Search Documents

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

Surface mining of coal is widely condemned as a despoiler of the countryside and wastrel of land and natural resources. Yet the fact has been as widely ignored that the ingenuity of those engaged in developing the methods and equipment utilized in surface mining have made several hundred million tons of coal available for utilities and industry which could never have been mined by any other method. While doing this, the surface mining companies have recovered nearly 100% of the coal in the mining area instead of approximately 50% as is common in underground methods. Efficiency has been increasing constantly, thereby maintaining low cost to the customer. Mining has provided economic health in many areas by virtue of the direct payrolls and by the attraction of other industries to enjoy low cost, dependable fuel supplies. Surface mining of coal generally falls into two categories: contour mining, which is the result of mining in hilly or mountainous terrain where the hillside or slope limits the width of the area which can be surface mined; and area mining, which results from the surface of the land being approximately parallel with the coal seam so that a wide area may be mined in a succession of pits or open cuts.

Jan 10, 1972

By S. Eugene Mills

Twenty-five years ago, when I began my sales life marketing minerals, there was little or no contact between sales people and production people. In those days, it was not uncommon for me, as a salesman, to learn of production problems existing in my company from my customers. Today, in my opinion, any successful mining company must keep production people fully aware of circumstances that effect service to the users of the product. Basically, feldspar is presently consumed by the glass and pottery industries the same as 100 years ago. The consuming public little realizes the origin of so many things they use daily and take for granted. Feldspar is utilized in the glass that contains our Coca-Cola, Pepsi, wines, liqueurs, beer and the assorted gob¬lets from which we drink these lovely brews, the industrial glass upon which all industry depends, the bathroom plumbing fixtures that make life so different from the days of the out-house, the beautiful and durable china we enjoy at mealtime. The electricity we use requires insulators that demand feldspar. In our home ap¬pliances, automobiles, toys and airplanes, we find feldspar. I could go on and on, hopefully soliciting your help in making our taxpaying and non-taxpaying fellow man aware of the burdens he may acquire when unthinking, over-enthusiastic environmentalists foist unnecessary hardships upon the mining industry. Feldspar is marketed primarily sized from 20 mesh to 325 mesh. The glass industry requires feldspar ground 20 mesh to 40 mesh size; the pottery industry requires material from 150 mesh to 325 mesh size. One large glass plant may require up to 100 tons per day and more, whereas a small plant may use less than 5 tons per year. A large pottery plant may require as much as 50 tons per day, a small potter only 500 lbs. per year. The feldspar

Jan 1, 1977

By L. G. Marsh

The manufacture of lubricating oils from wax-bearing crude petroleums involves the removal and recovery of the paraffin wax contained in the lubricating distillates. During this process several intermediate products are formed, among them the mixture of waxes and oils known to the refiners as "foots oil." Because of its complex character, foots oil is little understood, and therefore methods of handling it in refineries are often inefficient. The Bureau of Mines is studying the manufacture of lubricating oils, and during the work has investigated the redistillation of foots oil. This report gives in brief the results of the investigation, and recommendations based upon it.

