Search Documents

By A. R. Troiano, A. B. Greninger

There is need for an adequate working hypothesis that would describe at least qualitatively the crystallographic mechanism for the transformation from austenite to martensite in steel. A general theory would not only be of great assistance in the correlation of existing data and in planning future experimentation, but would also form the basis for an eventual explanation of the property changes that accompany lattice transformations. The mechanism of martensite formation described in the following pages is the outcome of two new experimental determinations: (1) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite, and (2) the measurement and analysis of the change in position that a volume of austenite undergoes when it transforms into a crystal of martensite. For this latter study, the stereographic analysis of shear was employed; this method greatly simplifies the solution of lattice-shear problems, and some space is devoted to its description. Lattiice Relationships and Habits PREVIOUS WORK The lattice relationships between austenite and martensite in carbon steels have been studied by Kurdjurnow-and Sachs,' and by Wassermann;2 and in iron-nickel alloys by Nishiyama.3 Wassermann,2 and Mehl and Derge.4 The studies by Kurdjumow and Sachs and by Wassermann were made on single (austenite) crystals of quenched 1.4 pct carbon steel, and the results of these two independent studies agree closely with the postulated lattice relationships: (III)r||(0ll)a [101]r [111]a [1] Both Nishiyama and Wassermann worked with an alloy of iron plus 30 pct nickel (all austenite at room temperature), and "martensitic alpha" was formed by cooling in liquid air. They agree that the lattice relationships for these conditions are: (lll)r||(011)a [112]r[011]a [2] Mehl and Derge worked with a range of iron-nickel alloy compositions centered about 30 pct nickel. They concluded that when the transformation takes place near room temperature or above, relationship [l] holds, but if the same specimen is made to transform at -195°C, relationship [2] obtains;intermediate temperatures evidently produced a combination of these two relationships. Sachs and co-worker~,1,7 as well as Nishiyama,3 have proposed transformation mechanisms for martensite formation.* Both of the mechanisms picture the transformation as initiated by shearing movements along the octahedral [Ill] plane of austenite, followed by suitable expansion and contraction to complete the transformation. These mechanisms have been described and commented upon by Mehl, Barrett, and Smith,8 Mehl and Derge,4 Wassermann,2 and others, and generally accepted by investigators in this field. Greninger and Troiano9 have recently published the results of a detailed study of the shapes and orientation habits of martensite crystals in plain-carbon and nickel steels. They found that, contrary to previous assumptions, martensite plates form not along the octahedral planes but along austenite planes of very high indices; these results were in line with those of previous studies of martensite reactions in nonferrous alloy systems by Greninger and coworkers.6,10 Greninger and Troiano concluded that the transformation theories of Kurdjumow and Sachsl and of Nishiyama3 are untenable. Phragmén11 reached a similar conclusion. EXPERlMENTAL METHODS The object of this particular study was the evaluation of (1) lattice relationship between austenite and martensite, and (2) relationship between the martensite lattice and the martensite plate. The technique used for solving these problems was similar to that used by Greninger6 on martensitic structures in 8 copper-aluminum alloys. Briefly, the method consists of grinding and polishing a specimen on a surface parallel to an individual martensite plate and thus exposing a single martensite crystal for an area of l to 3 mm. The orientation of this exposed martensite crystal is then determined by means of a back-reflection Laue X ray pattern.12 Another pattern is obtained from the matrix crystal, and a stereo-graphic plot of data from these two patterns then provides the solution to the problem. It is necessary to repeat this process on several crystals in order to determine whether or not the solution is unique.

