Search Documents

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By E. H. Burroughs

HISTORICAL REFERENCES OCCURRENCE-GEOLOGY AND ORIGIN. 4. ARNOLD, RALPH. Conservation of the oil and gas resources of the Americas, Econ. Geol., vol. 11, Apr.-May, 1916, pp. 203-222; June, 1916, pp. 299-326; Proc. 2nd Pan American Sci. Cong., 1915-1916, vol. 3, Conservation of natural resources, pp. 207-237. Shows occurrence of oll, and status and possibilities of oil Industry in each country. Discusses briefly ways in which oll reserves may be conserved. 5. RUTIS, A. A. Petroleum known since remote times. Oil and Gas Jour., vol. 15, Nov. 2, 1916, pp. 33, 37. Gives historical reférences to the use of petroleum from Bible times to its discovery In America. See also Nos. 3, 257, 202, 337, 1843.

Jan 1, 1919

By Dozier Fircley

SOME nonmetallic minerals and their products, such as portland cement, common brick and hollow tile, sand, gravel, crushed rock, vitrified salt-glaze clay pipe, and the like, are a necessity in every community. They are mineral in nature but the establishment of plants for their production is usually a local and elementary problem. Yet it is probable that an economic study of the problem in every locality will show that such nonmetallic mineral commodities are not always obtained in the most economical way, or in the best quality. Other nonmetallic minerals are of such value that they may be shipped for long distances and sold in sufficient quantities to establish prosperous commercial ventures. Among these are phosphates, barium compounds, borates, nitrogen compounds, magnesium compounds, sulfur, asbestos, and potash. Success in marketing such products depends on quality, production cost, transportation, and similar conditions.

Jan 1, 1932

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By H. O. Seigel, J. C. Gingerich, E. O. Köstlin

"To satisfy their continuing need to replenish or expand their ore reserves, mining companies are faced with the dilemma of arriving at a proper balance between the dual avenues of discovery through in-house exploration and of acquisition of properties that are relatively proven or are even in production. The returns from exploration activities may be spectacular, but are unpredictable. The allure of an acquisition lies in its promise of quick and risk-reduced addition to reserves. However, it is historically clear that quantum increments in shareholders’ values have arisen primarily through major exploration discoveries, rather than through major late-stage acquisitions. Late-stage acquisitions can prove highly profitable, sometimes based upon the planned use of superior mining or metallurgical technology, but more often occur as the result of unexpected windfalls. At the other extreme, they can become expensive failures through inadequate due diligence, or unforeseeable factors.Citing numerous case histories and industry statistics, it is concluded that a judicious combination of both exploration activity and the acquisition of prospects is the most advantageous strategy for adding new ore reserves. A skilled exploration staff is essential for success, be it through exploration discoveries or through opportunistic acquisitions, preferably at their early stages. In the future, it is anticipated that there will be fewer opportunities for acquisition because of reduced funding for junior exploration companies, leading to increased competition and higher costs for fewer properties, both in the advanced exploration and mining stages."

Jan 1, 2002

By T. Shibaraki

A new larger, more efficient and economical Mitsubishi furnace line at Naoshima was put into operation in May 1991. Naoshima Smelter had produced previously about 230,000 mtpy anode copper with two smelter lines, i.e., a conventional reverberatory furnace line and Mitsubishi furnace line, which had been shutdown at the same time of the start up of the new smelter. At the beginning of the operation, there were several initial problems at the area of off gas trains and feeding system. By overcoming them now the process has been continuing satisfactory operation at the design rate. The paper describes about the design concepts and the actual operation of the new smelter.

Jan 1, 1993

By Henry H. Ginsberg

The Federal Bureau of Mines made pilot plant investigations of the process requirements necessary to produce heavy fuel oil by the liquid-phase hydrogenation of bituminous coal. The investigation was carried out in three separate series of experiments. The first series studied the effect of temperature and contact time on product distribution at 3,500 p.s.i.g. and 420° to 480° C. in the presence of 0.1 wt.-pct../ stannous sulfide plus 0.05 wt.-pct. iodoform based on gross coal. As a result of increased contact times and temperatures, the conversion-6/ and yield of hydrocarbon gas increased, the viscosity of product oil decreased, and elimination of oxygen, nitrogen, and sulfur from coal increased. The yield of oil did not indicate any definite trend with changes in temperature and contact time. The yield of oil ranged from 76 to 85 pct. for Pittsburgh coal and from 60 to 85 pct. for Rock Springs coal. Asphaltenes in the product oil ranged from 17 to 38 pct. of the total oil for Pittsburgh coal and from 12 to 22 pct. for Rock Springs coal. Fuel oils meeting Bunker C or American Society for Testing Materials (ASTM) Grade 6 specifications were produced with Rock Springs coal at 0.2- to 1.0-hr. contact time and 440° to 480° C. and with Pittsburgh coal at 0.3- to 1.0-hr. contact time and 420° to 460° C. In the second series of experiments tin, nickel, iron, and zinc were evaluated as catalysts for the hydrogenation of Rock Springs coal to heavy fuel oil at 3,500 p.s.i.g. and 460° C. Using the apparent conversion of coal as criterion of catalyst activity, at a contact time of 0.45 hr. tin was the most effective catalyst; nickel and iron were nearly as effective, but the use of zinc resulted in much lower conversion. When the contact time was increased to 0.80 hr., the apparent conversion of coal was essentially the same for each of the catalysts. When the yield of oil boiling below 3550 C. was used as criterion of catalyst activity, at 0.45 hr. the order of activity was tin, iron, nickel, and zinc; at 0.80 hr. tin was far superior and the others were essentially equal. The product oils contained from 8 to 20 pct. asphaltenes.

