Search Documents

By L. N. Hill

The classifiers on the primary grinding circuit at Cyprus Sierrita have been upgraded from 0.66 m (26 in) diameter hydrocyclones to 0.84 m (33 in) diameter hydrocyclones. This has resulted in a 4.3 % (11 t/h) (12 standard tons/hour) increase in mill throughput while producing a flotation feed which contains 4.8% less +300 micron (48 mesh Tyler screen size) material. This reduction in flotation feed particle size has increased copper (CU) recovery by 0.8 %. Various grinding circuit relationships were evaluated. These relationships include circulating load versus throughput, horizontal versus vertical cyclone configuration, and the effect of cyclone components on performance. We conclude that the improvements achieved are due to a shift in the overflow size distribution created by a cyclone diameter more suited to our operation, and by eliminating the cyclone capacity constraint in the grinding circuit.

Jan 1, 1994

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By F. E. Block

The metallic reduction of vanadium chlorides was investigated by the Federal Bureau of Mines as a possible new route for preparing vanadium metal in an effort to develop a production process that would be adaptable to large-scale plant production and would yield metal of uniformly high quality. Vanadium tetrachloride was usually prepared by chlorinating vanadium pentoxide in the presence of carbon. Although oxygen-?free tetrachloride was difficult to prepare this way, it could be prepared by the direct chlorination of vanadium carbide. Lower valent vanadium trichloride was prepared by the thermal decomposition of vanadium tetrachloride. Vanadium dichloride was also prepared by the thermal disproportionation of vanadium trichloride.

Jan 1, 1961

By R. D. Peterson

Autocad has become the standard graphics package for the mining industry as well as the general engineering profession. This paper discusses the evolution that mine planning has undergone and the trend toward compatibility with Autocad. It discusses the common use of Autocad in mine planning and systems modeling using a program called ICAMPS developed by Ohio Automation. As an example of its usefulness the use of the interactive ventilation network modeling capabilities are discussed specifically and are applied to mine planning at an operating trona mine. The ventilation analysis feature of the ICAMPS software works from Autocad drawing of the as-mined map and the projected mine layout. Using on-screen displays of these maps and the snap-on feature of Autocad, the planner designates nodes in the ventilation network, connects them into branches and selects branch characteristics from a side bar menu. The color coded ventilation network appears with the branch parameters alongside each branch. The software calculates the length of airways, computes the branch resistances where needed, converts the input into the required format and passes this information as input data along to the PENNVEN simulation program written by the Pennsylvania state University. Output is available in graphical as well as report format. The color coded graphs include pressures at the nodes and flow quantities on the branches. Since the networks come from the mine maps, the ventilation schematic displays are to scale and can be plotted separately or superimposed on the mine maps.

Jan 1, 1995

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By Robert W. Row

Advanced physical coal cleaning processes that are now under development may remove significantly greater fractions of pyritic sulfur and ash than do commercial coal cleaning processes at comparable heating value recoveries. These processes may be useful for reducing sulfur dioxide emissions from electric utilities and other emission sources. However, little work has been done to determine their applicability to any major coal market. The northeastern states of the United States are interested in burning more coal, but with further sulfur dioxide emission restrictions. Their nearest coal sources are relatively high sulfur Northern Appalachian coals. The project discussed in this paper, which is scheduled to be completed in June 1985, has the objective of technically and economically evaluating various coal supply scenarios involving five selected advanced physical coal cleaning processes; and comparing the economics of them with alternative fuel supply options open to the northeastern users.

Jan 1, 1985

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By Aichun Zhao, Rui Wang, Yihong Li, Yanping Bao, Yafeng Ji, Jiansheng Liu, Xiao Hu, Qingxue Huang

The slag entrapment under different conditions of 80t blowing argon ladle furnace was investigated by physical simulation. The water was used to simulate liquid steel and liquid paraffin was for slag. The processing of slag entrapment under different blowing structures was analyzed and the critical velocity and critical droplets diameter of describing it was obtained. Based on the experiments, the relationship between the interface flow velocity and the critical blowing rate CBR was deduced. In the real process, it is suggested that the bottom blowing rate is from 40 L/min to 180L/min when the interface tension is 0.12~1.2 N/m during the soft argon blowing.