Jan 1, 1950

By H. R. Gardner

The heat treatmmt of plutonium was studied using the Jominy end-quenching technique commonly used for determining the hardenability of steel. Plutonium specimens were end-guenched from temperatures in each of the ß, y, d, d') and E phases. One series of specimens with a low-iron content, 165 pprn Fe, and another gvoup with a high-iron content, 678 pprn Fe, were used in order to study the effect of a Pu-Pu,Fe eutectic network on the hardness and micro-structure. Hardness traverses indicated no significant variations in hardness with either cooling rate or quench temperature. Metallographic studies indicated major effects on microstructure. Grain size was found to vary markedly with quenching temperature and cooling rate. It was determined that the Pu-PueFe eutectic network could be modified extensively by heat treatment, including spheroi -dization in the y phase and 6 phase below 413°C. An unidentified spheroidal inclusion was observed to go into solution in the delta and higher temperature phases. 1 HE element plutonium is unique among metals in that it has six allotropic forms in the solid state.' These have been designated' as the a, ß, y, d, d', and phases. The respective phase transformations occur at approximate temperatures of 122", 210°, 319°, 450°, and 480°C with a melting point at 640°C. With this number of phase transformations it becomes pertinent to consider the effect of heat treatment and cooling rate in the various phases on the microstructure and hardness of plutonium. To determine; the effect of a wide range of cooling rates, the Jominy end-quenching technique was applied to cylindrical plutonium specimens. In addition, since the presence of iron in amounts greater than 500 pprn is common in plutonium and results in a network of the Pu-Pu6Fe eutectic, it was decided to study heat treatment effects on two bomb reduced plutonium buttons with different iron contents. A low iron button containing 165 ppm Fe and a high iron button containing 678 ppm Fe were selected for this comparison. EXPERIMENTAL PROCEDURE Experimental Material. The cylindrical bars for Jominy quenching were cast from button stock in vacuo in MgO coated graphite molds. Metal pouring temperature was approximately 950°C and the molds were preheated to 300°C. The castings were machined to 0.5 in. diam. by 2.5 in. long cylinders. Chemical analysis and density data for the two groups of Jominy specimens containing different iron contents are presented in Table I. Except for iron, heats 19-12-1 and 20-2-1 are comparable within the limits of analytical accuracy. Representative specimens from the low-iron and high-iron bars were taken for metallographic examination. The low iron specimen was found to have extensive microcracking, Fig. 1. In addition, numerous unidentified spheroidal inclusions were present, Fig. 17. The average grain size of the low-iron plutonium is 0.068 mm, Fig. 4. In the high-iron plutonium, a Pu-Pu6Fe eutectic network is prominent, Fig. 7. The average size of the network is 0.100 mm. Unidentified spheroidal inclusions were also common in the high-iron plutonium. The average grain size of the high-iron plutonium is 0.036 mm. Experimental Technique. A Jominy end-quenching fixture was fabricated for glove box use. A 2.5 in. water height was used with an orifice of 0.250 in. ID. The orifice to specimen distance was maintained at 0.5 in. Annealing temperatures of 160°, 265°, 400°, 465°, and 535°c were chosen for the study of the effect of quenching from ß, y, d, d', and e phases on microstructure and hardness. During quenching, cooling curves were obtained from the Jominy specimens at distances from the quenched end of 1/16, 1/8, 3/8, 3/4, 1-1/4, and 2 in. Cooling rate calculations were made from the cooling curves for temperature intervals of 100° to 110° 160" to 170°, 330" to 340°, 420° to 430°, and 490° to 500°c. These temperature intervals were chosen

Jan 1, 1962

By Rowlands N. J, Zimmermann D. O

The Engel Model search simulator is described with particular emphasis on preparation of input parameters. The computer has a "black box" role in the same way a telephone or radio is a "black box" in communications. A search technique (sensor) is selected and applied in two stages of'search, namely, reconnaissance and detailed. The model relies on knowing and quantifying the parameters of the target sought and the search technique; this is usually done by analogy studies from available literature and experience. The parameters are then balanced by feasibility studies on the search area. Case histories show that the study makes the user aware of what he is likely to find rather than what he wants or needs to find to be viable. Two case histories are presented: one for Mississippi Valley type lead- zinc deposits and another for stratiform copper. The first study showed particular benefits in the input stage and highlighted the fact that one could expect a lot of encouragement by way of interesting results but with little chance of finding the high-grade,

