Search Documents

By T. V. Durkin

Approximately 1,390 t (44.7 million ounces) of gold have been produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection by promoting mining as an industry while requiring prevention of pollution and reclamation of affected lands to a beneficial use. The mining laws have evolved since their inception in 1971, especially in response to gold mining. The laws have remained flexible to meet changing regulatory needs. Gold production has continued relatively unabated, even in the face of public scrutiny, two mining moratoriums, and isolated environmental problems. The department's system of "one-stop-shopping" for environmental permits streamlines the permit process, fosters quick resolutions to compliance problems, and helps keep enforcement actions out of the courts. Specific case histories at heap leach mines within the Black Hills are presented.

Jan 1, 1998

By D. R. Gehring

Effective project management is an excellent technique for meeting a goal through set, well-defined objectives. Even though project management is successfully used throughout the world in various construction projects, underground mining has unique characteristics that require approaches that vary from classical project management theory. Typically, a project includes four main stages: definition, planning, implementation and control. Definition and planning are often the most overlooked stages, but are arguably the most important. This paper addresses practical techniques for the definition and planning of projects for underground construction.

Jan 1, 1996

By George Gazetas, Sissy Nikolaou, Fani Gelagoti, Irene Georgiou, Rallis Kourkoulis

"The need to shift geotechnical design from a “factor of safety” to a “performance based” design (PBD) approach has increased rapidly in the past years following examples from structural engineering. PBD supports sustainable engineered systems that target project-specific geotechnical behavior objectives and results in more rational and, in most cases, less conservative solutions. Resiliency, efficiency, risk optimization, and cost-effectiveness are key components of this approach. For design of retaining walls, the concept of mechanically stabilized earth (MSE) systems combines these attributes, while being environmentally friendly and adaptive to variable construction conditions. Natural hazards, such as earthquakes, may drive the design of MSE systems whose reliability depends on their performance under extreme events. In this paper, the authors compare the seismic response of an MSE steel-reinforced vs. concrete-reinforced retaining wall. The MSE system is composed of a grid of longitudinal and transverse ribs which internally enhances the capacity of the soil backfill. Results of fully non-linear twodimensional (2-D) numerical finite element analyses using two commercial programs with emphasis on the interface conditions are presented. The pull-out resistance of the grid used in the numerical simulation was evaluated from actual pull-out experiments. The results demonstrate a superior performance of the MSE system as compared to the concrete one, especially when subjected to strong seismic excitations.INTRODUCTIONThe idea of performance-based geotechnical engineering is not new, and has been evolving as our perception for ‘good’ performance has also evolved (Kramer, 2008). In early practice, the only criterion for achieving good performance was to avoid failure; designers had only to ensure that the available capacity of the geotechnical system is sufficiently higher than the expected demand (i.e. Load and Resistance Factor Methodologies). Yet, even when the key design requirements against collapse are satisfied, the system may still be placed into a condition in which the deformation constraints are not met (Bolton, 2012). To address these issues, geotechnical design has been developing into a predominantly performance-based approach that correlates deformation considerations to the severity of the experienced loading. As such, in earthquake-related problems, the definition of good performance of a geotechnical system is no more unique; for a low intensity earthquake the system should remain serviceable (i.e., the developed deformations should remain low), whilst for the design earthquake the maintenance of lifesafety is the single performance criterion."

Jan 1, 2016

In a future world of 8.5 billion people in 2035, the Energy Information Administration's (EIA) projected 50% increase in energy consumption will require true "all of the above" energy resource use from oil, gas, renewables, nuclear, and coal. In particular, coal will continue to be the world's energy cornerstone, providing more incremental energy over that same time period than any other single fuel. Coal has long been a centerpiece of a low-cost, high-reliability electricity grid. Today there are 1.3 billion people across the globe without access to electricity and 2.7 billion people who do not have clean cooking facilities. The problem is spread across the developing world, but it is particularly severe in sub-Saharan Africa and developing Asia, which together account for 95% of people in energy poverty. Without a commitment to achieve universal energy access it has been estimated that by 2030, there will be an additional 1.5 million premature deaths per year caused by household pollution from burning wood and dung and through a lack of access to clean water, basic sanitation and healthcare. Modern energy sources are essential to meeting these challenges.