Jan 1, 1926

By Vernon Taylor

CANADA'S oil production is obtained almost entirely from the Turner Valley gas and oil field, in the Province of Alberta. This field, about 30 miles southwest of the city of Calgary and approximately 115 miles north of the United States border, supplied 92 per cent of production in Canada during 1937. In 1938 considerable development took place in this field and total production for the year amounted to 6,688,716 bbl., an increase of 3,922,146 bbl. over the production in 1937, which increased the percentage of production to approximately 97 per cent of Canada's total. In the British Empire, Canada's production is thus comparable to that of Bahrein Island and Burma, each of which produced approxi-mately 7,800,000 bbl. in 1937, being second to Trinidad's production of 15,500,000 bbl. The total production of the British Empire in that year amounted to 2.07 per cent of the world's total. HISTORY Development of the Turner Valley field commenced in 1913, when a well was started near a gas seepage on the banks of the South Fork of Sheep River in the central part of the Valley. This well found small quantities of a light crude oil in beds of Upper Cretaceous age and pre-cipitated a wild boom in 1913-1914 which ended with the beginning of the Great War in 1914. A small amount of drilling was done in the years from 1914 to 1922 and a few wells found small crude-oil production in the upper sands. In 1922 a few wells were started, including the Royalite Oil Company's No. 4 well (R, Fig. 1), which became the discovery well of naphtha pro-duction from the Paleozoic limestone. In October 1924, this well was completed at a depth of 3740 ft., being approximately 300 ft, in the lime-stone, with an initial flow of 600 bbl. of 72° A.P.I. gravity naphtha and 20,000 M cu. ft. of gas per day. Intense activity was not started until the latter part of 1928, when the Okalta No. 1 well (Q, Fig. 1) was drilled, with an initial production of 500 bbl. of naphtha per day. This well was only 1 ¼ miles from Royalite No. 4, but it was approximately 1300 ft.

Jan 1, 1939

By Robert S. Sokolowski

The future of Materials Processing in Space (MPS) in the Space Station Era is being assured today by a strong coordinated science program which looks to solve these problems, the answers to which serve to underpin the technical foundation upon which future metallurgical and materials processes will be built. The critical link between the product and process development activities that accompany this science endeavor is the "nuts and bolts" hardware that will ultimately operate in the space environment. Ground-based facilities including drop facilities and aircraft provide excellent product development and process concept study tools. Shuttle flights with Spacelab and commercially developed space facilities represent the evolutionary path to Space Station processing facilities. Today the most promising areas of MPS are crystal growth, containerless, and quasicontainerless processing. The unique features of these processes will be highlighted. Finally a more visionary perspective of MPS will be presented that incorporates the limits of today's knowledge with the economic "necessity" of tomorrow.

Jan 1, 1988

By M Ma, W J. Bruckard, C Gontijo, R Holmes

Vale is the largest iron ore producer in the world. Since the 1970s, Vale has been using reverse cationic flotation to remove siliceous impurities from its iron ores. Whilst this flotation process has operated effectively for many years, it suffers from the problems of high reagent costs and high metal loss.In 2010, CSIRO investigated the use of a reverse anionic flotation process for Vale iron ore. Batch laboratory flotation studies conducted on Vale samples showed significantly reduced reagent costs and improved recovery of iron. In this work, the flotation behaviour of the different impurities in the Vale iron ore sample using reverse cationic and reverse anionic flotation processes is compared. Detailed flotation responses are presented and the merits of the two different flotation schemes are discussed.CITATION:Ma, M, Bruckard, W J, Holmes, R and Gontijo, C, 2013. Impurity removal in the reverse flotation of iron ore, in Proceedings Iron Ore 2013 , pp 427-430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By S. Möllerherm, E. Drüppel

"The development of indicators to assess the sustainability of mineral raw materials operations is amajor task with respect to its actuality and difficulty. This holds true even more when dealing withenvironmental indicators.The use of existing environmental indicators in the mineral raw materials industry leads to false orat least distorted results. Therefore the Institute of Mining Engineering I from the RWTH AachenUniversity developed indicators and an assessment system for the mineral raw materials industryon operation, company and sector level on behalf of the Federal Ministry of Economics and Labour(Bundesministerium für Wirtschaft und Arbeit, BMWA) and the Federal Institute for Geosciencesand Natural Resources (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR).In total 30 indicators were defined and designed to assess the performance of the mineral rawmaterials industry in terms of sustainable development, 10 indicators for each pillar (economical,ecological and social pillar).The following paper describes some of the results focussing on the development of environmentalindicators. These had to be adapted or completely new designed in order to match the specificcharacteristics of the mineral raw materials industry."

