Search Documents

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By A Scott, I Onederra

Most iron ores occur in mine benches as complex mixtures of lithologies and ore types. This significantly complicates their characterisation for both blast design and fragmentation modelling. A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful engineering models are currently available to blasting engineers and consultants, and more sophisticated approaches using mechanistic descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The engineering or empirical models that are in more general use within the industry, such as the Kuz-Ram model, require appropriate data if they are to generate useful fragmentation predictions. Some of these models have reached significant sophistication and have made very useful contributions to both routine blasting operations and the exploration of new blasting paradigms. However, these models struggle to adequately deal with rock that is as complex as iron ore. This paper reviews the characteristics of the most successful blast fragmentation models available to the industry and discusses approaches to the derivation of suitable rock mass properties to adequately describe blast fragmentation in a range of iron ores.CITATION:Scott, A and Onederra, I, 2015. Characterising the blasting properties of iron ore, in Proceedings Iron Ore 2015, pp 481–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R. L. Wooten

When discussing what Coal Mine Safety in the future will be, it is important to examine three areas which at present provide significant parameters to the industry. These three areas are: 1) Safety improvements in mining equipment; 2) Labor-management relations; and, 3) The politics of coal mine safety. EQUIPMENT Over the past several decades significant safety improvements have been made in the types of equipment now in use in most operations. Many of these improvements have evolved through mandates from either the U. S. Bureau of Nines, MESA, MSHA; and in some instances, the states. Cabs and canopies are examples of federal mandates while the use of ATRS initially was a state mandate.

Jan 1, 1985

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By Wilfred Lus

Meaningful and real time environmental monitoring of marine tailings placement is a clear sign of deeper commitment to the people of PNG in regard to impacts of mining on coastal environment and marine life. Today daily mine wastes and tailings are increasingly being delivered to the seabed offshore of project sites in Misima and Lihir islands. Ramu and Simberi mining projects also plan to dispose tailings out at deep sea. As tailings leave the tailings pipe and come out into the seabed, concentrations of the cations and other potential harmful particles in the tailings stream need to be quantifiably monitored each day during the life of the refinery. For continuous monitoring of the tailing?s true chemical characteristics submarine cables connected with ocean floor observation systems consisting of deep-sea underwater video, and cation sensors and electrodes will be laid. Power transport to the tailings site and data transfer from the tailings site will be via opto-electric cables. Various data center instruments will record and manage the collected data. Observation data will be transferred in real time to stake holder?s data centers via a dedicated line from on-land stations, and then distributed to company offices and government establishments. Japan Marine Science and Technology Center, Telikom PNG, and Australian Institute of Marine Sciences will be the key advisers in this project. The main role of the observatories is to monitor and collect background seabed geochemical data prior to start of tailings disposal, during tailings disposal period, and after the life of the refinery.

Jan 1, 2001

By Bradley Stoughton

A LL over our great country I have been privileged to see, during the last six weeks, the manifestation of a new spirit among engineers. Partly under the inspiration of leaders whose influence has been felt not only nationally, but internationally, - partly through the recognition of the service that engineers have been able to render to the nation during the recent crisis, a new self-consciousness has been acquired by the individuals, and now this self-consciousness seeks expression in opportunities for service and participation in public affairs. The engineer . no longer sees himself a mere reservoir of information to be tapped when some one is in need of cold facts, no. more an administrator of mere material things, but a potential administrator of- public affairs, a citizen and a human being, with the responsibilities, as well as the privileges of citizenship.