Jan 1, 1974

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By Samuel J. Sims

The Grace mine magnetite deposit, located 2 miles north of Morgantown in Berks County, Pennsylvania, was discovered in 1948 by an aerial magnetometer survey. It is situated on the southern border of the Triassic lowlands section of the Piedmont province. Cambrian sandstones, shales, and limestones overlie Precambrian crystalline rock and were folded and thrust-faulted during the late Paleozoic Appalachian revolution. Late Triassic continental sediments were deposited on the deformed basement rocks and were intruded by Late Triassic diabase dikes and sills before regional tilting and normal faulting occurred. The Grace mine magnetite ore is characteristic of the Cornwall type. The ore has replaced a Cambrian limestone lens isolated between Triassic diabase footwall and Triassic sedimentary rock hanging wall. The ore body is roughly tabular in shape, dips 20° to 30°NE and plunges about 20°N80°E. The ore is granular, fine- to medium-grained, typically consisting of unevenly distributed magnetite in a matrix of light green to white serpentine gangue. Magnetite is the major ore mineral, pyrite and chalcopyrite are common accessory minerals, and pyrrhotite occurs locally. Sphalerite, marcasite, galena, hematite, digenite, and goethite are uncommon. Serpentine, talc, and chlorite are the major gangue minerals; calcite and dolomite are common, and phlogopite, tremolite, and biotite are present locally. Apatite is a common accessory; sphene is rare. Calcium-magnesium silicates were formed first by contact metamorphism of impure limestone by the intruding diabase. Later, the silicates were altered hydrothermally to the serpentine- talc-chlorite assemblage now present. Magnetite, the first ore mineral, formed by replacing serpentine and was followed by pyritepyrrhotite and then by chalcopyrite-galenasphalerite. Marcasite, secondary pyrite, goethite, and hematite are secondary minerals resulting from alteration of pyrrhotite and magnetite. It is estimated that confining pressure was about 1500 bars and the temperature range was 500° to 675°C during ore formation.

Jan 1, 1968

By A. L. Holley

There is a growing demand for pure and cheap material for fine open-hearth steel; a material not only very free from phosphorus, but from carbon and silicon; so that it may he rapidly converted into steel. Iron and steel scrap are not trustworthy as to quality, and they are often dear. There are three methods of purifying cheap materials for the open hearth. 1. Mechanical puddling, as done at Creusot, which removes 90' per cent. of the phosphorus from the pig iron. 2. Krupp's washing process (the conduct and results of which 1 fully described in a former paper*), which eliminates 70 to 80 per cent. of the phosphorus and most of the sulphur and silicon from pig iron. Neither of these processes would sufficiently purify, for very fine steel, those very impure pigs which are cheapest in many parts of the United States. 3. The process of producing directly from the ore an iron which is practically pure chemically, although mechanically mixed with the impurities of the ore. This is the oldest of iron processes ; one form of it, the CataIan forge, employed to produce charcoal blooms, is still in use, but its great cost is rapidly throwing it out of competition. Among the modern attempts to produce iron direct from the one, on a large scale and at a cheap rate, several have been in various respects successful. Dr. Siemens's process of treating a ton and a half or more of ore and the coal to deoxidize it, in a rotating gas furnace, and bringing out, in some four hours, a ball of chemically pure iron so soft that the fluid and impure slag may be sqneezed out of it, is the most attractive and the most highly developed of all the modern direct processes. I hare watched it, from time to time, since 1874, and have noted a steady improvement. It may now be said to have passed the experimental stage, although, like older processes, it must be adapted by practice to special materials. The cause which has been more potent than all others, including the defects of the best direct processes, to bring these processes into disrepute, is the wasteful treatment of the direct product. With one or two exceptions (when failure mas due to other and obvious causes), the direct product has been made into wrought iron (weld iron). Even Dr. Siemens has, at Towcester, in England, and at Park, Bro. & Co.'s, in Pittsburg, set up his apparatus for this purpose. Is it likely that