Jan 1, 2012

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By G. Wilson

"Satisfactory hydraulic performance of a centrifugal slurry pump is not the only design criterion. If abrasive wear exists the severity of any damage can be reduced and the life of the wearing parts prolonged by selecting the correct pump to suit the conditions of service. This paper is concerned with the design and construction of centrifugal pumps for handling abrasive solids. The wear phenomena due to the slurry being pumped and the materials used to combat abrasive, wear are outlined. The hydraulic design of the impeller and casing and their relationship to wear and the hydraulic radial and axial unbalance are discussed. The prediction of abrasive wear in pumps can not be precise, as many factors are involved - and this is the object of current research."

Jan 1, 1973

By G. W. Josephson

JUDGING by the progressive atmosphere prevailing in the nonmetallic mineral industries during the past year, postwar conditions were healthful though inflationary. Demand for most industrial mineral products has been exceptionally high and many new production records were attained. Severe shortages of some commodities existed, especially building materials and fertilizers. Production costs and prices increased and profitable operation was general. Under these conditions expansion programs were the order of the day. Ample funds were available to finance the purchase of good equipment; and, as wages and other operating costs were increasing, primary emphasis was placed on attaining maximum efficiency in new installations. These efforts were hampered by shortages and slow delivery of desirable equipment, so compromises in design were often necessary. However, on the whole, production practice improved.

Jan 1, 1948

By R. S. Dean

Boron compounds have been considered for many years as possible additions to iron and steel. A very recent use of boron-steel rods was for the control of neutron intensity in the graphite-uranium pile at the Clinton plutonium plant(130).4/ Norris(129) reports that slags containing boric oxide reduce the ferrous oxide content of steels and thereby the aluminum required for deoxidation. Boron is not considered an alloying element, but minute amounts produce what is often called a "needled" steel. The study of a series of iron-boron alloys by convenient steps, starting with iron containing no boron, indicated that boron was a hardening agent and made the iron very difficult if not impossible to forge. Then came the discovery that very minute traces of boron are quite different from the smallest amount previously thought worthy of study.

Jan 1, 1946

By S. H. Lorain

This paper, which describes lode gold mining in Idaho county, Idaho, is one of a series on western mining districts being published by the Bureau of Mines. It describes mining and milling practices, gives costs, and discusses transportation, climate, power, labor, and other conditions that affect them. The materiel upon which the paper was based was gathered during a field survey in the summer of 1937.

Jan 1, 1938

By Lucius W. Mayer

WHILE the mind of the financier does not normally run along channels similar to those of his technical adviser, engineers, because of their exactness, are ever more called upon to manage affairs where financial matters are involved. It is, true, not a relatively large number have thus far functioned in this capacity. It is also true that the essentially financial mind could not serve in a responsible engineering position; for to be a successful engineer one requires precise thinking, making due allowance for factors of safety. To be a financier seems to require less aptitude for exact thinking than of enthusiasm and confidence in capitalizing prospective possibilities. Both require imagination, the engineer being, more conscious of the limitations of natural conditions. It is to be regretted that the engineer' stands so far aloof from financial matters. Many consider them- selves successful, as did Steinmetz, as long as their reward is the consciousness that they are giving supreme service to mankind. They are 'generally happy in their work and, like our honored brothers who are teachers, gain their greatest satisfaction, not in the amount of their remuneration so much as in the service rendered society and in the excellence of results achieved. Indeed, these sentiments bespeak character and command respect.

Jan 1, 1924

By J. P. Powell

The importance of recovering more oil from known petroleum reserves has placed increasing emphasis on the application of secondary producing methods. One of the most successful of these has been the injection of water into depleted oil reservoirs. Water flooding is now recognized as a valuable conservation measure that not only prevents the premature abandonment of stripper leases but also is credited with reviving operations in many oil-producing areas previously abandoned. The injection of water into an oil-producing zone as a method of stimulating oil production was legalized in Kansas in 1935. Although water flooding had been attempted previously in other parts of the State, 1935 marked its introduction into the shallow stripper area of eastern Kansas. Two years later flooding was begun in the five-county area that is described in this report. Figure 1 is a map showing the water-flood areas in Allen, Bourbon, Crawford, Labette, and Neosho Counties, Kans. To July 1, 1955, the 77 projects in the oil fields of these 5 counties are credited with recovering an estimated 12.3 million barrels of oil that would not have been produced by methods used previously. These projects are expected ultimately to cover 10,700 acres, of which only 5,400 has been flooded to date.

