Search Documents

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Robert Walker

The win theme of this session is Unique Material Handing Systems. The theme was selected because of two major factors. 1. Accomplishments of unique character manage to attract interest regardless of their age. 2. There is much to be learned from pioneering efforts of the past as they are the stepping stones to technological development. Thus, 2-1/2 years after completion, the engineering feat of Oroville Dam still looms large let us take a close look at this project to see what made it unique. To begin with, it established a number of firsts: At 770 feet it was the highest earth fill dam in the world. At $121 million dollars, it was the largest ever United States construction project (Civil). At 80 million cubic yards it had the largest earth volume of any dam in the world. The extensive use of belt conveyors for this application had never before been tried. The use of a high capacity bucket wheel-excavator with shiftable belt conveyors had never before been utilized as a con¬tractor's tool. The principal of the "integral train" was applied most effectively whereby up to 220,000 tons of material-was transported daily some 14 miles. To achieve optimum economics a number of technical breakthroughs were necessary. The suppliers of major commercial components worked hand-in-hand with system engineers to develop new machinery necessary for the highly mobile characteristics of the systems, viz., single pulley drives delivering 2000 horsepower, 1000 horsepower right-angle shaft-mounted reducers, across the line starting of 1000 horsepower squirrel cage motors, 10 miles of steel chord conveyor belts with belt tensions up to 150,000 pounds, aircraft-type disc brakes, hydraulic take-ups, train loading at a rate of 25,000 tons per hour, automatic train indexing for rotary dumping at 10,000 tons per hour, roll-over car dumping without uncoupling cars, shifting 7500 ft. long conveyors up to 300 feet laterally without disassembly. These are some of the superlatives that have made the Oroville Dam project unique. The measure of its success is demonstrated by the results.

Jan 1, 1970

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

By Joe Atalla, Jesse Desrochers, Rodrigo Hayashida, Joseph Mukendi Kabuya

The Mont-Wright mine stands as a prominent open-pit operation in Canada, renowned for its vast iron-ore reserves. However, the efficacy of its blasting operations, crucial for efficient production, has encountered challenges due to the diverse lithological compositions across multiple pits. This study presents a comprehensive approach to optimize blasting practices at Mont-Wright mine, tailored to the specific lithological characteristics of each rock domain. Through systematic analysis and experimentation, blasting guidelines were meticulously developed, aiming to enhance grindability and equipment productivity. The implementation of these guidelines promises significant improvements in operational efficiency and resource utilization, positioning Mont-Wright mine at the forefront of sustainable iron-ore extraction.

Jan 21, 2025

By Raymond M. Stateham

A portable, handheld infrared scanner has been used to detect abnormal surface temperature on dumps of flood-generated trash near Wilkes-Barre, Pa. Three of eight dumps examined had thermal anomalies on the surface, indicating temperature buildup at depth. The anomalies found with the scanner were verified by measurements with a thermocouple probe or a carbon monoxide detector. One week after the investigation was completed, open fire broke out at the site of one of these thermal anomalies; about 6 weeks after the investigation, a thermal anomaly in another dump was verified when a trench was excavated in the dump.

Jan 1, 1973

By AIME AIME

MONDAY evening a reception, supper and bridge in honor of the guests of the Woman's Auxiliary was given by the New York Section in the Engineering Woman's Club. After supper, tables were made up for bridge. Some tried jig-saw puzzles, while others merely visited. On Tuesday morning the annual business meeting was called to order by President Bassett. Mrs. Bassett read a note from Mrs. Hoover regretting her inability to be present, and then gave her welcome and message: It gives me much pleasure to welcome you in this annual meeting, and I hope you will be able to come next year, and those who are not able to come this year I hope will be here next year.

