the sedimentary mantle and the rates of slope of the basement surfaces there are comparable to those in the Virginia Cape district.

Jan 1, 1939

By Karl A. Higgins, Michael D. Venezia

The South Capitol Street Corridor Project is one of the District Department of Transportation’s (DDOT) largest projects, and is currently under construction. This case study will focus on the design of the foundation piles for the main spans of the iconic Frederick Douglass Memorial (FDM) Bridge, and will include a discussion of the foundation design evolution from an originally designed alternative foundation system (i.e. coffer dams and drilled shafts), to the current use of driven Large Diameter Open End Pipe (LDOEP) Piles. The paper will provide a discussion of the design methodology used during preliminary engineering and final design, and will highlight insight gained from the extensive load testing program completed to date. The load testing program consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre-production test piles. Specifically, data gathered during the nearly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles. This paper will also discuss limitations of currently accepted industry design methods for predicting the capacity of LDOEP piles, a subject that is also currently being researched by FHWA. The data from this test pile program will help design assumptions for future projects. INTRODUCTION The Frederick Douglass Memorial (FDM) Bridge carries South Capitol Street across the Anacostia River in Southeast/Southwest, Washington, DC, and is owned and maintained by the District Department of Transportation (DDOT). The existing FDM Bridge is nearly 70 years old, serves as a major artery into the city, and has been classified as functionally obsolete. As a result of the condition, age and limitations of the existing bridge structure, DDOT deemed it necessary for complete replacement of the bridge. The replacement project consists of the construction of a new bridge traversing the Anacostia River, as well as the reconfiguration of the Suitland Parkway and I-295 interchanges located at the eastern terminus of the FDM Bridge. Final design and construction services for the replacement project were procured by DDOT through a Design-Build contract. This paper will focus on the driven Large Diameter Open End Pipe (LDOEP) Piles used for support of the main span of the new FDM Bridge which is currently under construction. Discussion regarding the LDOEP Pile design methodology has been included, along with commentary regarding currently available industry guidance related to design and construction of LDOEP Piles. Much insight has been gained during the mostly-completed and extensive load testing program which consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre- production test piles. Specifically, data gathered during the mostly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles.

Jan 1, 2019

By C. L. Burrill

The forecasts presented in this paper constitute an attempt by the writer to predict the pattern of the consumption of petroleum products in the United States during the period of transition from war to peace. Although, in preparing the estimates, secular trends were not overlooked, greater emphasis was placed upon considerations of a cyclical character, or upon influences which might be peculiar to parts of the period. The estimates do not extend beyond the year 1950 because by then conditions in the industry should have returned to normal. The consumption of petroleum products is affected, of course, by changes in the condition of business in general. Before estimates of petroleum consumption could be prepared, therefore, it was necessary to predict the pattern of general business during the period under review, particularly the economic series that in the past have shown the closest relationships with petroleum consumption. It is the writer&apos;s view that business activity in this country (as measured by industrial production) will be higher on the average during the period between the end of the war and the year 1950 than it ever was before during a peacetime period of the same duration. When the war is over, consumers will have saved amounts of money that will be very large as compared with any previous accumulations. There is little question, therefore, as to the financial ability of consumers to purchase goods. The production of many durable consumers&apos; goods, such as automobiles, refrigerators and radios, has been completely stopped since early in the war; also, many semidurable and nondurable consumers&apos; goods have not been available in the quantities or the qualities desired. There is considerable needi therefore, for consumers to purchase goods after the war. The important question is whether consumers will purchase goods in "1arge enough quantities to keep our economy running at a high level. The writer answers this question in the affirmative. The mere existence of very large consumer savings lends considerable support to this view because, with such backlogs of " security," consumers can afford to spend more of their current earnings than they otherwise could. Also, several polls have been taken, which indicate that consumers expect to buy large quantities of a variety of goods. Some of the savings, therefore, probably will go into current consumption. Even though this percentage is relatively small, so that the bulk of the funds accumulated by consumers during the war continues to remain as savings during the period under review, spending should be great enough to start the production cycle and keep it

