Search Documents

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By S. Y. Tshipeng, A. T. Kaniki

"RÉSUMÉ La lixiviation acide d’un minerai oxydé cupro-cobaltifère en milieu non réducteur et en milieu réducteur en utilisant le Fe2+ et le métabisulfite de sodium (SMBS) a été étudiée et les résultats ont été comparés. Les tests de lixiviation ont été effectués à température ambiante, dans une pulpe à 30 % solide, avec une vitesse d’agitation de 600 tr/min, un potentiel redox de 350 mV pour les tests en milieu réducteur, et un pH de 1,8. Les tests de lixiviation avec usage du SMBS comme réducteur ont donné la meilleure cinétique de lixiviation du cuivre. Pour le cobalt, c’est l’usage du Fe2+ qui a donné la meilleure cinétique de lixiviation. L’augmentation de la dose du fer dans la solution au-delà de 5 g/L a influencé négativement les rendements de lixiviation du cuivre et du cobalt. ABSTRACT Acid leaching of a copper-cobaltiferous oxide ore in a non-reducing environment and in a reducing environment using Fe2+ and sodium metabisulfite (SMBS) was studied and the results compa¬red. The leaching tests were performed at room temperature, in a 30% solids pulp, with a shaking speed of 600 rpm, a redox potential of 350 mV for the tests performed in the reducing environment, and a pH of 1.8. The leaching tests using the SMBS as a reducing agent produced the best copper leaching kinetics. As for cobalt, the best leaching kinetics was achieved using Fe2+. An increase in the amount of iron in the solution above 5 g/L negatively influenced copper and cobalt leaching yields. INTRODUCTION La République Démocratique du Congo (RDC) est un pays reconnu dans le monde pour son sous-sol qui regorge d’énormes quantités de cuivre et de cobalt (USGS, 2014; Palisade Research, 2016). La technique qui semble être la plus recommandée pour extraire à la fois le cuivre et le cobalt des minerais oxydés cupro-cobaltifères est la lixivia-tion acide en milieu réducteur. Cette technique est appliquée par la majorité des sociétés minières qui exploitent ces minerais dans l’ex-province du Katanga en RDC, à savoir: Tenke Fungurume Mining, Mutanda Mining, Kamoto Cop¬per Company, Sicomines, Gécamines, Boss Mining, Chemaf, Ruashi Mining et Somika. L’usage d’un agent réducteur est indispensable pour l’obtention d’un bon rendement de lixiviation du cobalt. En effet, plusieurs chercheurs s’accordent sur le fait que le cobalt trivalent de l’hétérogénite (CoO·2Co2O3·6H2O) est insoluble à l’action de l’acide seul; il ne devient soluble qu’après réduction en cobalt bivalent (Mwema, Mpoyo, & Kafumbila, 2002; Mulaba-Bafubiandi, Ndalamo, & Mamba, 2007; Ferron, 2008; Seo, Choi, Kim, & Tran, 2013; Stuurnam, Ndlovu, & Sibanda, 2014)."

Jan 1, 2018

By E. Hulthén

Crushing plants are widely used around the world as a pre-processing step in the mineral and mining industries and as standalone processing plants in the aggregates industry. Despite automation and different advanced model predictive control, a lot of the process is still managed by operators. The operators affect a lot of the performance. The numbers of the improvement they can achieve are at least as big as the advanced control algorithms?, today. Therefore, it is also important to train the operators so they know how to behave in different situations. Models for crushers and other production units have been developed during the years and the latest add is the different units? dynamic behavior being brought in, which gives the crushing plants dynamic time dependant performance. This can be used as a simulator for operators training. By connecting a Human Machine Interface (HMI) to a dynamic simulator with the models incorporated, a training environment for operators can be achieved. In this paper, a dynamic crushing plant simulator implemented in MATLAB/SIMULINK has been connected to an HMI via a PLC. The HMI is placed in a control room at the university and complemented with monitors showing sequences from the process connected to the simulations, thus creating a realistic control room for training. In the created training environment, the operators can be trained under realistic conditions. Simple training scenarios and how they could be simulated are discussed. Apart from the increased level of knowledge and experience among the operators, the time is an important factor. While a real crushing plant is still being built, the operators to be can already be trained, saving a lot of the commissioning time. Keywords: crushing, cone crusher, simulator, control room, operator, training

Sep 1, 2012

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002

By Sergio Neves Monteiro, Fabio Da Costa Garcia Filho, Dian Souza de Oliveira

The properties of the nickel based superalloys, in particular 718 nickel-based alloy, are mainly improved by the hardening mechanism, which is based on precipitation of second phases. This work aimed to compare the evolution of precipitation hardening in a 718 alloy microstructure for two different solubilization conditions: 1050 °C for 2 h and 970 °C for 2 h, followed by a period up to 120 h of aging at 800 °C and correlated to the values of hardness. The microstructure was analyzed by optical microscopy. Vickers hardness test was performed and the grain size was measured. It was verified an increase on the hardeness of this material up to 15 h of aging, after that the value decreased to a level that is maintained until 120 h for both solubilization conditions.