Jan 1, 1933

By M. Ataee-pour, S. E. Jalali

So far, a large number of algorithms have been developed for the optimization of pit limits, most of which follow deterministic rules. In this paper, a new algorithm is introduced, which follows a probabilistic logic using the Markov chain process. The algorithm is implemented on a transition matrix that corresponds to the 2D conventional economic block model of the mining area. The probability of mining a block is proportional to the desirability it may provide. Applying this algorithm, the probability of mining each block is obtained, and finally, the optimum pit limits are defined as the pit, which provides the highest probability of mining. In order to validate the proposed model, a numerical example is given and the results of the algorithm are compared to those of a dynamic programming algorithm. A 2D analysis of the problem is discussed in this paper. Although dealing with 3D problems requires larger size matrices, the optimization method is the same and the algorithm does not need any smoothing.

Jan 1, 2006

By T McConachy

New opportunities for miners are beginning to appear through new discoveries, improved knowledge and access to vast unexplored areas of the deep sea and continental shelf. Recent discoveries of undersea hydrothermal deposits show evidence of high-grade mineralisation, although in many instances the extent of the resource is still unknown. The promise and the difficulties of undersea mining have been evident since attempts were first made to mine manganese nodules in the 1960s. The physical nature of the undersea resource is a key influence on its mining potential; and environmental issues will also become increasingly important. This paper explores these issues and concludes with a description of the immediate to medium term applied research required to develop this industry and the spin off that such research can provide.

Jan 1, 2000

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Clarence Linville

IN an article published in the Iron. Trade Review 1 I gave a convenient arrangement for the installation of wet and dry bulb thermometers for use in making moisture determinations in the air being blown into a blast furnace, and also gave a chart for use in obtaining moisture values from the thermometer readings. The data from which this chart was prepared were obtained from the tables in use by the U. S. Weather Bureau.2 The work of Carrier 3 has shown that these tables are somewhat in error. He has recalculated the values for moisture as referred to, wet and dry bulb thermometer readings, and he has prepared a psychrometric chart from the values thus obtained. This work has priced the subject of psychrometry upon a correct scientific basis. I think it is proper that we should recognize the importance of his work and give him credit for one of the most interesting and valuable researches that have been published in recent years. Blast-furnace men are not ready to use, as he suggests 4 a value expressed in grains of water accompanying a pound of dry air. However convenient this may be for heating and ventilating work and other engineering problems, there are several reasons for preferring the use of a value expressed in grains of water in a. cubic foot of mixed air and water vapor, in connection with combustion phenomena and the effects of moisture on blast-furnace operation. Previous papers presented to the Institute have used such values and we have

Jan 10, 1913

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By G. L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from concentrates derived from low-grade domestic chromites. These domestic chromites contain silicon and aluminum impurities at levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten NaOH under oxidizing conditions to form sodium chromate (Na2Cr04)' The reaction product is leached with methanol to recover the majority of the unreacted NaOH, then with water to extract the Na2Cr04 and the remainder of the NaOH. The Na2Cr04 product is recovered by evaporative crystallization from the aqueous solution. This report presents laboratory results of studies to determine the optimum leaching conditions for the reaction products of several domestic chromite concentrates. Results of solution purification and crystallization studies are also presented. The concentrates are from a variety of sources including the Stillwater Complex in Montana, Red Bluff Bay and the Kenai Peninsula in Alaska, and a Ni-Co laterite from southern Oregon. Sodium chromate crystals were produced that contained less than 0.01 pct NaOH.

Jan 1, 1988

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By M. McWha

Laboratory bias is a universal problem in all branches of analytical science. It results from differences in methods, techniques, equipment, and calibrations between laboratories. Notwithstanding that it is a property that can be measured by the use of standards or by inter-laboratory testing, laboratory bias remains a material issue for the mining industry. There is extensive literature and clear guidelines on measurement from the International Organization for Standardization (ISO) and its worldwide federation of national standards bodies (ISO member bodies) and from the science of metrology. ISO guides cover the manufacture and use of standards. An accessible source of literature covering laboratory quality control comes from the public health sector, particularly pathology. There is little doubt in financial reporting rules about the meaning of materiality. Public reporting guidelines are clear that material matters need to be disclosed for investors. Unfortunately there is currently no clear guidance what to do about biased assay results in mineral industry public reporting guidelines. This paper reviews the requirements for the manufacture and use of reference materials, public reporting requirements in the mining industry, and presents proposals to improve management and reporting of laboratory biases. Keywords laboratory bias, reference materials, ISO Guides, financial reporting, materiality.

