Search Documents

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By R. H. Lee

WITHOUT doubt, one of the most frequent and serious annoyances connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is ? tight," all available men are put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens-up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a.' cold," or at best a " high-sulphur," east is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot; the pressure rises; the amount of gas made' is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature " mentioned by Mr. .Johnson, and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke, high in sulphur, is used:

Jul 1, 1906

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

"INTRODUCTION Twin Metals Minnesota (TMM) (operating as a joint venture between Duluth Metals and Antofagasta PLC) assumed control of the property in 2010. Amec became involved with the project in 2011 and in 2012 incorporated additional drilling in order to update historic resource estimates. The Maturi geological model and resource estimate was updated in 2014 to incorporate additional information obtained during 2013 and 2014 drill campaigns. In 2017, Amec was purchased by the Wood Group and is now known as Wood. Geology The Twin Metals Minnesota (TMM) Maturi, Maturi Southwest, Birch Lake, and Spruce Road properties are located in northeastern Minnesota (Figure 1). This talk discussed the Maturi deposit only, although all four deposits share similarities. The following geology is summarized from Peterson and Severson (2002).Maturi lies within the Superior Province of the Canadian Shield which is exposed in central and northeastern Minnesota and extends northward into Ontario. In eastern Minnesota, the Midcontinent Rift System developed during crustal scale extension in the Mesoproterozoic Era. The rift system is traceable, as exposures of mantle-derived tholeiitic to subalkaline mafic lava flows, intrusives, and rift-filling fluvial sedimentary rocks, and in the subsurface as a gravity anomaly (high), from the eastern end of Lake Superior, arcing west across the lake basin, and extending south-southwest to northeastern Kansas. Intrusion of the Duluth Complex, circa 1,108 - 1,099 Ma, was related to rifting and is co-genetic with the North Shore Volcanic Group mafic volcanic rocks that form the hanging wall of the Duluth Complex to the east. Cu-Ni-precious metals (PM) mineralization including Pt, Pd, Au and Ag within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex. The Duluth Complex is defined as a more or less continuous mass of mafic to felsic plutonic rocks that extends northeastward for more than 170 miles (275 km) in an arcuate fashion from Duluth nearly to Grand Portage in Minnesota. It is bounded by a footwall of Paleoproterozoic sedimentary rocks and Archean granite-greenstone terranes (Peterson and Severson, 2002), and a hanging wall largely of comagmatic anorthosite, rift related flood basalts, and hypabyssal intrusions of the Beaver Bay Complex. Mineralization is hosted in the basal mineralized zone (BMZ) of the South Kawishiwi Intrusion (SKI). The SKI magmas intruded sub-horizontally between hangingwall Anorthositic Series (AN) rocks and footwall granitic rocks of the Neoarchean Giants Range batholith (GRB). The Maturi local geology and the deposit footprint (shaded orange) is shown in Figure 2."

Jan 1, 2018

By Morsky P, Kalapudas R, Natunen H, Virtanen M

The development of autogenous grinding modification in Outokumpu, known with the name 'Outogenius Comminution', was 'reversed'. At first the metallurgists studied and tested tens of years autogenous grinding in detail in full scale circuits at the concentrators of the company. After the final solution already had been found, also a pilot plant was built and now finally, research work is under way to develop a special laboratory method for testing the suitability of ores for 'Outogenius Comminution'.