Jan 1, 2005

By Tapp BA

Australia, considered an energy and mineral resource rich country, is poised on the verge of a major mineral industry 'boom'. It has been repeatedly emphasised that this growth in the mineral industry will form the basis of future economic development. Currently the mining and mineral processing industries use some 32% of the annual primary energy consumption in Australia. This share, although large even now, will increase with the realisation of the 1980's production expansions to 40% by 1985. Two metal industries dominate the energy scenario; iron and steel and aluminium. Major expansions in the local industry will be dominated by the aluminium industry. This highly energy intensive industry has planned major increases in metal production throughout the eighties. The implications of exporting cheap energy to pay for expensive oil imports, the ramifications on Australia's infrastructural ability to supply these major energy needs and the other options that might be

Jan 1, 1981

By Robert Seal, James J. Rytuba, Michael P. Hunerlach, Roger Ashley, Dean Enderlin

Cessation of open pit mining in 1996 at the McLaughlin hot-spring type gold deposit has resulted in the development of two pit lakes that will be managed as permanent lakes with a total storage capacity of 10,000 acre-feet. The south pit lake developed from alkaline ground water infiltration and had an initial pH of 7.2. It contained high concentrations of boron and chloride, indicating that it consisted of a mix of meteoric and evolved connate waters. Numerous carbon dioxide gas vents were present initially in the shallow south pit lake, but as the pit lake increased in depth, gas venting ceased and carbon dioxide is retained in the lower layer of the chemically stratified lake. Continued increase of dissolved carbon dioxide in the lower layer increases the potential for a limnic eruption. A chemocliie occurs at a depth of 47 m. The upper layer of the lake has lower pH, temperature, and conductivity than the lower layer. Effluent from ore and waste rock piles directed into the south pit lake has contributed to high levels of antimony, arsenic, cobalt, copper, mercury, nickel, and zinc. Iron oxyhydroxide is abundant in mine effluent that enters the pit lake and adsorption onto this phase has lowered the arsenic and antimony concentrations. The north pit lake formed primarily from winter surface runoff. The acidic water, pH 4.56, initially had high concentrations of cobalt, mercury, and nickel derived from weathering products of pyritized serpentinite and shales. Buffering by wall rocks has established a slightly alkaline pH of 7.62. The concentrations of trace metals in the north pit lake have substantially decreased due to continued dilution of the lake by surface runoff and remediation of parts of the pit walls that have been covered by backfill.

Jan 1, 2000

Discussion -of the paper of I. N. KNAPP, presented at the New York meeting, February, 1915, and printed in Bulletin No. 96, December, 1914, pp. 2783 to 2793. A. C. LANE, Tufts College, Mass.-Is there any noticeable effect in drilling against salt water? Mr. Knapp says that the mud settles very quickly when brine is added-. What is the effect when you strike a strong salt water ill boring? I. N. KNAPP.-You are supposed to have enough mud pressure in your well to keep the saltwater out. I have drilled against what I knew to be 80 ft. head of water, and hot water too at 99.5°; this water did not show until the well was bailed and the mud pressure reduced. HENRY Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).-Mr. Knapp may be interested to learn that the use of mud in drilling through porous strata is much older than lie appears to be aware of. It has been used notably by Honigmann for boring shafts in Holland and in some of the adjoining portions of Germany. At the Oranien Nassau colliery, shafts about 12 ft. in diameter and 425 ft. deep were sunk in. this way-namely, by boring with a rotary borer, a thick mud puddle being pumped into the shaft, so as to maintain a pressure in the shaft greater than the hydrostatic pressure in the surrounding loose sands and thus keeping the sides of the shaft from collapsing. He will find references to this method in Das Abbohren von Schächten; Handbuch der Ingenieurwissenshaften, p. 134, also in the Transactions of the Institution of Mining Engineers, vol. xiii (1896-97), p. 155. The process appears to have been employed even before 1895, though I cannot give the exact date when it was first used.

