Search Documents

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By Tamara Wiseman, David Stewart

"A Quarry located in Georgia is a green-field site established in 2011. The quarry lies in the eastern part of the Georgia Piedmont area. It is within a distinctive, northeast-trending belt of relatively high-rank metamorphic rocks known as the Kiokee Belt, a poorly mapped sequence of units that largely consists ofamphibolite and various schists and gneiss that are host for relatively young granite bodies andassociated pegmatite and aplite dikes."

Jan 1, 2017

By A. J. Beer, A. Wetherelt

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. Camborne School of Mines has developed a simple, cost-effective light-sectioning method that has been used successfully in tunnels and small stopes. Light sectioning provides an almost visual examination of the stope's excavated profile. An illuminated section of walls, roof and floor is recorded photographically. Overbreak and underbreak can then be easily quantified by reference to the designed shape. The prototype rig is described. Use of a fish-eye lens to capture a greater field of view is discussed. Calibration was achieved by comparison with images made with a conventional wide-angle lens with nominal distortion. The system is reliable under a range of operating conditions including dust, heat and humidity. It is also simple and easy to use, does not require skilled personnel and is low cost

Jun 18, 1905

By P. M. Swash

The paper describes the use of mineralogical methods in the exploration and evaluation of primary diamond occurrences. The most common methods that are used include the systematic search for kimberlitic indicator minerals, surface textural study of the indicator minerals, (garnet, spinel, ilmenite and chrome diopside) and alluvial macrodiamond studies so as to understand their provenance and guide exploration towards diamondiferous targets. The mineral chemistry of the indicator is used to positively assess the origin of the mineral grains and is also pivotal in the determination of the diamond potential of a deposit. Petrography of the primary deposit is able to identify the body to be kimberlitic and is also a support to the mineral chemistry findings. Unambiguous proof of a prospects potential to contain macrodiamond is proven by the occurrence of microdiamonds in the residues from the rock. The presence of a sufficient number of microdiamonds in the rock is enough to determine a semiquantitative grade estimate and warrant further metallurgical evaluation so as to determine its actual macrodiamond content.

Jan 1, 1991

By Chas. F. Jackson

This paper is a tabular compilation of data contained in a series of information circulars dealing with mining methods and costs at a large number of mines in the United States and some foreign countries. There circulars have been published from time to time during the years 1929 to 1934 inclusive. From time to time, as enough data became available in these circulars, other circulars and. bulletins have been published in which the data bearing upon different phases of nine operation were summarized, discussed, and analyzed. The present paper is a compilation of data on costs of drifting and crosscutting contained in earlier circulars, .designed to assemble this information in a convenient form for reference without attempting lengthy discussion of details of drifting and crosscutting practice. For such details the reader is referred to the circulars on individual mines.

Jan 1, 1935

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

Discussion of the paper of W. H. Gunniss, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2309 to 2310. PROF. J. W. RICHARDS, South Bethlehem, Pa. :-In regard to the physical nature of quartz for making silica brick, is the coarse-grained preferable ? E. P. MATHEWSON, Anaconda, Mont. :-A dense quartz is preferable. The quartzite is the actual material used by the Anaconda Company. The sandstone referred to, the foreign quartz, was a very pure sandstone and bad hardly any impurities in it, and the brick made from that particular material, while apparently beautiful while coming out of the kiln, and true, immediately on heating in the furnace buffed up half an inch and were cracked open.

Jan 11, 1913

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986

By Rick Hyndman

? Context: Ø Global action on climate change ? The situation of trade-exposed industry sectors ? The federal government?s draft plan for industry ? CAPP?s position ? Canadian emissions & Canada?s Kyoto target Simple Economic Theory of Dealing with Externalities ? Put cost on emissions Ø Carbon tax Ø Emission trading with auctioned permits ? GHG costs get reflected in the prices of energy alternatives, goods & services Ø Decisions driven by changes in relative prices ? Switching to lower emission fuels ? More energy efficient ways of producing ? More energy efficient appliances, cars, housing ? Reduced demand for energy intensive goods & services ? Anticipation of higher CO2 price drives low CO2 technology Development

Nov 1, 2002

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By J. B. Caine

THE investigation outlined in this paper was carried on at the plant of the Sawbrook Steel Castings Co., Lockland, Ohio. EFFECT OF TEMPERATURE In the study of the effect of temperature, heats were made with the Sawbrook company's standard practice, using multiple slags, the only difference' being that the heats were tapped at two temperatures; one group between 2960° and 3040°F and the other group between 3200° and 3250°F. Slags were weighed throughout the heat at each slag change and after the heat was poured. Only the significant slag weights, those of the total slag and the finishing slag, have been reported.

Jan 1, 1947

By George E. Peacock

Campbell Red Lake Mine is situated at Balmertown, in the Red Lake District of Northwestern Ontario, Canada. This area is some 120 miles north of the Trans Canada Highway and is some 160 miles Northeast of Winnipeg, Manitoba. The majority of our 300 employees live in Balmertown, which is a community of some 1,200 people, situated adjacent to the mine proper. The mine is serviced by a single shaft 4,300 feet deep. There are 27 levels at 150 ft. intervals. Stoping is being carried out down to the 20th level with only preliminary development having been done on the bottom 6 levels. The majority of our mill feed of 825 tons per calendar day comes from above the 10th level. Gold occurs as specks and streaks in bluish-grey to white quartz carbonate veins. It is extremely fine grained and most is invisible to the unaided eye. In addition to Gold the veins carry varying amounts of sulphides such as, Arsenopyrite, Stibnite, Pyrite, Pyrrhotite and Sphalerite. A minor amount of silver occurs as an impurity in the gold. Arsenopyrite is a marker for the gold ore at Campbell. The average grade of the mill feed is 0.7 oz. of gold per ton. The ore is dumped into an underground ore pass that feeds to a jaw crusher on the 20th level that reduces the rock to a maximum size of 4". This material is hoisted by skips to an ore bin in the head frame.

