Search Documents

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By A Satyanaga, H Rahardjo, K G. Mercer

The soil-water characteristic curve (SWCC) is one of the most essential soil properties in unsaturated soil mechanics. The water flow and storage characteristics of an unsaturated soil are closely related to the amount of water contained in the pores and the negative pore-water pressure in the soil. These are both in turn, related to the particle-size distribution and the plasticity of the soil. The SWCC is obtained by laboratory testing which is difficult to perform, costly and time consuming. There is a significant advantage in establishing typical SWCC envelopes for different soil types from a geotechnical design and analysis viewpoint. This paper presents some of the research work undertaken by UWA and NTU to develop SWCC envelopes for soil types classified in terms of the ASTM D2487 Unified Soil Classification System (USCS). This was done by establishing a large database of soils from across the world, classifying them according to ASTM D2487 and undertaking SWCC testing for each soil. This paper presents the SWCC test results from a selection of three of the most common soil classifications encountered in geotechnical engineering practise.CITATION:Mercer, K G, Rahardjo, H and Satyanaga, A, 2018. The development of soil water characteristic curves for soil types classified according to the USCS, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 263–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Edward Rybinski

Compañía Minera Antamina is a polymetallic mining complex that produces copper and zinc concentrates as primary products and molybdenum and lead/bismuth/silver concentrates as by-products. In 2007, Metso Process Technology and Innovation (PTI) was contracted to increase SAG mill throughput by integrating and optimising blast fragmentation, crushing and grinding for the harder M4/M4A (CuZn) ores. Following the implementation of recommendations provided by Metso PTI, the SAG mill throughput increased from 2750tph to reach an average of 3600tph for the remainder of 2007. Due to continued application of mine to mill integration and optimisation philosophy, by 2010, the concentrator consistently exceeded the target of 4400tph while processing harder CuZn ores.

Jan 1, 2012

By Marcel M. Djivre

The paper will outline the destructive test methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. For the evaluation of the mechanical properties of rope samples used in "ultra-deep" single-lift shafts, additional discard criteria used in Ontario, Quebec and South Africa shall be presented. Most of the methods and test procedures currently used at MTL can also be found in the current CSA G4-00 Standard, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage, published in November 2000. In this latest or sixth edition of CSA Standard G4-00, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The CSA G4-00 Standard is also intended for the manufacturing of new ropes, and includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish. To-date the Ontario Mining Regulations require only that destructive test of new ropes be performed in accordance with CSA Standard G4-00, but does not require conformity to the Standard, and on the other hand the inservice wire ropes are required to be tested in accordance with CSA G4 and thus require conformity. The author recommends that the Ontario Mining Regulations (and regulations of other mining jurisdictions) be improved in order to ensure quality control in the manufacturing of wire ropes destined for mines in Ontario (and Canada). Also, the author recommends the revision of the CSA G4-00 Standard by the technical committee in order to address manufacturer?s concerns with respect to compliance, and harmonize the Standard with Internationally recognized Standards.

Apr 1, 2005

By Enrique Francisco Somolinos Garcia-Morales

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 1, 2018

By D. L. Nussear, W. E. Wallace, N. N. Clark, M. Gautam, G. Hong-Guang

"Results from a study directed towards identifying and measuring the mutagenicity of diesel exhaust particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented in this paper. Particulate matter emissions from a diesel engine, representative of the ones found in underground mines, were sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust was diluted in a multi-tube mini-dilution tunnel and the particulate matter was collected on 70 mm fluorocarbon coated glass fiber filters as well as on 8"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the mutagenicity potential.Protocols developed for using a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offer a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within . The surfactant dispersion technique is discussed in this paper. Methods have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surface and physical properties of the particulate material."

Nov 1, 1995

By Giulio Rodrigues Altoé

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of epoxy matrix composites reinforced with continuous fique fiber, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Aug 16, 2017

By J. J. Knoerzer

The scheduled replacement of Inland's A & B coke batteries in Plant No.3 posed some serious problems in terms of pollution control and strained sources for medium volatile coal for a conventional blend. The state-of-the-art of air pollution control during the charging step in the conventional slot-type coke oven has been less than satisfactory. In addition, the work done at the Illinois Geological Survey showed that by preheating the coal blend prior to charging a greater percentage of Illinois coal could be used to produce a high quality metallurgical coke. To assist The Management in the- decision on A & B replacement, Inland Steel conducted a full-scale test program on coal preheating and pipeline charging utilizing the Coaltek system installed on No. 2 battery of the Semet-Solvay Division of Allied Chemical Corporation. The basic objectives of the test program at Semet-Solvay were as follows: 1. Determine the feasibility of producing high grade metallurgical coke from preheated blends containing more than 60% Illinois No. 6 coal. 2. Confirm the performance characteristics in one of the Inland blast furnaces of the coke produced with 75% Illinois coal in the blend. 3. Verify several claims by Coaltek such as: a) Pipelining the hot coal presents no difficulties while essentially eliminates the air pollution problems associated with the conventional charging system. b) Preheating of the coal blend permits the use of higher percentages of high volatile, marginally coking coals (such as Illinois No. 6) in the blend as compared to wet charging.