Jan 1, 1960

By R Neivandt, Kane, M O&apos, D Browne

Newmont Australia is the operator of the Mt Leyshon mine near Charters Towers, Queensland. Mt Leyshon is an open cut gold mine, which processed on average 5.0 Mt of ore and produced up to 250 000 ounces of gold per year. Mining was completed in early-2001, followed by treatment of low-grade ore stockpiles for a further 12 months. Approximately 250 ha of waste rock dumps have been rehabilitated. Rehabilitation of two of the three tailings storage facilities (TSF) has been completed and the third is in progress. A field performance monitoring system that includes an automated meteorological station, large-scale lysimeters (measurement of net percolation), and in situ moisture content sensors (measurement of moisture storage changes in the cover material) were installed to monitoring performance of the cover systems placed on the waste storage facilities. This paper focuses on the installation and calibration of the in situ moisture monitoring system. The moisture monitoring system provides automated detailed in situ volumetric water content data above and within the large-scale lysimeters. A portable unit that provides spatial in situ moisture content measurements at additional locations on the cover system is also utilised. The paper will focus on installation and calibration of the in situ water content monitoring instrument in the waste rock, coarse cover material, and fine textured cover materials of the tailings facility and waste rock dump cover systems.

Jan 1, 2003

By A De, B Palmer, rade, P Stowasser, A Fanning

Mining and tunnelling share many commonalities (eg confined working environments, excavation equipment and processes), but of significance is an overarching commitment to provide safe work conditions and environments. This includes reducing exposure to hazardous airborne contaminants such as dust and fumes, in particular Respirable Crystalline Silica (RCS) and Diesel Particulate Matter (DPM), with methods that are environmentally sustainable. In mining, wet methods are common to suppress airborne contaminants, however these methods are reliant on water availability, can be less effective for respirable dust, can have implications for environmental water contamination and can increase maintenance on mining equipment. In contrast, the use of dust scrubbers that provide filtration of airborne contaminants are well established in the tunnelling industry and frequently used to provide spot extraction (dust control at the source) and act often as a complement to the main ventilation system. This paper sought to learn more about the advancements in tunnelling that could be readily applied to mining to improve health outcomes. The paper includes a review of literature and legislation related to health and sustainability and interviews with three respected, and experienced managers from the global tunnel construction industry. It is from these interviews that the focus of the paper turns to Sydney’s WestConnex underground tunnel network and the success of stage 3A M4-M5 construction link. The findings position dust scrubbers as integral to the overall project success as they enabled a Tunnel Production Line (TPL), where multiple stages of construction could take place simultaneously by controlling high volumes of dust at the source. The findings also suggest efficiencies of using mobile scrubbers, both track mounted and hydraulic stepping systems, to accompany road headers and other equipment throughout the excavation process. The findings have transferable applications to underground mining processes in which workers are exposed to high volumes of dust (eg drill and blast) or situations in which dust control at the source, mobility and flexibility offer value (eg room and pillar mining).

Apr 16, 2024

By Nicholas E. Vanderborgh

Projections show that domestic coal will serve for the majority of energy supplies during the next decades. Thorough chemical cleaning of this coal can be accomplished in long-residence time, slurry-transport systems to produce high-quality fuel product. Concurrently, mineral recovery from coals will supplement existing ores. This paper describes this concept and gives preliminary engineering considerations for mineral recovery during transport operations.

Jan 1, 1982

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By D. Mireku-Gyimah, R. S. Suglo

Ghana contains auriferous belts which cover 51 800 km2 of its small area of 239 400 km2. From 1493 to 1600 35.5% of the world gold production was from the Gold Coast (renamed Ghana in 1957). This dropped to 8.9% from 1701-1800. For the past fifteen years annual production has averaged less than 2% of the world total. By 1985 only four gold mines were operating, compared with 45 in 1934 and 11 in 1945. Since 1987 Ghana has experienced a boom in gold mining activities. By 1991, 83 new companies had acquired prospecting licences. At least five new companies have started large-scale production. About 650 licensed small-scale mining groups are in operation. The economic and technological factors that have contributed to the decline of gold production in Ghana are discussed. A summary is given of the methods used to mine and recover gold. These cover small-scale workings, dredging, open cast operations and underground mining. The advantages and disadvantages of these technologies and the future of gold mining in Ghana are considered.