Jan 1, 1975

By William G. Doepken

GENERAL DESCRIPTION The Henderson mine utilizes a highly mechanized, continuous panel-caving system to extract ore from a deep, massive, molybdenum deposit. The mine site, lo¬cated 80.5 km (50 miles) west of Denver, is situated at 3170 m (10,400 ft) above sea level in a steep valley on the eastern side of the Continental Divide. The mill site, located on the western side of the divide, is linked to the mine via a 15.5-km (9.6-mile) railroad tunnel. Mine production is scheduled to reach 27 215 t/ d (30,000 stpd) from the uppermost production level. This pro¬duction rate will have been reached within the four years following an intensive ten-year preproduction development program. A second production level, due to come on stream in later years, will expand production capabilities to 31 751 t/d (35,000 stpd). The mine, which employs approximately 2000, has blocked-out ore reserves of 220 Mt (242 million st) at an average grade of 0.42% MoS2. Geology The Henderson deposit is composed of two partially overlapping ore bodies that lie 1080 m (3600 ft) beneath the peak of Red Mountain. The ore bodies are entirely within a Tertiary rhyolite porphyry intrusive complex that has intruded Precambrian granite. The de¬posit is elliptical in plan with overall dimensions of 670 x 910 m (2200 x 3000 ft). In section it is arcuate with an average thickness of 185 m (600 ft). The top of the deposit is at an elevation of 2610 m (8700 ft) while the lower limits range from 2340 m (7800 ft) on the west to below 2100 m (7000 ft) on the east. The mineralization is relatively continuous in the ore bodies and consists of molybdenite and quartz in random to subrandom, intersecting, closely spaced veinlets. Cavability RQD (rock quality designation) * values measured from Henderson drill core and compared with the RQD values from the Climax and Urad block-cave mines in¬dicated that the Henderson ore would cave but with difficulty and that a high percentage of the cave ma¬terial would be blocky. Initial caving experience shows the Henderson ore caves easier and with greater frag¬mentation than was indicated by the RQD values. Pos¬sible reasons for this are: 1) The greater lithostatic load at the Henderson has a greater effect on caving and fragmentation than anticipated. 2) The relief of confining pressure due to caving action and brittleness of the rock is enhancing breakage. Mine Layout The Henderson mine layout was designed from its inception for a large-scale, rubber-tired, continuous panel-caving mining system. The ore body is vertically divided into three major mine levels (Fig. 1). The top¬most level (8100 level), which is 2469 m (8100 ft) above sea level, is the current mine production level. The intermediate or 7700 level, which is in the initial

Jan 1, 1982

By A. J. Mcintosh

PRICE changes in competing fuels in the last three decades have reflected the changes in the consuming habits of the people of the United States. Prior to World War 11 the importance of fuel oil and fuel gas increased almost constantly while the relative importance of both bituminous and anthracite coal decreased. During this same prewar period coal prices increased to a much greater extent than oil prices. In fact, in many years, oil prices declined and in most cases are now no higher than they were back in 1925-26. During the war natural economic trends were entirely upset because of the tremendous petroleum requirements of the Army and Navy. Under these conditions many industrial plants were converted to the use of coal and the new installations in home heating and industrial plants of all kinds which might have used oil were practically eliminated. Although petroleum prices were rigidly controlled by OPA coal prices increased several times during the war. An over-all statement as to the rela-

Jan 1, 1947

By Benjamin N. Webber

THE peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guanacaste, which is the northern of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guayjiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. PHYSIOGRAPHY In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active: (2) the Atlantic low-lands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from o to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. HISTORY AND PRODUCTION The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1942

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By G. L. Oldright

This paper is the fourth of a series of preliminary papers on smelting in the lead blast furnace.4 The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation and to correlate these conditions with operating factors, furnace behavior, and metallurgical losses. ACKNOWLEDGMENTS The authors wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, for their whole-hearted cooperation in this investigation.

Jan 1, 1929

By E. Poiate, P. R. Cabral, A. V. N. Santos, P. V. M. Costa, C. S. Amaral, A. M. Costa

This paper discusses the design of underground salt caverns, opened by solution mining, for the production of brine and storage of natural gas under high pressures. The caverns are located in the salt basin in Maceio City, Alagoas State, at the northeast region of Brazil. Special attention is given to the geomechanical structural design of the caverns using computer codes specially developed for the simulation of excavations in salt rock formations, considering validated constitutive creep laws under different initial stress states and temperatures. The behavior of sedimentary rocks intercalations presented in the salt layer is simulated using elastic-plastic models. The excavation of the caverns by solution mining is also simulated starting from a geostatic initial equilibrium state of stresses, with a unique formulation only implemented in these computer codes, without the need of the application of boundary stresses to the model in order to develop the initial state of stresses. These computer codes have being used in the design of several clusters of caverns for brine production used as raw material of Poly Vinyl Chloride (PVC) of the Chemical Industryin Brazil. These computer codes and methodology were also applied to the design of the underground conventional potash mine in the state of Sergipe, overlying tachyhydrite and carnallite with very high creep strain rate. They have also been used in the design of the pre-salt oil wells through thick layers of stratified salt rock in Santos Basin, for the exploration and production of the pre-salt reservoirs in Brazil. The constitutive creep equations implemented in the codes are based on a double mechanism creep law. The creep constants adopted in the simulation are taken from a previous investigation carried out on an experimental panel of the potash mine, considering the stratified geology with different salt rocks of the basin where the mine is located. These constants were also obtained by lab tests under different confined and differential stresses and temperatures.

Jan 1, 2015