Jan 1, 1973

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

THE first session, on alloys, took place on Feb. 20, Mr. Hibbard presiding in Mr. Campbell's absence. The session covered papers on manganese, chrom-ium, and silicon-iron systems. The paper by Mr. Wohr-man was presented by title. This paper showed that manganese produced many of the effects generally at-tributed to carbon and indicated that our ideas on manganese-bearing carbon steels will have to be modi-fied. Mr. Krivobok discussed this paper at length, the gist of the discussion being that Mr. Wohrman had not taken sufficient precautions in carrying out some of his work, particularly as to the effect of silicon content. Mr. O'Neill's paper was also submitted by title and no discussion was presented. Mr. Kinzel showed an accu-rate determination of .the carbon-free chromium-iron loop obtained by means of a specially constructed tele-scopic dilatometer. The loop ends at 12.2 per cent chromium and the A-3 line at 900° is unaffected by chromium content. The A-4 line runs from 1400° to 900° at 12.2 per cent chromium as an oblique hyperbola. Mr. Armstrong noted that the brittleness in high chromium alloys is often attributed to the gamma trans-formation and, according to Mr. Kinzel's diagram, this was impossible, as the alloys contain a great deal more than 12 per cent chromium. Mr. Kinzel pointed out that the presence of carbon in the commercial alloys caused the elongation of the loop and made possible local austenite transformation. Mr. Styri discussed the relations of the coefficients of expansion as shown in Mr. Kinzel's diagram. Mr. Corson presented the iron-silicon diagram as he has worked it out, showing a pre-viously unknown intermetallic compound, Fe3Si, to-gether with characteristic martensitic microstructure varying with the heat treatment. This compound formation is the real cause of brittleness in certain re-gions of the iron silicon system. Dr. Hoyt believed some of the evidence presented by Mr. Corson to be in contradiction to the phase rule. Mr. Corson, however, explained that true equilibrium does not exist under the conditions at hand so that the diagram was accurate in spite of the discrepancies. The meetings of the subcommittee on the physical chemistry of steel making were interspersed through-out the day. Mr. Feild presided and a program of future activities was outlined. This includes plans for a symposium at the next annual meeting and methods for interesting physical chemists, particularly those in the universities, in the steel man's problems. This committee has been newly formed and bids fair to be especially active. The Iron and Steel Committee met at lunch at the Engineers' Club at noon, with Dr. Mathews presiding. After disposing of the food the report of the Nominat-ing Committee was called for, and the following were elected as officers for 1928: R. H. Sweetser, chairman; F. C. Langenberg and W. J. Priestley, vice-chairmen; and T. T. Read, secretary. The report of the commit-tee appointed at the last meeting to consider publica-tion and general policy for the committee was then called for and freely discussed, after which it was unanimously voted to instruct the new chairman to se-cure from the Board of Directors the necessary author-ization for the Committee to recognize as a Division. This action was reported to the Board at its meeting the following night and the authority granted.

Jan 3, 1928

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

This paper describes the sinking and lining of a 14 foot 6 inch finished diameter shaft down to and into the salt of a typical dome of the Gulf States region. The conditions and nature of the strata encountered divide the work into three distinct sections - that in (1) alluvial surface deposits, sunk through by open caisson methods, (2) water bearing rock, directly above the salt, and in (3) salt. ACKNOWLEDGMENT The writer wishes to acknowledge the cooperation of the sinking contractors, The Dravo Contracting Co. of Pittsburgh, Pa., through E. T. Gott, vice-president, in furnishing the data used in this paper.

Jan 1, 1932

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a substantial quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives we have considered original equipment manufacturer (OEM) haul trucks, commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application, and efficiently manage energy consumption.

Jan 1, 2011

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the United States for the detection of fire in the belt entry and the monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data have the potential to provide fire characteristic information such as fire growth — in terms of heat release rate — and exact fire location. Such information is critical in making decisions regarding firefighting strategies, underground personnel evacuation and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide concentration, carbon dioxide concentration and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division’s Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy.IntroductionFires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases.The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke and toxic gases are produced and transported by the ventilation system and which provides an indication of the time available for escape or firefighting (Babrauskas and Peacock, 1992). The HRR is also an important input parameter to mine fire simulation models."

Jan 6, 2017

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004