Search Documents

E. Hill, South Norwalk, Conn. (communication to the Secretary*) :—The phenomenon described by Dr. Ledoux, involving an apparently abnormal high temperature in the air-cylinders of compressors, has not been, so far as I know, discussed in technical literature. The common formula for the adiabatic compression of dry air does not account for heat suficient to flash ordinarily decent cylinder-oils, nor do the text-books include in their theoretical statements any quantitative consideration of the effect of leaks in the ideal machines which they contemplate. This lack I have endeavored to supply by preparing, in the form of a circular, for the use of the customers and correspondents of the Norwalk Iron-Works, a brief mathematical

Jan 1, 1904

By Y V. Haarlem, P Coghill, N G. Cutmore, M Millen, I Carter

Due to the low concentration of gold, ore sorting for gold has always required measuring indirect properties, such as density or colour, to allow separation on a rock by rock basis. This only works on an ad hoc, by deposit basis and is likely to be least reliable where it is most required in low grade ores. One candidate technique, Gamma Activation Analysis (GAA) has been demonstrated to directly measure gold extremely accurately in powder samples of around 500gm and is used in the Chrysos PhotonAssay assay system. This method uses a linear accelerator (linac) to generate the X-ray radiation that activates the ore at low levels to emit a characteristic gold gamma ray that is then measured by a radiation detector. CSIRO is adapting this measurement technique to application on a belt at up to 800tph to measure pods of ore. The principal differences between measuring samples and an on-line measurement of pods are the requirement to measure coarse ore (<50mm), to measure a larger volume of ore as uniformly as possible, and to have an open-ended geometry with adequate shielding of the linac radiation source. These issues have all been addressed with measurements of coarse ore reported down to around 1ppm in sub-optimal test conditions. They have been demonstrated for <75mm particles with detectors capable of measuring a large volume geometry continuously. These are projected to allow measurements down to 0.3ppm in more optimum conditions for a 10 second measurement time period where the U/Th content of the ore is less than ~10ppm. Extensive Monte Carlo modelling has demonstrated that adequate shielding can be provided in relatively simple geometries with only 1 right angle transfer in the material handling. Steady progress is being made to reach the technical position required to trial an ore sorting system.

Nov 10, 2020

By Emily Dieckman, Claire Kincaid

"When most people think “miner,” they picture an older white man in a dusty shirt and suspenders. He’s holding a gas lamp and a pickaxe, peering at the walls of a dimly lit cavern. This image, while steeped in heritage, is no longer representative of what mining is: a global, increasingly diverse industry.It’s an industry made up of individuals like Zambian-born Chushi Mwewa, PE, president of Southlands Engineering, LLC in the United States and managing director of Southlands Engineering Limited in Zambia; Navajo tribe member Peter Denetclaw, manager of environmental programs and Navajo relations at Freeport-McMoRan; and Chinese and Jewish Alyssa Hom, a project engineer at McCarthy Building Companies.According to the Austrian Federal Ministry of Science, Research and Economics, 168 out of the world’s 195 recognized countries have some mining or mineral resources activity, and the mining industry directly employs more than 25 million people across the globe.However, according to McKinsey & Company’s 2017 “Women in the Workplace” study, white males hold 67 percent of C-Suite positions and 70 percent of senior vice president positions in the corporate world, and mining is no different. This uniformity among leadership has been tied to lower levels of employee engagement, innovation and business growth. The bottom line is this: Diversity is good for business. The question industry leaders must now ask themselves is not “Will we promote diversity?” but “How will we promote diversity efficiently and permanently?”More than 80 industry professionals, consultants and students gathered to discuss this question and share stories at the “Developing Diversity in Mining” workshop organized by the University of Arizona’s Lowell Institute for Mineral Resources (IMR), held during the 2017 SME Arizona Conference in December 2017.Brad Ross, co-director of the IMR and one of the facilitators of the workshop, said he felt diversity was important to discuss because he has witnessed its benefits throughout his career in the mining industry.“By creating a team of people with different experiences and perspectives, a company is better equipped to see the big picture and to creatively tackle problems,” he said. Speakers from industry and academia,including Mwewa, Denetclaw and Hom discussed the challenges surrounding achieving diversity and inclusion as well as the roles and responsibilities of different stakeholders."