Jan 1, 1880

By Fred P. Dewey

IN preparing material for the exhibit of the National Museum at the New Orleans Exposition in 1881, it was decided to attempt to photograph the interior of a coal-mine, in order to get a strictly truthful representation of a thick coal-seam, and to show incidentally the methods of mining. While we have many drawings, both mechanical and artistic, illustrating the subject, they are not satisfactory for these purposes, simply because they are drawings. Aside from this, much interest attaches to pictures of inaccessible places, and the enlarged copies (30 inches by 40 inches) of the photographs we succeeded in obtaining, have attracted a large amount of attention from the visitors to the Museum. The Kohinoor colliery, Shenandoah City, Pa., was selected as most suitable for the attempt, principally on account of the fine exposure of the Mammoth bed, and the comparatively level character of the workings, in that colliery. This is one of the many anthracite-mines of the Philadelphia and Reading Coal and Iron Company. A detailed section of the fiftyfoot or Mammoth bed in this colliery is as follows: Feet. Inches. 1 0 Clod. 1 7 0 Coal. 1 0 Slate. Top Split. 8 0 Coal. 1 6 Slate divider.* 6 0 Coal. 1 0 6 Slate. 2 6 Coal. 0 5 Slate. 1 8 Coal. 1 2 Charcoal. 5 0 coal. 1 0 Bone and Coal. „ „ Coal. [ Bottom Split. 0 6 Bone and Slate. 3 0 Coal. 0 10 Bone and coal. 1 2 Coal. 0 2 Bone. 4 4 Coal. 0 1 Bone. 0 8 Coal.

Jan 1, 1888

By D. A. Kraai, S. Floreen

The effect of 1 to 50 ppm S on the ductility of nickel at 800° to 1400°F was studied. Results at each temperature showed a decrease in the reduction of area from approximately 95 to 5 pet over the sulfur range studied. Ductility varied with grain size, but only to a minor extent relative to the sulfiw effect. The effects of sulfur were completely offset by the addition of small amounts of magnesium. The results indicate that the "hot-short" loss in ductility is not an inherent property of nickel. Some possible mechanisms which cause the loss in ductility are described. MANY metals or alloys that normally possess high ductility exhibit a ductility loss at intermediate temperatures. This loss in ductility is often called "hot-shortness". Numerous examples of this phenomenon have been reported in the literature. Much of this work has been reviewed by McLean1 and by Rhines and Wray.2 To date there is no fully satisfactory explanation of the cause of this intermediate-temperature hot-shortness. It is generally recognized that impurities, and particularly impurities that form low-melting phases, can cause embrittlement. Examples of hot-shortness have been reported, however, where there were no obvious impurities present which would lower the ductility. Thus there has been some basis for believing that hot-shortness is an inherent property, and that even the purest metal would display a hot-short loss in ductility. This latter hypothesis was recently put forward by Rhines and wray2 based on studies of nickel and nickel alloys. In the discussion of this paper, however, Guard noted that high-purity nickel showed no hot-shortness.3 Thus there is reason to doubt whether pure nickel, or by inference any other pure metal, will inherently exhibit hot-shortness. The present work was initiated to determine the extent to which hot ductility was sensitive to very small amounts of an impurity element. If it could be demonstrated that hot-shortness could be induced by only minor amounts of an impurity, then it might be argued that hot-shortness in general is an impurity effect, and not a fundamental property of pure metals. The particular impurity studied was sulfur in nickel. The deleterious effects of sulfur are well- known. It is also well-known, and will be shown below, that additions of magnesium will render sulfur innocuous. When no such refining agents are added, however, the Ni-S system is a very useful one for studying the influence of small amounts of impurities. EXPERIMENTAL PROCEDURE Two heats containing -24 ppm S were vacuum-melted and small amounts of magnesium were then added under an argon atmosphere. These alloys were used to show the effectiveness of the normal magnesium treatment in overcoming the influence of sulfur. A second series of alloys with a sulfur range of 1 to 50 ppm was then prepared by vacuum melting nickel in alumina crucibles. No elements, such as magnesium, which tend to combine with sulfur were added. The higher sulfur contents were attained by adding nickel sulfide. Lower sulfur contents were prepared using a method in which the melt was oxidized under vacuum to produce the reaction S + 2O = SO2 These heats were subsequently deoxidized with carbon. Ten- to twenty-pound ingots were cast of all of the alloys studied. The compositions are given in Table I. The ingots were forged and hot-rolled to 3/4-in. bar. They were then annealed at either 2000" or 1600°F to produce different grain sizes. One-quarter-in.-diam tensile specimens were machined from the bars. These were tested at 800°, 1000o, 1200°, and 1400°F. The specimens were held at temperature approximately 45 min before testing. The strain rates were 0.005 min-1 to yielding, and 0.05 min-' after yielding. No extensometers or gage marks were placed on the specimens because the higher sulfur heats tended to fracture at the knife-edge indentations or gage marks. The properties measured were ultimate tensile strength and reduction of area. The analytical technique for determining sulfur at low levels was that developed by Burke and Davis.4 They reported a standard deviation of 1 ppm at an average sulfur level of 4 ppm in NBS standards. A standard deviation of 3 ppm is probably more realistic for the alloys used in this investigation considering the possibility of some segregation in the ingots. RESULTS A summary of the tensile results is given in Table I. As shown in the table, both heats to which