Jan 1, 1993

Jan 1, 1957

By Helmer Kraemer

One of the CIM 2003 conference themes is ?Globalization and the impact on mine operations?. In this context, the first official version of the new ?International Rock Excavation Data Exchange Standard? (IREDES) is being released. This new standard is a highly flexible data interface for exchange of information between production equipment and central computer systems. The standard was defined by global players in the mining industry and will soon be used to enhance local operations of global mining companies. Beside the standard definition now other aspects are coming into focus: The question how to design and how to implement IREDES compliant data exchange in practice. Implementation of IREDES covers the following aspects: !" Implementation on in-field production systems !" Communication and networking !" Implementation on databases and commercial IT systems In-field production systems are characterized by a big variety of different automation systems. Therefor, different IREDES implementation philosophies have to apply to those systems. One philosophy uses an integrated IREDES compliant automation system on every machine. The alternative method uses one shared IREDES compliant ?Proxy server? for a number of machines connected to this server using proprietary interfaces. Communication and networking can be integrated openly and independently from hardware infrastructures. The only precondition is that communication and networking has to be Ethernet - TCP/IP protocol compatible. IREDES Implementation on the commercial IT level means to exchange IREDES data sets with databases, simulation software, office packages and special applications. Interfacing is easy as long as the software or the database system provides an interface to the Extensible Markup Language (XML).

May 1, 2003

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By J. F. Butler

Boron nitride, BN, has been identified in boron low-carbon steels by means of light microscopy, electron microscopy and diffraction, and chemical analysis. This boron nitride is responsible for strain aging suppression in these steels through the removal of nitrogen from solution; however, small oxidizing potentials which result in deboronization In the austenitic temperature range also result in boron nitride decomposition and the subsequent occurrence of nitrogen strain aging. THE addition of boron to low-carbon steels is an effective means of eliminating the detrimental effects of strain aging;',' however, the mechanism by which boron suppresses strain aging has not been established. In studying the effect of heat treatment on the strain aging of boron low-carbon steels, Butler3 found that no detectable nitrogen was present in the ferrite solid solution after various heat treatments even though the total nitrogen analyses of the steels were 0.003 pct N. Apparently the function of boron in suppressing strain aging is the removal of nitrogen from solution to form a relatively stable second phase. A clue to the identity of this phase was found by Speight4 who extracted from an aluminum-killed boron steel an acid insoluble residue which contained boron and nitrogen in proportions corresponding to the compound, BN. Shyne and Morgan5 found that the addition of nitrogen to a hardenable boron steel lowered its hardenability in a manner which suggest-d the presence of nucleating particles (presumably BN) even at high austenitizing temperatures. Although this indirect evidence for the presence of boron nitride in boron steels has been found, the compound was not identified metallographically as a separate phase in these steels. Because boron has an affinity for oxygen comparable to that of silicon,5 boron steels must be thoroughly killed with aluminum in order to prevent the reaction of boron with oxygen.7 The affinity of boron for oxygen also is demonstrated through the ease of deboronization of a boron steel in an oxidizing atmosphere. Digges, Irish, and Carwile8 found that a mixture of wet natural gas and air caused both deboronixation and decarburization of a boron steel at 1900°F. The boron content rose at the surface of the steel due to the formation of boron oxide. Shyne and Morgan9 encountered deboronization at much lower oxygen potentials; loss of boron occurred in steels treated at 1750o F under argon purified to 0.0014 pct 0, even though decarburization did not occur. Boron oxide, B2O3, is much more stable than the nitride, BN, as is indicated by the standard free energies of formation at 980oC: -235 kcal per mol of B2O3 (liquid) and -28 kcal per mol of BN (crystal). It is evident that the oxygen potential must be kept low in the presence of BN in order to prevent its decomposition and the subsequent formation of B2O3' The purpose of the work described in this paper was to identify the nitride phase responsible for the removal of nitrogen from solution and to study its stability under oxidizing conditions. IDENTIFICATION OF BN In order to identify the phase containing boron and nitrogen, several alloys high in boron and nitrogen were made up in a small vacuum furnace. In alloys 3 and 4, Table I, electrolytic iron was used as a charge material. Boron additions were made in the form of 18 pct B ferro-boron after the iron was molten. In the case of alloy 3, the charge was solidified at this point; for alloy 4, nitrogen at 1 atm pressure was admitted over the melt before it was