Jan 1, 2016

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

By D. R. Lentz, S. H. Mcclenaghan, J. A. Walker

"Abstract - The Orvan Brook deposit is one of several (Zn+Pb>>Cu)-rich sulfide deposits hosted by the Spruce Lake Formation (California Lake Group) in the northwestern part of the Bathurst Mining Camp. This parautochthonous deposit is hosted by a narrow band of highly deformed, locally graphitic shale that appears to conformably overlie felsic volcanic rocks of the Spruce Lake Formation, and is in tectonic contact with overlying mafic volcanic and related sedimentary rocks of the Canoe Landing Lake Formation. The Spruce Lake Formation is dominated by felsic volcanic rocks and subordinate fine-grained sedimentary rocks, and mafic volcanic rocks (Canoe Landing Lake member). The felsic volcanic rocks can be divided into aphyric and feldspar-phyric rock types. The feldspar-phyric rocks and a few of the aphyric varieties have a Zr/TiO2 ratio of 0.06, and fall into the California Lake Group field on a Y/TiO2 versus Zr/TiO2 diagram. In contrast, the aphyric felsic volcanic rocks have Zr/TiO2 ˜ 0.09 and are marked by high Zr and Th, which is consistent with highly fractionated felsic magma of Spruce Lake affinity. Major and trace element analyses of host rocks suggest that weak to moderate hydrothermal alteration developed on the south side (stratigraphic footwall) of the deposit, which is consistent with a north-younging succession. The sulfide lens strikes east-west for approximately 2.3 km, extends down-dip for at least 500 m locally, and has an average thickness of between 0.75 and 1 m, but is locally up to 5.5 m thick. The contacts of the massive sulfide lens with its host rocks are invariably sharp. Host rocks show evidence of intense ductile deformation as well as later brittle deformation. Compositional layering and sulfide breccia textures in the sulfide body are interpreted to result from deformation or tectonic enhancement of original primary layering. The deposit contains an estimated resource of 2.69 Mt grading 1.73% Pb, 5.95% Zn, 0.37% Cu, 72 g/t Ag, and 0.9 g/t Au. Similarities in bulk d34S between the Orvan Brook (+8.6‰) and the nearby Cu-rich McMaster deposit (+8.2‰) suggest a common depositional setting."

Jan 1, 2006

By C. Flores

It is well known that manganiferous silver ores containing manganese intimately associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily for recovering copper from oxidized and oxide-sulfide ores. A new alternative process combining segregation roasting followed by flotation to recover silver from refractory manganiferous silver ores, was studied using a 23 factorial experimental design. Laboratory investigations have been conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/ton silver to study the effects of additives salt, coke and copper oxide on silver recovery. Results indicate that 79.3% silver recovery can be attained in the absence of copper oxide and 88.4% when the copper oxide content is 1.5% at '750°C, 2% salt and 1% coke and 30 minutes of roasting time. It was concluded that doping with copper oxide improves silver recovery.

Jan 1, 1994

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By H. Lieberwirth, M. Klichowicz

The comminution at grain size level for the liberation of valuable minerals usually requires the highest size-specific energy. Therefore, the full understanding of the comminution process at this level is essential. Models based on the Discrete Element Method (DEM) could be a helpful tool for this purpose. In those, the mineral microstructure, which has a dominant influence on the fracture behaviour, can be described in great detail. One major concern, however, is the missing representativeness of simulated models. In this study, a method to overcome this limitation is presented. The authors show how a realistic microstructure can be implemented into a particle bed comminution simulation using a two-dimensional Bonded Particle Model (BPM). The improved algorithm based modelling approach is exemplarily compared to an equivalent real experiment. Thereby, the focus is set on the analysis of the interfacial breakage and the capability of the simulation to reproduce the experimental results. The comparison of the results shows that simulations at grain size level allow a more detailed evaluation of the fracturing behaviour. This is of special interest as the aim of comminution in mineral processing is not only the size reduction of coarse particles, but an efficient liberation of the valuable components. Hence, simulations with automatically generated real mineral microstructures will help to further improve the efficiency of ore processing. Keywords: Discrete Element Method, grain modelling, particle bed comminution, realistic synthetic

Jan 1, 2020

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By Robert A. Clifton

It seems probable that more and more minerals will be used in plastics as time goes on. This must occur because the minerals will; aid in processability, enhance the engineering properties, reduce the cost, and above all conserve large amounts of petroleum based chemicals. This paper examines the advantages and disadvantages of using the minerals and the ability of the domestic minerals industry to support this possibly very large undertaking. In the author's opinion, it can. This talk is excerpted from a forthcoming Bureau of Mines Information Circular.