Jan 1, 1964

By Peter J. Clarke

Development of the mineral and energy resources of Afghanistan appeared to be a top priority of the Soviet-controlled Government in the country. In the Afghan Government's plan for 1980-81, the largest allocation in the development budget was for mines, industry, and energy (46.7%). In contrast, only 23.1% of the budget was allocated for agricultural development, despite the fact that the great majority of the population was dependent on farming. The mineral industry of Afghanistan consisted of the production of natural gas, cement, coal, fertilizer materials, and rock salt. Production levels for all of these commodities were down an average of 45% from those of 1978, before the Soviet invasion. Prior to the invasion, small quantities of asbestos, barite, and talc had been produced along with about 6,000 to 7,000 kilograms per year of lapis lazuli, a semiprecious gem stone. Afghanistan had supplied about 80% of the world's output of lapis lazuli. Following direct Soviet intervention, production of these minerals declined to near zero.

Jan 1, 1983

By S. W. Parr

FRom a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows: Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric acid— 1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60" C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present. Sulfur in the form of iron pyrites, or marcasite, may be quantitatively removed without oxidation of the organic sulfur as follows: A dilute solution of nitric: acid is prepared having 1 part of concentrated HNO3 to 3 parts of water or with an approximate specific gravity of 1.12. The coal sample, ground to 100 mesh, is digested with this solution at room temperature for 3 or 4 days, filtered and evaporated to dryness, taken up with water, and acidified with hydrochloric acid. It is now ready for precipitation with barium chloride in the usual manner. If sulfate is present in the original sample to an appreciable amount, it should be removed by the procedure outlined above. It is not necessary here to give the methods for determining the two

Jan 1, 1920

By G. C. Price

This study traces the development of the bucket-wheel excavator, points out the differences in the German- and American-type wheels, and gives the major design criteria and the advantages and disadvantages of bucket-wheel operations. A computer program, written in FORTRAN IV for use with an IBM 360 computer, simulates the operation of the digging components of a bucket-wheel excavator. By supplying certain mining dimensions, soil characteristics, and machine design specifications, this program will print out a time study of the various components of an operation, power calculations for the operation, and production data. This program, when combined with a truck, belt, or rail program, should be helpful in planning a complete mining system In material suitable for a bucket-wheel excavator operation.

Jan 1, 1973

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By R. D. Brown

On November 16, 1978, Finance Minister Chretien delivered his second formal budget in the House of Commons. Over-all, the provisions of the budget should provide moderate stimulus to the Canadian economy. With respect to the mining industry, the budget offers some welcome changes in the form of' improved write-offs for development expenses and social assets; higher investment tax credits; and a reduction in federal sales tax. On the other hand, income bond financing of new mineral ventures may be restricted.