Jan 1, 1962

By D Xiong, G Xu, L Yao, F Wang, Y Duan

The goal of this project has been to digitise and use drill parameter data from rotary drilling (measurement while drilling; MWD) for a more effective planning of the blasting process in surface mines. A more accurate and reliable digital drilling and automatic hardness identification technology was developed, which includes both a hardware and software system. In the aspect of hardware, we designed a positioning, navigation and hardness perception terminal system which consists of a global positioning system original equipment manufacturer board, programmable logic controller and sensors of measuring major parameters, and a wireless data transmission system which combines digital blasting platform and wireless transmission facilities. In the aspect of software, we developed the navigation software of locating blastholes using LabVIEW and C++, and the blasthole design software using AutoCAD ActiveX (C#) technologies. This new technology is applied at Jiangxi Dexing Copper Mine, and initially realising the digitisation of drilling and hardness identification in blasting zone.CITATION:Duan, Y, Xiong, D, Yao, L, Wang, F and Xu, G, 2015. Advanced technology for setting out of blastholes and measurement while drilling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds in Russell County , Va . Almost 2 million tons of coal was mined in 1961 ; 75 percent of the coal was cleaned mechanically in preparation plants in the county . The coal of Russell County is ranked as medium- to high- volatile bituminous , contains small amounts of sulfur , and generally requires some cleaning to reduce the ash content to limits acceptable for metallurgical purposes .

Jan 1, 1963

Politicians and economists talk glibly about the so-called knowledge revolution. The reality is that knowledge is fundamental to economic progress. Consequently there have been many technological revolutions. The global impacts of the invention of the steam engine and the development of the frozen meat industry are well known. Another less publicised technological advance occurred in Central Otago late in the nineteenth century. This was the adaptation of the bucketladder dredge to the mining of placer deposits. A product of over 30 years experimentation and innovation, New Zealand dredging technology was taken to the Risdon Iron and Locomotive Works, San Francisco by R H Postlethwaite, a Dunedin based mining engineer. New Zealand-style dredges built by Risdon operated successfully in California, Alaska and the Yukon. Californian engineers assimilated the best features of the New Zealand dredges with American (Bucyrus) designs to produce a standard for the worldwide placer mining industry.

Jan 1, 2003

mean to say that these explosions are mechanical, but that the ejectment of the stock, throwing out of tops, etc., are mechanical. I see no reason at present, although I have had almost no experience in the use of large quantities of Mesabi ore, to change my ideas on the subject. That these explosions should follow irregular working or slipping in the furnace, I think can be explained. I have noticed that immediately following slips there is little or no settling of the stock on top, although there is no lessening of the volume of gas passing into the stoves and boilers. Supposing that, after a slip of 3 or 4 feet, the filling continues, but for some distance from the 'top the stock fails to move: there would be a much better chance for the deposited carbon to clog interstices in the stock, and for the additional effect in the same direction of the fine ore in the charge, than if the stock were properly settling. Under such conditions it is easily supposable that the openings would be entirely closed, or closed so tightly that the pressure below the obstruction would be raised to a point approaching the blast-pressure, or to a point high enough to force a passage or an enlargement of the small passages which may remain. When this occurs, gas from below under pressure carries with it large quantities of deposited carbon and fine ore; if the case is aggravated, coke, stone, bell, etc. As soon as the red-hot deposited carbon meets the air there are perfect conditions for a dust explosion, which naturally follows, the same as in a coal-mine or flour-mill.

Jan 1, 1899

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By K. Meshinchi Asl

In this study the effects of T4 and T6 heat treatments on microstructural characteristics of AZ91 alloy containing Rare Earth elements have been investigated. Formation of intermetallic Al1 1RE3 needle shape particles which have a good thermal stability reduces both formation of ß(Mg17A112) and discontinues precipitation in AZ91 alloy which are dominated at the grain boundaries and are responsible for poor mechanical properties specially in elevated temperatures. For AZ91-RE samples both T4 and T6 heat treatments led to a continuous precipitation of ß particles at the grain boundaries after aging. However, in AZ91 samples (with no Rare Earths) precipitation was discontinuous at grain boundary areas. This type of precipitation is one of the main reasons of poor mechanical properties of this alloy at elevated temperatures.

Jan 1, 2007

Jan 1, 1970

Jan 1, 1955