Jan 2, 2018

By Paul Gemmill

Production was first recorded from the Pioche district in 1864, and it has continued to show an inherent ability to take on new life after periods of depression in the metal markets. Production from replacement leadsilver- zinc sulfide ore bodies in limestones of Cambrian age now accounts for several times the gross value of silver production from rich fissures in Lower Cambrian Quartzite. Aggregate production of some 6 million tons represents a gross value over $100-million. Future output is expected mostly to be from limestone replacement deposits of which the most productive are "channels" of ore up to several hundred feet wide and several thousand feet long with thicknesses from a few feet up to 50 feet. Such channels are restricted to the lowermost limestone bed of the district, about 250 feet above the basement quartzite. The "blotter-like" characteristic of this highly productive Jimesto~e bed in absorbing mineralization is believed to be, at least in part, due to lithology, including free carbon in the bed, which has created a unique set of conditions for delicately balanced mineralizing solutions that rejected any tendency to replace siliceous wall rock and were properly constituted for replacement of Limestone. All recognizable orogenic history is considered to be related to the Basin and Range faulting that created the mountain ranges. The faults developed after mid-Tertiary time and after widespread extrusives that are themselves involved in the faulting. Flat faults, formerly believed to be part of regional thrust faulting, are now interpreted as gravity slide faulting that can be shown to be large in magnitude and not simply local landslides. Large slide faults generally have concealed the great magnitude of mountain-bordering faults. Mineralization that accounts for ore is later than the faulting. Most faults are pre-mineral since they influence the shape of ore bodies, and some clearly have been offset by fault fissures containing ore. Post-mineral movement probably has been an important component of some large, initially pre-mineral faults. A single period of mineralization was begun by the introduction of large quantities of ironmanganese carbonate, and, in places, carbonate manganese with minor values in sulfides. Closely following the carbonate invasion, massive sulfides were brought in, usually replacing part of the carbonate body though in some places the massive sulfides replaced limestone that was not previously mineralized. Manganese mineralization is not a "halo" but leaks of manganese to higher formations and to the surface are the most significant exploration guides. The Pioche district is expected to be long lived with technological developments in ore treatment being important to the exploitation of low-grade manganiferous ores, while aggressive exploration is expected to find important quantities of bedded lead-silver-zinc ores of the massive sulfide type.

Jan 1, 1968

By J Ashford, Minniakhmetov

Geostatistical simulations are the best practice for uncertainty quantification in non-linear systems. Simulations are currently undertaken on an ad hoc basis in the mining industry due to high requirements in computing environments and advanced geostatistics. In contrast to the estimation process, multivariate simulations can be performed using different methods, tools, and computational environments, similar to data science. For large companies with multiple commodities it is important to have a standard framework to test, build, and run workflows using different methods, applications and computational environments. This work presents an auditable, modular and scalable framework to create geostatistical simulation workflows where the workflow is abstracted from the implementation. Key aspects: automation – workflows should be able to run automatically given updated data (if hands on modelling is not required); auditability – workflows should document key considerations and parameters; modularisation – workflows should permit swapping out components, for example substituting domaining in Leapfrog software with automated domaining using machine learning scripts; scalability – easy, repeatable, portable deployments on diverse infrastructure (for example, experimenting on a laptop, then moving to an on premise cluster or to the Cloud); reproducibility – parameters should be archived to permit re-running and reproduction of workflows in future years; and sensitivity analysis – any component of a workflow should be able to run with multiple scenarios of parameters and data to enable global uncertainty quantification and sensitivity analysis. The presented framework can be used to create different workflows for geostatistical simulations in multiple assets to quantify uncertainty in the value chain for resource categorisation, reserves uncertainty, value of information and robust mine planning amongst others.