Jan 1, 1945

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

By Isadora Dias Perez, Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa

The generation of mining waste has been the subject of environmental, economic and social concern. Alternative and sustainable methods of recycling metals technologies are desired. The present work focuses on the application of the ion exchange technique for the extraction of metals contained in a lateritic nickel mining effluent. The Purolite S950 chelating resin was used in the present work because it has the ability to adsorb transition metals present in an acidic solution. The experiments were carried out in a batch varying the pH in the range of 0.5–2.0. 1 g of resin was placed in contact with 50 mL of solution and stirred for 120 min at a speed of 200 rpm and temperature at 25 °C. The results demonstrated that the affinity of the resin varied with pH. The adsorbed metals were only copper, manganese, magnesium and zinc. The most extracted metal was copper, corresponding to 37%, when the solution was conditioned at pH 2.0.

Mar 1, 2018

By C. A. Herbert

Information Circular 6746 reviewed the fatalities in Indiana coal mines. for the fiscal year October 1, 1951 to September 30, 1933. Since then Indiana has changed its fiscal year to the period July 1 to June 30, but as most statistical data on accidents are arranged according to calendar years, the data in this paper are for the last 3 months of 1932 and the calendar year 1933, rather than for the new Indiana fiscal year. Tables 1 and 2 list the fatalities in Indiana coal mines3/ by cause and occupation for the last 3 months of 1932 and for the calendar year 1933. The fatalities for the small wagon mines employing fewer than 10 men are separated from those employing 10 or more men to call attention to the ex- tremely high fatality rate in small mines, largely because the State mining law does not apply to them nor do they come under the jurisdiction of the Indiana mine inspectors; as a result health and safety conditions are ex- tremely bad. During the last 3 months of 1932, 5 (approximately 42 percent of the total) fatalities occurred in the small mines, while for the calendar year 1933, 12 (approximately 32 percent) of the fatalities occurred in them. The Indiana Division of Mines and Kining estimates that these small mines have an annual production of approximately 325,000 tons, or about 4.5 percent of the total coal-mine production of the State. In other words, for these small mines the fatality rate per tons mined during 1933 was about 10 times as great as for the mines employing 10 or more men. Another lamentable feature in connection with the fatalities in small mines is that very few carry any compensation insurance and the owners are not worth enough financially for dependents of victims to collect anything under the common law; as a result, the dependents of those killed usually are left penniless and subjects of public charity.

Feb 1, 1935

By Mikael Calando, Thomas Joussellin

"San Francisco's rapid growth has caused the city to plan for the Transbay Transit Center Project, a visionary transportation and housing project, that will transform downtown San Francisco and the San Francisco Bay Area’s regional transportation system by creating a “Grand Central Station of the West” in the heart of a new transit-friendly neighborhood that will be home to more than 20 new towers rising a high a 1,070 ft. This paper describes the specificities of using advanced diaphragm wall technology, tooling, equipment and installation practices for deep foundation and permanent underground structures. In particular, this paper will emphasize on the urban constraints, geotechnical conditions, and the novel approaches adopted for the construction challenges of the Transbay Transit Center’s Load Bearing Elements, or Barrette PilesPaperThe Transbay Transit Center Project consists of the construction of a new multimodal, five-story Transit Center located in the South of Market neighborhood near the Financial District in San Francisco. The future Transit Center will incorporate nearly 83,000 square feet of retail, a 5.4-acre rooftop park, an extensive public arts program and bus ramps that will connect the Transit Center to a new off-site bus storage facility and the San Francisco–Oakland Bay Bridge. The new facility will accommodate more than 100,000 passengers each weekday and up to 45 million per year. Additionally, the new Transbay Transit Center will replace the since-demolished San Francisco Transbay Terminal, and nearly 20 towers, such as Salesforce Tower, will take advantage of the height increases allowed through the Transit Center District Plan.The approximately $4.5 billion project features a new five-story structure (including two underground stories) and new bus ramps which include a cable-stay bridge. The deep foundations for the pylon of the bridge (Pylon 9) consist of two each 21 ft x 5 ft barrettes (also called Load Bearing Elements in the US) extending more than 180 feet below grade and 10 feet into the bedrock. The barrettes were chosen because of the combination of high loads, significant depth and small footprint. The barrettes are installed using the Diaphragm Wall technology. Nicholson Construction was contracted by Shimmick Construction to install the cable-stay bridge’s foundation elements."

Jan 1, 2016