Jan 1, 1920

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By John Fritz

TROUGH it is not a condition of the Award, the fact is that the John Fritz Medal never has been given to an engineer who had not already received one or more similar awards. This "medal for medalists," on the evening of April 20, was presented to Daniel C. Jackling at a special dinner held at the Union League Club in New York. The citation read "For notable industrial achievement in initiating mass production of copper from low-grade ores through the application of engineering principles." The present award recognizes the same accomplishment-the launching and guiding to the port of marvelous success of the Utah Copper Co., first of the so-called "Porphyries"-as did the award of the William Lawrence Saunders Gold Medal by the A.I.M.E. in 1930, and before that the Award of the Gold Medal of the Mining and Metallurgical Society of America in 1926. Following the custom a biography of the Medalist had been published in a small pamphlet as a supplement to the John Fritz Medal Book. T. A. Rickard was the au¬thor of the sketch of Mr. Jackling, an innovation being the placing of a copy of the booklet at the place of each of the diners. The committee in charge of the dinner consisted of two past-presidents: R. E. Tally, of the A.I.M.E., who was chairman; Bancroft Gherardi, of the A.I.E.E.; and Thaddeus Merriman, director of the A. S. C. E., the John Fritz Medal being a joint award of the four societies. Frederick M. Becket, President of the A.I.M.E., as chairman for the occasion, briefly stated the purpose of the dinner. He stressed his satisfaction that the award was symbolic of the cooperative professional activities of the four great national organizations of engineers. He introduced Francis Lee Stuart, past-president of the A.S.C.E. and now chairman of the John Fritz Medal Board of Award. Mr. Stuart outlined the history and purpose of the Medal established in 1902 in memory of John Fritz, of Bethlehem, Pa., one of the great pioneers of America's iron and steel industry, metallurgist, and president of the A.I.M.E. in 1894. Mr. Stuart called the roll of former John Fritz Medalists, three of whom, Ralph Modjeski, J. Waldo Smith, and Ambrose Swasey, were present to do honor to Mr. Jackling. He then introduced George Otis Smith, whose privilege it was to present the Medalist for 1933. Dr. Smith was the senior of the four A.I.M.E. representatives on the Board that last year selected Mr. Jackling for the honor. His speech follows in full.

Jan 1, 1933

By Joshua Alyson Freitas Ribeiro

Aços com teores eutetóides, tratados termicamente são usualmente utilizados em trilhos metroviários. Para que sejam atingidas as propriedades mecânicas desejadas para as devidas aplicações, o material pode ser submetido a alguns tratamentos térmicos, como, por exemplo, Recozimento Pleno, Normalização e Têmpera. Os tratamentos térmicos são de extrema importância, pois possibilitam uma grande versatilidade na utilização dos aços em geral. Neste estudo, as peças utilizadas são provenientes de um trilho metroviário e foram fornecidas pelo Laboratório de Pesquisa e Tecnologia em Soldagem da Universidade Federal do Ceará. Foram feitas análises metalográficas após diferentes tratamentos térmicos em peças do Aço SAE 1080 Fe-C com o objetivo de verificar os aspectos microestruturais e a sua inflências no comportamento mecânico das amostras e a alteração nas propriedades mecânicas. Pelo fato do material estudado ter uma matriz com composição perlítica de, aproximadamente, 100%, são mostradas as consequências devido à mudança nos espaçamentos interlamelares provocados pela aplicação de diferentes tratamentos e a influência da fase martensita na dureza do material.

Oct 30, 2017

In 1910, he was with the Hidalgo Guadalupe, Pachuca, Mexico, and in 1911 was engineer with the Gualcola Mines Co., at Tuquerres, Colombia. In 1913, he returned to the Sout.hwest, and was employed for that yea.r by the Inspiration Cons. Copper Co. at Miami, and in the middle of the following year he became engineer with the Detroit Copper Co., at Morenci. In the autumn of 1914, Mr. Reece, stirred by his English blood, resolved to return to England to take part in the war. At this time he wrote "I think it will be better for me to resign my membership. If I come through all right, I will apply for re-election." The Institute, however, instead of accepting Mr. Reece's resignation, voted him an indefinite leave of absence, and this precedent soon crystallized into the regular procedure, now in force, of remitting the dues of members in active service. On Dec. 17, 1914, he wrote from Montreal that he fully expected to go over shortly in the second contingent from Canada, with Borden's Armored Brigade, operating with armored motor cars. As he said "this will be active enough service to satisfy any enthusiast, as they are used generally for reconnaissance duty." Soren Ringlund Soren Ringlund died suddenly on July 24, 1918, at Fort Logan, Colo., where he was engaged in service with the Medical Department of the U. S. Army. Mr. Ringlund was born in Denmark in 1875. He came to the United States in 1902, and became a citizen in 1908. He graduated as

Jan 1, 1920