Mar 1, 2018

By James Westfield

I welcome this opportunity to appear before you and to review briefly the various health and safety services of the Bureau of Mines available to the mining industry, other than coal, and also to tell of our plans for extending these services to improve safety and health conditions. The Bureau's health and safety activities are basically services by which we attempt to develop and disseminate information on improved techniques in mine accident prevention and promote mine safety education in the mineral industries. Unfortunately, some mining companies, particularly some of the smaller operations, seem to be unfamiliar with these services, The Bureau of Mines is charged by law with the responsibility for inspecting coal mines; other services to the coal mining industry and are provided only on request, Safety inspections and other services that we offer are provided for noncoal mining industries solely upon request.

Jan 1, 1958

By H. L. Ludtke

Microlaminate composites were fabricated by electron-beam physical vapor deposition. The microlaminates consisted of five layers, each 2 to 4 pm thick, and were composed of either pure metal layers (Cu-Ag), or alternated between metal and intermetallic layers (Nb(Al)- Nb3Al). The microlaminates were heat treated in an Ar atmosphere for 2 to 12 hours, at temperatures of 600°C for the Cu-Ag and 1000°C to 1200°C for the Nb(Al)-NbsAl. Microlaminates were examined after deposition and after heat treatment by scanning electron microscopy and energy dispersive x-ray spectrometry. The effects of heat treatment on the morphological stability of these composites will be described.

Jan 1, 1999

By J. S. Roti

Calcium-based scale precipitation is a common problem in mill reclaim waters. An accumulation of these adherent deposits can result in a rapid reduction in water flow, loss of pump efficiency and eventual interruption in ore production. Heap leach applications can also experience the added problems of plugged sprinkler heads, blinded leach pads and fouled carbon columns when scale control is not maintained. The primary cause of scaling in precious metal recovery is the relative insolubility of calcium carbonate. The presence of the calcium ion and bicarbonate alkalinity is common in almost every water source. If the temperature or pH of the water is allowed to increase, the bicarbonate breaks down to carbonate and combines with calcium by the following reaction: Ca +2 +2HCO3 ? CaCO3 + H2 + CO2

Jan 1, 1986

By AIME AIME

EVER since Henry Bessemer, nearly 100 years ago, developed the steelmaking process that bears his name, occasional variation has been noted in the quality of steel made in the acid converter, owing largely to the difficulty of stopping the ? refining-which takes only ten to twelve minutes -at precisely the right moment. Principally as the result of this, the amount of Bessemer steel made in the United States gradually declined over the years until it is now about 7 per cent of the total.

Jan 1, 1943

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By Paul. E. Pesonen

Since early in 1940 the Bureau of Mines has been concerned with possible means of utilizing manganese-bearing materials from the Missouri Valley manganese deposit. During the period between July 1945 and August 1947, the Bureau of Mines undertook to complete certain phases of the problem by re-evaluating the results of earlier work and supplementing the findings by additional operations and field studies considered necessary to permit drawing of final conclusions. Distinctive discoloration marks the outcrop of the manganese deposit which is exposed on both flanks of the Missouri River Valley and its major tributaries for a peripheral distance of approximately 523 miles in south-central South Dakota. The apparent magnitude of the deposit, judged largely from observation of the outcrop, had led to much speculation as to its actual value in terms of tonnage and grade. Similarly, investigative work aimed at developing a means of winning a usable manganese-rich product from the deposit had reached no conclusion, except that certain methods showed more promise than others for accomplishing the final objective.

Jan 1, 1948

By R. R. Klimpel

The use of froth flotation as a means of separating and upgrading sulfide mineral concentrates is standard industrial practice throughout the world. It is ap-parent from observing the industrial practice of sulfide mineral flotation over the last decade that progress is being made in optimizing the operating aspects of flotation. Examples of this are the availability of improved instrumentation and related computer control devices, the modification of mechanical flotation cell designs, the introduction of column cells, better reagent dosage control, blending of feed ores, increasing attention to coarse and fine particle separations, the successful introduction of new frother chemistries, etc.

Jan 1, 1989

By D. E. Stone

Solid and liquid impurities must be removed almost completely from synthesis gas for the production of synthetic liquid fuels because of their effect on the synthesis catalyst and turbocompressors. The maximum permissible concentration of dust has been set at 0.05 grain per 100 cubic feet.5/ This is one part per million by weight, or about the same concentration as in average city air. The cost of synthesis gas is estimated to constitute 60 to 70 percent of the total cost of the synthetic liquid fuel. For this reason this station is developing processes using coal instead of the more valuable coke as raw material, which promises reduction in cost of the synthesis gas. This, however, increases the difficulty of attaining the above dust value. As failure of the dust-removing equipment to produce high-purity gas may ruin valuable equipment within a few minutes, it is imperative that a reliable and continuous method be obtained for determining such extremely low concentrations .of dust in the purified gas. A suitable device must also instantly sound an alarm and, if necessary, automatically actuate the proper valves to prevent damage. The Ess Instrument Co. designed and built an instrument which they believed might fulfill these specifications. It' continually compared, by means of photoelectric cells, the intensity of a light beam passing through the gas and a similar beam passing through clean air. For maximum sensitivity, the photocells were connected back to back, i.e., anode to cathode and cathode to anode. The difference in voltage produced by the two cells was amplified and operated an indicator.

Jan 1, 1951

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023