Jan 1, 2014

By Clarence P. Linville

In an article published in the Iron Trade Review,' I gave a convenient arrangement for the installation of wet and dry bulb thermometers for use in making moisture determinations in the air being blown into a blast furnace, and also gave a chart for use in obtaining moisture values from the thermometer readings. The data from which this chart was prepared were obtained from the tables in use by the U. S. Weather Bureau.2 The work of Carrier3 has shown that these tables are somewhat in error. He has recalculated the values for moisture as referred to wet and dry bulb thermometer readings, and he has prepared a psychrometric chart from the values thus obtained. This work has placed the subject of psychrometry upon a correct scientific basis. I think it is proper that we should recognize the importance of his work and give him credit for one of the most interesting and valuable researches that have been published in recent years. Blast-furnace men are not ready to use, as he suggests14 a value expressed in grains of water accompanying a pound of dry air. However convenient this may be for heating and ventilating work and other engineering problems, there are several reasons for preferring the use of a value expressed in grains of water in a cubic foot of mixed air and water vapor, in connection with combustion phenomena and the effects of moisture on blast-furnace operation. Previous papers presented to the Institute have used such values and we have

Jan 1, 1914

By C. C. Merrill

The Bureau of Mines beneficiated the wastes generated by commercial titanium chlorination operations to reclaim metal values and reduce the problem of disposing of solid wastes. A water leach solubilized about 40 percent of the dry weight and over 75 percent of the metallic impurities. The residue from the water leach was rich in titanium dioxide and carbon; it was combined with rutile and recycled to a laboratory chlorinator. The contained carbon was used in lieu of part of the coke requirement.

Jan 1, 1969

By S. Castro

The aim of the present paper is to review the current technologies for arsenic removal in the copper metallurgical industry, and to show the progress made with some promising emerging strategies, involving the pre-treatment of copper-arsenic concentrates by selective flotation or by alkaline leaching with Na2S-NaOH solutions. The advantages of alkaline leaching are the selective dissolution of arsenic and antimony, the high extraction yield, and the practically nil loss of copper, which remains in the clean copper concentrate as a CuS residue. Alkaline ?cured? ? a procedure similar to ?acid-cured? in conventional leaching ? improves arsenic extraction and reagent consumption, making this an interesting technology for the treatment of high As-Sb concentrates. In light of recent advances on the selective flotation of enargite and tennantite, the importance of redox conditions to control the flotation/depression of enargite-tennantite from copper sulfides has been well established. However, problems of selectivity must still be solved. Additionally, the limitation imposed in some cases by the need to recover the molybdenum by-product must be considered. The application of selective flotation to obtain a high-arsenic or ?dirty? concentrate and its sub-sequent treatment by the alkaline leaching process is suggested.

Jan 1, 2014

By B. Csoke

In a first stage of our investigations material properties of fly ash (three acidic and one alkaline type originating from combustion of various age coal) obtained from four various dumps have been characterized. In a next step systematic mechanical activation experiments??grinding??and measurements have been performed with various ashes to establish relations between grinding fineness (specific surface area), specific work input demand of grinding and activity. In a third phase utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of interrelationship(s) between the degree of activation of fly ash, the lime concentration and the resultant strength of the obtained concrete. Finally, pilot size experiments were conducted and a test road section was built to explore possibilities for the production of suitable binding composition from the mixture of fly ash and lime as well as the applicability such mixture for road construction. After summarizing major achievements of the first and second stages of the work (history) the present study deals with the research conducted in stages three and four. Experimental results support the conclusion that the obtained binding material is suitable for construction of road bedding.

Jan 1, 2014

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011