Jan 5, 1915

By T. E. Durney

In the Fall of 1987 The Wellmore Coal division of The United Company installed a fines separation circuit in its #20 plant near Big Rock, Va. The addition of the fines circuit included a bank of classifying cyclones and two flotation units; one a conventional 4 cell, 34 m3 Wemco cell, the other an 2.4 meter diameter by 7.6 meter tall, 28.3 m3 column flotation cell. The new fine coal separation circuit is depicted in Figure 1. The column flotation cell is manufactured by the Deister Concentrator Company, Inc., under the trade name Flotaire. The Deister Flotaire column cell utilizes a counter current flow arrangement and a different means of generating air bubbles than that of conventional mechanical flotation cells found in coal processing plants. Other features include diffusers for additional air supply and a froth washer. This cell is one of the few commercial scale column cells processing coal.

Jan 1, 1990

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By E. N. Pennebaker

A PRESENT, a comprehensive account of the geology and ore deposits of the Robinson mining district, in eastern Nevada, is not warranted. Though several years' work has been done, the district is so large that it will be some time before the investigation nears completion. In this paper I purpose merely to discuss methods of study and the application of geologic data to the search for ore. In the first place, the purpose of a geological depart¬ment in a mining organization is to collect and correlate all geologic and engineering data likely to be useful. In an extensive and well developed mining camp this involves a detailed study of the structure and stratigraphy of the district as a whole, as well as careful analysis of the orebodies exposed. The problem then is to find continuations or similar ore environments in other parts of the district in which like phenomena have been active, and to explore these for new orebodies. Experience gained in other similar mining districts is useful but one must always remember that a great many mining districts are unique and that exploration rules and procedure applying to one cannot always be transferred to another of apparently similar character and be made to work. One also has to be careful in moving from one to another part of the same district. The geologist must first examine the region critically to determine its individual characteristics. .

Jan 1, 1932

By K. Baris

Methane (CH4) present in coal seams, generally known as Coalbed Methane (CBM), Coal Mine Methane (CMM) or Coal Seam Gas (CSG), is a major energy source, as it is the primary constituent of natural gas. At the same time, released methane is a potent greenhouse gas (GHG) and a major safety hazard in underground mining operations. Therefore, a considerable effort has been undertaken to develop coal bed methane extraction and utilization technologies that can achieve both environmental and safety benefits. Countries with significant coal reserves and gassy seams, i.e., USA, Australia, Canada, China, India, Poland and Germany have developed mature methodologies and practices to extract, before and during mining, and utilize significant amounts of methane from coal seams. Nevertheless, on a global scale, methane recovery remains untested and many technical and economic challenges require urgent attention. The research presented in this paper, sponsored by the United States Environmental Protection Agency (EPA), is focused on the Zonguldak Basin, the only hard coal region in Turkey. The basin is known to contain very gassy coal seams and consists of three major regions: Armutcuk, Zonguldak and Amasra. Among the three, the Amasra coalfield is considered as the most favorable for CBM recovery, as it comprises of deeper coal seams and where a private company, Hema Enerji A.S. (Hema) is already developing coalbed methane production facilities. This study aims at developing a reservoir model to predict the potential CBM recovery from the CBM-2 well, the only producing CBM well drilled by HEMA Enerji A.S in the Amasra coalfield. History matching was utilized to model the 15-day production data and uncertainty analysis was performed to estimate the optimum values for the reservoir parameters. The produced model yielded an average production rate of 143 m3/day for 10 years. The total amount of CH4 to be produced during this period was 0.53 million m3. Furthermore, the total amount of GHG to be avoided was estimated at 6585 tCO2e.