Jan 1, 1957

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By Robert L. Lagace

The objective of this task was to perform theoretical analyses related to identifying and increasing the understanding of wireless propagation mechanisms in mines, and for predicting the performance ranges and limitations of proposed systems. This was to be achieved by building on and extending previous ADL work* and utilizing experimental data as they became available in the radio frequency bands of interest. B. TASKS Theoretical radio wave propagation investigations undertaken on this task centered on three areas. The first area dealt with extending previous UHF wireless propagation results*: to estimate the losses caused by the presence of haulage vehicles such as trains in coal mine tunnels; to estimate the propagation losses and wireless communication ranges expected along a longwall coal face tunnel; and to assess the applicability of previous analytical approximations to tunnels having reduced crossectional dimensions, such as those found in low coal and in the presence of haulage vehicles. The second area dealt with the development of a suitable propagation model to adequately explain the unexpected, highly favorable LF to MF band wireless radio wave propagation behavior experimentally observed in Consolidation Coal Co.'s Ireland mine. The third area dealt with the formulation of a model for evaluating the overall system transfer function and transmitter requirements for a hoist shaft LF communications system, taking into account the hoist rope/shaft transmission line characteristics, the cage and sheave wheel line terminations, the signal inductive couplers, and hoist shaft signal and noise data.

Jan 1, 1975

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

By H. M. Park

Risk is a major factor in all mining activities, arising from many internal and external variables. The authors? research has resulted in a systematic method for the quantification of risk in mining projects (Park, 2012). This is the second part of a three-part series. The first part was published in the October 2013 issue of Minining Engineering magazine and can be found here at www.me.smenet.org. This paper discusses methods of assessing the overall risk associated with those variables, and presents a statistical model based on a survey of 31 experts. The third paper, to be publised at www.me.smenet.org on Oct. 14, presents an evaluation of the statistical model, using data from previous mining investment decisions in which the authors have been involved.

Oct 1, 2013

F. E. Bachman, Port Henry, N. T. (communication to the Secretary*):—In discussing Mr. o.o.Laudig's paper, the Action of Blast-Furnace Gases Upon Various Iron-Ores,' I took the ground that Mesabi-ore explosions were entirely mechanical; but more observation and later experience has caused me to

Jan 1, 1905

By Robert T. Davis

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to the coal-mining industry's underground and open-pit mines that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1964

By T. Adamcewicz

The province's lignite resources lie mainly in the south, extensions of the much larger deposits in Montana and North Dakota. Because of planned additional capacity, conventional steam power generation will probably remain as the dominant resource usage for many decades. Conversion of coal to other energy forms is receiving emphasis and in the future will compete with steam power generation in terms of quantities used.Economic deposits, minable by present-day technology, have been generally defined. Because a large percentage of the total lignite resource is in seams containing multiple partings, future extraction will become much more difficult and capital intensive.Increased public involvement will ensure that the impacts of future coal mining and usage operations are compatible with environmental and social objectives.

Jan 1, 1982

By Tanai Marin

Modelling of pyrometallurgical processes can become extremely challenging when the process involves complex chemical reactions, phase change, multiphase flows, heat and mass transfer and fluid flow. Traditionally modelling involving complex thermodynamic equilibrium and thermochemistry are treated separately from problems in which transport phenomena are dominant, such as CFD and heat transfer studies. The separation is also necessary due to the lack of modelling tools that can effectively couple both solution thermodynamic and transport phenomena or even multiphysics problems. However, there are, quite often, problems in high temperature process metallurgy in which it is not possible to simplify this two modelling approaches. Typical cases of this are for example, the modelling of slag freezing on furnace walls (electric or flash furnaces) to create a protective layer in front of the refractories hot wall, the formation of build up from the matte or metal phases at the hearth of the furnace, calcine smelting from charging piles into slag phase, etc. The problem is even more challenging in nonferrous pyrometallurgy as most, if not all, of the condense phases are highly non ideal solutions involving several components and exhibiting complex crystallization paths and miscibility gaps, such as the Fe-Ni-Cu-S matte, FeO-Fe2O3-SiO2, FeO-MgO-SiO2 slags, etc. In this paper, an approach to model coupled problems involving multiphysics and solution thermodynamic is presented. The approach consists in developing in-house a library containing the Gibbs energy minimization routines and using the local equilibrium concept for process modelling from a multiphysics commercial software (COMSOL). Simple test cases, such as building a non-ideal binary phase diagram on a CFD package is presented, the limitations and of other classic approaches such as equilibrium or Scheil cooling are discussed and compared to this model.

Jan 1, 2015