Jan 1, 1985

By Robin Shepherdson

Security concerns have prompted the Department of Homeland Security to investigate the use of recording systems on all vessels holding materials used for blasting; a new regulation is expected in the near future. By measuring the strain developed in the legs of vessels with bolt-on sensors, it is possible to monitor the weight of vessel contents. Several companies make this type of sensor and recent versions give the required accuracy. This paper describes two generations of sensor, the second generation having a simpler method of installation that uses standard power and hand tools. Three types of indicator are available to monitor the material weight. 1) A simple electronic bar-graph indicator with a digital weight display. 2) A touch-screen display showing bar-graphs of multiple silos with digital weight displays plus their associated trend graphs, recent readings and an alarm log. 3) A data acquisition unit which acquires the weight digitally from up to 32 vessels and stores the raw and filtered date and time stamped data in a local computer database. This local computer then transmits the data via an Internet connection to a secure central database which allows the weights of all the storage vessels for a company to be viewed anytime and anywhere via the Internet. Historical trend graphs can be viewed and the data can be uploaded into an Excel file for further processing; for example to determine filling or discharge amounts. In addition, E-mail and SMS (Short Message Service) text alerts can be sent automatically when selected alarm levels are reached. Current research and development includes connection of vessels to the central database by a cellular wireless modem when a local computer or Internet connection is not available, as well as connection of remotely located vessels to a central point via “Wi-Fi bridge" radio data links. Future versions will include digital I/O (Inputs and Outputs) to record, for example, activation of filling and discharge devices as well as opening and closing of doors.

Jan 1, 2015

By Klaus Böde

Within the national and international strategy of the German based construction company HOCHTIEF, the majority of its business units is equipped with the comprehensive software package ARISTOTELES. This software is a powerful business information system for all accounting and controlling related processes in medium-sized and large construction and other related companies. Due to the complexity of the software, time constraints, and limited financial resources an implementation of this software package requires thorough project management. In this paper the relevant elements of project management are outlined based on practical experiences gained during this international IT - implementation project. Special emphasis is directed to the identification and management of potential risks. In this case particular acknowledgement was given to the multinational nature of the project and modernization of the business. This includes thorough reorganization of the company, significant changes of job requirements, and substantial trainings for its employees. At the same time key success factors like knowledge transfer, adoption of Czech legal requirements, commitment of management, networked thinking, and integrated project planning come into play. The costs for implementation had to be carefully evaluated because the software was implemented in a country with a considerably low cost I price level. All these impacts to the business had to be managed within the scope of transformation of business and political environment from socialist to market driven economy.

Jan 1, 2002

By John Dasher

One of our War Plants processed Bolivian concentrates as low as 17% Sn by the Arnhem process (pressure leach with HCL) and sent the waste acid down a ditch to Galveston Bay where the chlorides, mostly iron, hydrolyzed. Oyster men, and Texas, demandedimpoundment until a disposal process could be developed. A recycle process found by lab work was recommended, piloted and a plant built. This involved cementation of As Sb, Cu, Bi and Ag on light moving scrap iron and of Sn & Pb on Al turnings (then not recyclable), evaporation and crystallization of hydrous FeCl2, roasting crystals in a muffle furnace and absorbing HCI for reuse. The residue from leaching the low grade concentrates was floated to remove undissolved sulfides, classified and passed over sand and slimes tables to get a smeltable concentrate, a discardable sand tail and a slimes tail worth treating After desliming at 2 micro meters cassiterite, oxide flotation gave good, lab results; but commercial equipment wasn't adequate then. Chloride volatilization, with or without smelting gave high recoveries of Sn as SnCl2, whose marketing was questionable. I have heard this was finally fluxed and smelted.

Jan 1, 1992

By J A. Braithwaite

Social licence to operate is not a new concept for the mining industry, referring to stakeholder approval or acceptance for the activities and impacts of a project, company or industry. It is intangible, dynamic and non-permanent, hence it needs to be earned and then maintained (Thomson and Boutilier, 2014). It has also been argued that social licence extends beyond building approval or acceptance, into engagement for long-term development (Owen and Kemp, 2012).There are many examples where stakeholder opposition – or withdrawal of social licence – have increased capital and operating costs, extended schedules and impacted reputation. At its extreme, the withdrawal of social licence to operate can also contribute to or be the catalyst for mine closure.The key benefit of obtaining a social licence is a reduction of risk. Stakeholder support and advocacy, as well as the implementation of social performance programs that contribute to social licence, can be beneficial in terms of schedule, costs and other benefits.While decisions to close a mine are generally driven by resource availability or economic conditions, the social, economic and environmental legacy remaining post-closure is of importance to many stakeholders. With a number of significant mines now approaching closure within Australia, we are seeing heightened community concern about the economic and social impact of mine closure and the success of land rehabilitation. So how does the concept of social licence to operate extend into the closure phase of the mining life cycle?CITATION:Braithwaite, J A, 2016. Social licence to close?, in Proceedings Life-of-Mine 2016 Conference, pp 176–179 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016