Aug 1, 2013

By H. O. Hofman

At the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper-Smelting,"' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, FeS. They arrived at this inference from the observed fact that a matte containing Cu,S, 90.4, and FcS, 9.6 per cent. (or, in round figures, Cu2S, 90, and FeS, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent. of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent. of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples gave them a grayish-black field of very uniform appearance, except that five of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the ferrous sulphide-cuprous sulphide series, and to see how the constitution could be further revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, " The Concentration of Gold and Silver in Iron-Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1908

By Doug Smith, Ross MacFarlane

"The Star Lake Mill was commissioned by Cameco (formerly Saskatchewan Mining Development Corporation) in 1986 to process a small high grade gold deposit in a remote location of Northern Saskatchewan. The lean approach to the 200 t. p. d. CIP mill to minimize capital and operating costs employs a number of unique features which are described along with highlights from the initial two years of operation.1.0 INTRODUCTIONThe Star Lake Mine is located 520 kilometers north of the City of Saskatoon (Fig. l) with the nearest population centre in La Ronge 130 km to the south. Gold showings were first discovered in the area in the 1940's with the Star Lake ""21 Zone"" ore body discovered in 1983. The Star Lake Mine started operations in 1986 becoming the first primary gold producer in Saskatchewan in over 40 years. The mine is operated by Cameco (formerly SMOC) with 50\ ownership in a joint venture with starrex Mining Corporation (35\) and Uranerz Exploration and Mining (15%).The limited reserves coupled with the remote location and the price of gold ($300-$350 u.s./oz) at the time the project feasibility was being assessed required a lean approach to make the short term operation successful. This paper describes the approach taken in the design and construction of the Star Lake Mill and describes the mill operation with highlights of the initial two years of operation."

Jan 1, 1989

By J. B. Ackerman, C. S. Bucans

The Sunshine Mining Co. has recently started up its new silver refinery in Kellogg, ID. The new plant recovers silver anc copper values from a high grade tetrahedrite concentrate using hydro- metallurgical processes. The plant and process are both new and have gone through the initial startup phase during the first six months of 1985. The full scale plant was developed from laboratory test work. While the metallurgy of the process worked as expected, the material handling problems were difficult to over-come. As might be expected, those parts of the plant that represented available technology started up easily, while the parts that represented new technology presented the most difficulty. Topics covered in this paper include: 1) insufficient type and amount of agitation in the leach vessels, 2) discharge of a non- homogeneous slurry from the leach vessels, and 3) problems associated with very low flow rates in slurry lines.

Jan 1, 1987

By Paul D. Merica, R. G. Waltenberg

Although nickel was discovered and isolated as early as 1750 and its valuable properties recognized, many years passed before it was used commercially for wire, sheet, rods, etc., in the pure form. This was due partly to its high cost at that time and partly to the fact that it was not possible to refine and cast nickel into ingots sufficiently malleable to be amenable to the usual forging, rolling, or drawing processes. So remarkable was this fact, and so different from the experience at that time with metals such as copper and iron, that it has left its impress on the nomenclature within the nickel industry. To this day, furnace-cast nickel produced in such a manner as to be suitable for rolling and forging is called malleable nickel to distinguish it from the ordinary pig and shot nickel of commerce. In 1878, the firm of Jos. Wharton, of Philadelphia (which later became The American Nickel Works, a constituent of The International Nickel Co.) exhibited at the Paris Exhibition specimens of rolled pure nickel strip and of drawn nickel wire. About this time, there was considerable activity in the study of the refining of nickel and several methods were described, some of which were patented, for the production of furnace-cast malleable nickel including the use of manganese (Boed-dicker,1 Selve and Lotter2), the use of potassium permanganate (Berns-dorfer Metallwarenfabrik3) and the use of phosphorus (Garnier4). By far the most efficient method was discovered by Th. Fleitmann in 1879;5 it consisted in adding to the molten nickel, just before pouring the castings, from 0.05 to 0.125 per cent. of metallic magnesium. This soon became the recognized final malleableizing treatment for furnace-cast nickel.

Jan 1, 1925