Mar 22, 2022

By Neale R. Neelameggham

"Ferrous and non-ferrous metal industries are used to handling several billion tons a year of ore bodies, fuel and fluxing agents by mineral processing techniques and varieties of extractive metallurgy ""Reduction"" processes. Metal industry know-how can be applied to meet the challenge of Reducing CO2 in the atmosphere. Processes for generating alloys of carbon and hydrogen by Reducing the CO2 and water mixture, [carbonated water or water vapor] called Soda, to easily stored fuels are normally endothermic. The processes are similar to generation of hydrogen alone from water which is also endothermic. But hydrogen is more difficult to store than compounds [or alloys] of carbon and hydrogen. This recycling of CO2 and water are possible by using other forms of energy by innovative carbon capture methods.Thermodynamic Diagrams developed for Soda [CO2 and H2O] - metal reactions provide hints for using low cost unused stored energy in un-recycled metallic waste for thermal conversion. Choices for conditions for the electrochemical approaches [using solar - wind - hydropower] are also discussed.INTRODUCTIONIn 2006, I was reading some of the arguments put forth by learned scientists on the benefits and lack of benefits of bio-fuels. I found that the arguments rose partly from the differing system boundaries that were chosen by one versus the other. Some part of the argument may have been based on political climate or atmosphere rather than the analytical science. This situation is seen when scientists discuss which came first - the chicken or the egg, the fuel or biological matter, the oxide or the element, and so on.Then I thought –[just like many of the learned persons participating in this symposium] that common fuels - regardless of them being simple hydrocarbons or oxygenated hydrocarbons or carbohydrates - can all be made from the respective oxides of carbon and hydrogen by simple chemical reductions efficiently carried out in an economical fashion. This is the systematic approach we take when designing a chemical or metallurgical process facility."

Jan 1, 2008

By Philip D. Wilson

FEAST and famine-or, chronologically, famine and feast-have characterized the aluminum supply program during 1943. Fortunately for the war effort the famine phase is over and aluminum production is now in the happy position of being abundantly able to supply all the requirements of the armed services plus a monthly surplus which is building up a substantial stock pile as a reserve against any contingencies. But the present condition of oversupply cannot be attributed to the super-efficiency of the aluminum production program which was designed to take care of the over-all requirements of the war with little or no margin of safety. The present more than comfortable situation is due primarily to the fact that the armed services generally have not consumed anything approaching the amount of aluminum which their requirement estimates indicated.

Jan 1, 1944

By P. G. Hallof

The exploration staff of Campbell-Chibougamau Mines Limited has used past experience to delineate several areas of geologic interest under Lake. Chibougamau. Du• ring the winter of 1964-65, a reconnaissance induced polarization survey was carried out on the lake. First, several lines were surveyed over the known mu1.erahza-tion at the Henderson mine; the grid was then extended into the areas of interest. Several anomalous zones were located and drilled; one, of these proved to be of economic interest.

Jan 1, 1967

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company&apos;s management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939

By Thomas T., Read

E DUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the first really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at first, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work, as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (&lt;1.3) and a high Cu/S ratio (&gt;1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Charles E. Dunne

One of the most frequently asked quesitons is: "Where is copper (price and usage) going?" I will not attempt to forecast either the future price of copper or the future growth of the copper industry; rather I would like to discuss the current trends experienced in the smelting and refining terms and conditions for sales and/or purchases of copper concentrates. A brief review of contract language and terms, together with a review of the common jargon, I believe, would be helpful. To accomplish this review, I will first list what I consider the four basic parts or sections of a basic ore contract and then illustrate basic terms with calculations.

Jan 1, 1984

By Honglei Zhang, Yue Wang, Guotao Xu, Li Liu

The influence of rich oxygen atmosphere on the properties and structure of castables used in the hot wind pipe of blast furnaces was analyzed. Results show that the cold compressive strength of castables is affected by the change of rich oxygen volume in the wind pipe, the bulk density decreases and apparent porosity of castables increases with the addition of rich oxygen in wind pipe. With the addition of rich oxygen, the velocity of heat transfer increase and result of the steel shell become over hot out of safe limit at the thin lining in hot wind pipe.

Jan 1, 2015

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By D François-Bongarçon

The theory of sampling (TOS), and therefore representative sampling, is based on three fundamental principles: sample correctness, which handles the search for non-bias; segregation, the effects of which must be eliminated or minimised; and variance control to help achieve the desired reproducibility. After briefly reviewing these very few, albeit essential first principles of Gy’s TOS, the state-of-the-art in TOS is examined through the prism of these principles and the prospects for the future are explored, with suggestions for further research where relevant. Regarding segregation, which is currently the focus of much research, new orientations are proposed. For correctness, which takes on a major importance when it comes to sampling devices, some new, important principles that have been put forth by recent research, are described in details.CITATION:François-Bongarçon, D, 2014. State of affairs and current research trends in theory of sampling fundamentals, including segregation and correctness, in Proceedings Sampling 2014 , pp 11–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine&apos;s Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007