Search Documents

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By F Flitti, M Haest, O Dominguez, D Mittrup, G Hird

The automated geology interpretation (AGI) tool has been developed in BHP Billiton to automate stratigraphy logging of drill holes, using any available quantitative data sets. At present, AGI is set-up to utilise geochemistry and mineralogy from infrared spectroscopic data to predict stratigraphy. Once the AGI tool is calibrated, results show that the tool is capable of automatically defining stratigraphy across all of the deposit types, encountered by BHP Billiton Iron Ore in the north-west of Western Australia. Accuracy of AGI at predicting stratigraphy is on average better than 75 per cent, with average accuracies exceeding 85 per cent for some deposit types. The AGI tool can deliver fast, accurate, consistent and objective geological interpretations.AGI is currently being implemented in BHP Billiton Iron Ore Exploration to streamline the drill hole logging process and allow geologists to spend less time defining stratigraphy at the drill hole level and more time investigating stratigraphy in 3D. This will deliver improved geology models, with significant downstream benefits in terms of better resource models, more accurate mine plans, higher plant efficiencies and more consistent ore products, driving productivity in BHP Billiton Iron Ore over the next decade.CITATION:Mittrup, D, Flitti, F, Hird, G, Haest, M and Dominguez, O, 2015. Semi-automated geological interpretation using assay and infrared spectroscopic sensing parameters towards improvements in geological modelling, in Proceedings Iron Ore 2015, pp 313–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By A. M. Brown, P. V. Straznicky

Dimpling as a means of flush countersinking rivets is an old process predominantly used in secondary structures. The introduction of GLARE as an aerospace material has renewed interest in dimpling and its possible application in primary structures. The dimpling process is able to prevent the creation of a machined knife-edge in the thin aluminum plies of the GLARE sheets. In addition, dimpling eliminates the need to use reduced height rivets, such as the NAS 1097 rivet style. This investigation expands on an earlier study into dimpling of GLARE by Rans and Straznicky. In order to tailor the dimpling process to GLARE, FEM simulations were developed. After verification, a study was performed to find the best parameters for dimpling GLARE3-2/l. Coupon fatigue tests were carried out and the dimpled joints demonstrated increased fatigue lives over the conventional machine countersunk joints. Future wide panel fatigue tests are planned to confirm the usefulness of dimpling thin GLARE laminates.

Jan 1, 2006

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By H. J. Bickel

This paper is concerned with general concepts and statistical devices used in projecting overall energy requirements. Particular emphasis is given to the use of individual end- use markets as an approach to developing future overall energy requirements, and translating these requirements into fuel consumption.

Jan 1, 1962

By Howard Willey

Mining operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of san Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite ; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This paper describes the so-called "filled top slice" stoping method finally adopted as the standard system. Physical and Geological Conditions The principal orebody of the mine is an oreshoot about 1400 ft ng in a fissure vein striking about east and west and with an average lip of 70" to the north. The footwall of the orebody is fairly cleancu and regular both longitudinally and vertically and generally shows a dell-marked post-mineral slip. The footwall rock varies from a fairly strong limestone to a broken, metamorphosed limestone which requires heavy timbering. In some sections it is an altered, crumbly porphyry, which swells badly and necessitates frequent renewal of drift and raise tirnber. The hanging wall is irregular and frequently an assay wall. The stopina width ranges from a few feet up to more than 90 ft.; it averages about 30 ft. For the most part the hanging-wall rock is a shattered and altered monzonite porphyry, nearly aways requiring heavy timbering. The orebody is greatly fractured by post-mineral movement, which usually followed the footwall and left it as a smooth surface frequently covered with a slippery clay gouge. Two well marked transverse faults

Jan 1, 1931

By D. H. Desy

The Bureau of Mines studied the properties of copper that had been oxide dispersion-strengthened with 2 vol pct of either yttria or alumina. Compounds of copper and aluminum or yttrium, coprecipitated from aqueous solution, were converted to oxides; the copper was reduced, compacted, sintered, and extruded. For the resulting copper-dispersoid composites, room temperature tensile properties after annealing in hydrogen, elevated temperature tensile and stress-rupture properties, and electrical conductivity were determined. Compared with oxygen-free copper, copper-2 vol pct alumina or yttria had improved strength after annealing between 400° and 1,000° C, and improved elevated temperature strength, with little loss in electrical conductivity.

Jan 1, 1969

By Y. J. Yu, C. D. Zhang, Y. S. Zhao, W. G. Liang, Y. D. Geng, J. L. Bi

"In this study, the coefficient of thermal expansion (CTE) and thermal conductivity (TC) of shale in two perpendicular directions, vertical and parallel to the bedding of the rock, are firstly measured by experiment. The experimental results show that the CTE of the shale in the vertical direction is 1.69 times as much as that in the parallel direction, while the TC in the parallel direction is 1.83 times larger than that of the vertical direction. Based on the no initial strain assumptions, numerical simulations for the thermal cracking in shale are carried out with the obtained coefficients. Using finite element method and thermal-mechanical coupling theory, two fracture mechanical parameters, KI and J-integral of the shale are also analyzed for the shale thermal fracturing. The simulation results show that both KI and J-integral reach the maximum when the fracturing angle equals to 0° in the shale, namely parallel to the bedding direciton. It is also found that the two fracture parameters decrease with the fracturing angle increasing. Additionally, the thermal fracturing effect of the shale is evaluated under a given scenario. The study is significant for shale oil or gas recovery by in situ pyrolyzing method.INTRODUCTIONOil shale is regarded as a kind of unconventional resource that can contribute to production of shale oil and hydrocarbon gases (Rahm & Dianne, 2011). As is known that there is a large deposit of oil shale in China, and present technology for exploiting oil shale still concentrates on open-pit mining, obtaining shale oil by retorting shale on the ground (Li, Tang, Xue, Zheng, & Du, 2014; Qian, Yin, 2008). However, this technology has a bad effect on the environment and leads to severe resource waste for utilizing oil shale. Exploiting oil shale by in-situ method for ‘green mining’ is widely necessary in China (Kang, Wang, Cao, Liang, Chang, & Liu, 2013; Waters, Dean, Downie, Kerrihard, Austbo, & McPherson, 2009; Zoback, Kohli, Das, & McClure, 2012). One of effective method to exploit shale oil is heating oil shale in-situ underground. For instance, the in-situ conversion process (ICP technique) from Shell Company etc. used a direct heating method, and convectional heating oil shale underground by injecting superheated steam from Mining Technology Institute, Taiyuan University of Technology and constructing horizontal fracture in vertical wellbore from Chevron Company use indirect heating method (Chaudhary, Ehlig, & Wattenbarger, 2011; Hazra, Lee, Economides, & Moridis, 2013; Zhao et al., 2010). The convectional heating method contains complicated procedures with phase transition in double-media of fracture-matrix of oil shale subjected to multi-physical fields coupling including stress, fluid and temperature (Zhao et al., 2010). The characteristics of thermodynamics, solid mechanics and seepage of oil shale have been investigated separately (Hopkins, Rosen, & Hill,1998; Kang, Zhao, & Yang, 2008; Yang, Zhao, Kang, 2010; Zhao, Yang, Feng, Liang, & Kang, 2008; Zhao, Cao, Zhao, Lin, & Wang, 2008). However, it is quite difficult to solve constrained problem of each physical parameter in multi-physical fields coupling for oil shale pyrolysis."

Jan 1, 2015

By Henry M. Howe

In my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel: the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand us. Iron Molds.—If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag is much greater in the former than in the latter, because in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Jan 1, 1910

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905