Jan 4, 1993

By C. F., Christopher

The purpose of any steel-making process is to convert the two raw materials iron and scrap into steel. The chemical analysis of the steel is set within certain limits which involve the physical proper- ties desired by the consumer. In addition to tensile properties a large number of other properties are at the present time desired, such as impact resistance, grain size regulation, specific degrees of hardenability, resistance to creep at high temperatures, resistance to expansion on heat treatment, the ability of the product to undergo extreme amounts of cold deformation without failure, and many other properties which are not directly related to the specified chemical analysis. Variations in many of the properties of plain-carbon steels are due to elements and compounds not included in the ordinary "five element"§ composition. Such variations result primarily from variations in oxidation of the metal in the furnace and from the deoxidation method employed. The steel-making problem therefore resolves itself into two distinct sections: (I) the elimination of certain elements from the charge (the iron and scrap entering the furnace) and the addition of materials to meet the chemical specifications for the heat; (2) the manipulation of the slag and metal and the process of deoxidation to give certain desired properties in the steel entirely apart from the chemical analysis specified. Each of 'these two ends must be attained

Jan 1, 1957

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page information circular entitled "Mineral Wool," which was one of the first publications to present to the public Rome technical aspects of the mineral-wool industry. Since then several articles on the subject have appeared in the technical press as well as in publications of State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large number, and in 1935 it was decided to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for nubile distribution. With the cooperation of the industry, this survey was made, and Information Circular 6984, Mineral Wool, was published in January 1930. The issue was exhausted after a few months, and requests for copies continued to come to the Bureau. As opportunity arose, further field studies were made in American as well as Canadian plants. The present circular contains the essential information in Information Circular 6994 together with date from later field studies.

Jan 1, 1939

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By T Bookless, J Pownell, D Meadows

The ever increasing trend of the gold price has meant that ore deposits that were previously considered too complex, or unattractive by virtue of their low gold grade, are now being investigated more closely. These ore deposits present a greater risk of failure than previously was the case. To ensure that the risk of project failure is reduced and the maximum value is derived from the deposit, its mineralogy, as well as other characteristics, should be well understood such that the optimum process can be designed.Quite often the flow sheet design is assembled using individual process components, from various sources, and without consideration of the complete system. Test work programs require careful planning and an open viewpoint in terms of comminution circuit design particularly with respect to ever increasing power costs across the globe. As an example, high pressure grinding roll (HPGR) technology in many cases offers better mineral liberation than the more traditional comminution devices and it does so at a reduced energy input, and yet HPGR test work is often restricted in its scope due to the perceived novelty of the technology and the resultant lack of generally agreed and accepted test work routes.In this paper the authors outline a typical HPGR test work process route driven by the needs of different ore types and illustrate that to optimise the project value, any test work program should start from the premise that thorough understanding of the ore is vital.CITATION:Bookless, T, Meadows, D and Pownell, J, 2013. Enhancing project value through a designed high pressure grinding roll test work program, in Proceedings World Gold 2013 , pp 291-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Paul C. Merritt

The story now unfolding on the Mesabi Range is more than just another chapter in the continuing history of iron mining. It is an epic of foresight, research and pioneering instinct just now culminating in the rapid growth of a new industry hardly more than ten years old. And that growth has been impressive. In the decade that has passed since Reserve Mining Co. blazed a trail as the first successful large- scale commercial taconite operation, the number of plants now existing or soon to be operating has grown to six. From Reserve's initial capacity of 3 million tons of pellets per year, total production capacity on the Range has surged to 31.5 million tons while capital investment has leaped from $300 million in 1955 to almost $1 billion today. During the past year alone, more than $500 million has been committed to these projects, an amount probably greater than that going into any other single mining area in the world. There is more yet to come.

Jan 10, 1965

By George F. Bassett

"More will be expected from the mine or metallurgical plant electrical system in the late 70's and 80's in terms of energy conservation, reliability and fire prevention. Increased electrical loads 1•equired by larger arc furnaces, higher-horsepower motors for mine hoists and pollution control fans, and greater use of electrical heating will have to be supplied. Computers and sophisticated instruments will be used more extensively and have less tolerance for electrical fluctuations. More extensive control and monitoring systems will be required to increase production and minimize operating and maintenance costs. Changing energy costs will prompt design engineers to investigate in-plant generation, particularly where sites are remote from existing utilities lines or steam from turbines may be used in the process. Some utilities are requiring industries to increase their power factor to above 90% ; others are requiring stricter control of voltage flicker from arc furnaces and harmonics from rectifiers. There is a trend to AC with solid-state cont1•ols instead of DC for large cranes."

Jan 1, 1976