Jan 1, 1979

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By M Monaghan, B S. Gregory

The Geita Gold Mine is located 80 km southwest of the town of Mwanza in the north-west of Tanzania and is 100 per cent owned by AngloGold Ashanti Limited. Open pit mining commenced at Geita in 2000. In 2011, the operation produced 494 000 oz at a cash cost of US$536/oz. This is a significant improvement from 2008, when 264 000 oz were produced at a cash cost of US$742/oz.A period of relatively poor operating performance at Geita was recorded over the period from 2006 to 2009. A period known at Geita as æthe turnaroundÆ commenced in 2009, and has been remarkable to say the least. Over the last couple of years the mine has embarked on a journey, which saw various interventions and initiatives. Among the key initiatives were Project ONE (which focuses on business process framework, systems for people and safety transformation), asset integrity, fatigue management and contract mining of satellite pits.Since the commencement of the turnaround at Geita, gold production has matched market guidance. The mine has returned to positive cash flow on the basis of strong performance on cash management, improved production and increased gold price.This paper explains some of the details of the mine operationsÆ improvements, how they were implemented, their relative contributions to improved mining performance and the path ahead to best practice. Observations will be made about some improvement rules that can be applied generally in open pit mining.CITATION:Gregory, B S and Monaghan, M, 2012. The path to best practice at Geita Gold Mine, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By P. Leeuw, H. Mtegha

"The aim of this paper is to enhance the understanding of the nature of mining input technologies in the South African mining industry. In the context of this research, mining inputs refer to input technology into the activities in mining engineering fields, which include mining-related production activities, rock engineering, mine ventilation, and mine transportation (handling of personnel, material, broken rock, and pumping). Input technologies in supporting fields such as geology, other engineering disciplines, human resource, procurement, finance, as well as downstream fields that include metallurgy, and marketing of minerals, were disregarded.The mining input technologies were divided into 12 nodes, and data from a sample of 150 first-tier mining suppliers was analysed. It was found that, in general, there is a high local content in mining input technologies, particularly as regards technical support services, artefacts, and machine technologies. This points to the presence of mining-induced backward linkages in the South African mining industry. The majority (83%) of companies that provide input technologies into mining are located in Gauteng Province, and relatively few are found in provinces where mining is concentrated such as North-West, Limpopo, Mpumalanga, and Free State. IntroductionSouth Africa is well endowed with minerals, with more than fifty different minerals being mined throughout the country. For this and other reasons, mining is one of the crucial pillars in the South African economy and its importance is well documented (Robinson and von Below, 1990; Creamer, 2010; Department of Mineral Resources, 2015). In 2013, South Africa was the largest global producer of chromium, ferrochrome, platinum group metals (PGMs), and vermiculite and the second largest global producer of antimony, manganese, titanium, and vanadium (Chamber of Mines of South Africa, 2014). In 2013, the mining industry contributed 6.7% to South Africa’s GDP and was the fifth largest sector in the economy, as shown in Figure 1."

Jan 1, 2016

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By Helen Francis

Over the last decade, lower ore grades and deeper mine environments have demanded that mining companies develop new technologies (tools and processes) to ensure a mine?s economic sustainability. At Inco Ltd., this demand has lead to the focus of technological development within the area of automation. Delineation (Drilling and Interpretation) is a key step in the determination of ore grade and location and therefore was chosen as a priority area for enhancement through automation. Focusing on the tools (the diamond drill) automation, significant benefits have been consistently achieved in terms of productivity, process efficiency, operational safety, cost reduction, component life cycles and machine reliability. It is suggested that optimum benefits have yet to be achieved, and will not be achieved until the human aspects of automation have been properly addressed. Since project inception, the human aspects of automation were recognized as critical to the success of the diamond drill automation project. However, it was only upon the installation of the Automated Diamond Drill in the field and its continued use on a daily basis that this issue received due attention. The human aspects of automation can be broadly addressed as economic, physical and psychological. This paper, with examples from the field, will discuss the human aspects of automation in each of these areas. The paper will draw from observations and experiences acquired throughout this project and recommend implementation strategies that should be utilized in future automation projects to enhance both the acceptance of automation and the success of the automated process itself.

May 1, 2002

By ev, Ze&apos Reches

The growth of networks of shear fractures is explored in a series of experiments with samples of wet clay. The samples are subjected to plane strain deformation in a rigid apparatus. The individual fractures observed on the upper surface of the clay samples grow longer by three mechanisms: in-plane propagation, off-plane propagation and coalescence. New, active fractures cut and displace older, less active ones. The lengths of individual fractures display lognormal distribution in most cases and power distribution in fewer. The calculated length parameters in the experiments, as well as in three field cases discussed here, suggest that the fundamental parameters in fracture analysis are the normalized cumulative length and the length of the shortest fracture measured.

Jan 1, 1986

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968