Search Documents

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions' it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919

By John Nagy

A study was made in the Bureau of Mines experimental coal mine of factors affecting gas ignition by a cutoff explosive charge. Experiments showed that, although gas could be ignited under some circumstances, the probability under normal mining conditions would be low. The use of permissible explosives, relatively short-delay intervals in firing adjacent holes, blasting to a 6-inch kerf, and reasonable care in the placement of the holes favor safe blasting and are current practice in mining. The experiments also showed that the weight of the charge is not a primary factor in the ignition of gas by a cutoff charge. The quenching action of a first charge on the igniting action of a second was verified in a supplementary study. Related experiments have shown that gas at the face may be ignited by a single charge of explosive when fired with a light coal burden. Permissible explosives were less hazardous under these conditions than nonpermissible explosives. The frequency of gas ignition in cutoff and single-charge experiments increased as the linear distance between the sheared face and the opposing mine rib increased.

Jan 1, 1960

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By R. W. Schenker

INTRODUCTION Environmental and occupational safety and health requirements often have a major impact on the design of comminution circuits, leading to increased capital and operating costs and reduced income. A project's capital cost can be increased by environmental permitting delays and the addition of dust collection equipment. Income can be reduced by lost production during unscheduled plant shutdowns for dust collection equipment maintenance. Dust collection equipment must be carefully selected and sized to minimize impact on the project. The equipment performance must comply with environmental regulations and allow working areas to comply with occupational safety and health regulations. Unnecessary overdesign could jeopardize the project's desirability from an economic standpoint. The equipment must be sufficiently reliable to avoid interference with production schedules. This chapter provides practical information on the selection and sizing of comminution circuit dust collection equipment that is consistent with the requirements stated above. It presents information on the reasons and general principles of dust collection; various types of dust collection equipment; and design criteria for ventilation hoods, duct systems, fabric filter dust collectors, and fans. An example discussing the selection and sizing of dust collection equipment for a simple comminution circuit is also presented. REASONS FOR DUST COLLECTION Dust collection equipment should be installed in comminution circuits for a variety of reasons, some of which are discussed below. These include compliance with government regulations, minimization of housekeeping requirements, product recovery, and improvement in public and employee relations. Compliance with Government Regulations Dust emissions from comminution circuits must comply with both air pollution control and occupational safety and health regulations. The regulations that may influence the selection of comminution circuits are discussed in more detail in Chapter 2. Air pollution control regulations limit the emission of dust, as well as visible emissions to the atmosphere and the concentration of dust in the ambient air. These regulations minimize the degradation of air quality and impact to other environmental considerations such as the health of the general public,

Jan 1, 1982

By Chen Dong, Yang Wenwang, Liu Zhineng, Tan Ming

"To meet the requirement of production expanding of a certain potash ore dressing plant in Xinjiang province of China, industrial test of XCF/KYF-50 flotation machine was performed to process potash ore. The tank of XCF/KYF-50 flotation cell is in U shape, 50m3 of volume. This flotation cell is able to suck slurry by itself, and can be arranged on the same base level without high difference. In this paper, two sets of XCF/KYF-50 flotation cells were adopted to replace 8 sets of 8m3 flotation cell in original flow sheet of flotation. Aeration rate, slurry suction capacity, power consumption and slurry suspension are investigated. The measuring results show the slurry suction capacity of the flotation cell is larger than 12.80m3/min and solid particles disperse evenly in the tank without deposition. Industrial test result indicates that the final grade of concentrate is 26.69% at the recovery of 90.95%, which is up to expected performance. XCF/KYF-50 flotation cell has advantages of high flotation efficiency, significant energy saving and reasonable configuration of automatic control system, this kind of flotation cell can meet the requirement of production expanding of this potash ore dressing plant well."

Jan 1, 2014

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

The Tuesday morning session opened at 9:00 a.m. and was presided over by Mr. Homer Hyatt, Safety Director, North American Coal Corporation, Western Division, Castle Gate, Utah. Mr. Hyatt introduced Mr. Richard F. Walker, Vice President, Engineer & Planning, Electric Department, Public Service Company of Colorado, Denver, Colorado. Mr. Walker is a native of the State of Nebraska, a graduate of the University of Colorado with a BSEE degree in 1949. He has been associated with the Public Service Company of Colorado for almost twenty years and in the above capacity for the last one and one-half years. Mr. Walker?s subject was "Our New Plants and Coal. (See index for printed text of Mr. Walker's paper.) Mr. John F. O'Leary, Director, U.S. Bureau of Mines, Washington, D. C. spoke on the ?High Cost of Economy.? Mr. O'Leary graduated from George Washington University in 1950 with a degree in Economics. In 1950, he joined the Bureau of Mines. In 1963 he was appointed Deputy Assistant Secretary, Mineral Resources, U.S. Department of the Interior. In 1967, he was appointed Chief, Bureau of Natural Gas, Federal Power Commission. In 1968, appointed Director, U.S. Bureau of Mines, Washington, D.C.

Jan 1, 1969

By Tadeu Messias Donizete Borba

A soldagem com elevado aporte térmico é uma das alternativas adotadas pelos estaleiros para aumento da produtividade nas operações de união de materiais. No entanto, os ciclos térmicos gerados durante a soldagem podem provocar transformações microestruturais prejudiciais à tenacidade na zona afetada pelo calor (ZAC). Este estudo teve como principal propósito realizar a caracterização microestrutural e avaliar as propriedades mecânicas da ZAC do aço naval Sincron EH36 produzido na Usiminas por laminação controlada seguida de resfriamento acelerado em comparação com um aço de mesma classe de limite de escoamento produzido convencionalmente, ambos soldados pelo processo ao arco submerso em dois níveis de aporte térmico: 76 e 130 kJ/cm. Foi observado que a presença de uma microestrutura mais refinada nas diferentes regiões da ZAC, associadas ao menor tamanho de grão do metal base e ao menor carbono equivalente, foram os principais fatores que contribuíram para a excelente tenacidade da ZAC do aço Sincron em comparação ao aço convencional. Os resultados obtidos mostraram que é possível obter juntas soldadas com excelentes propriedades mecânicas ao se empregar aço Sincron para a soldagem com altos aportes de calor, e sua utilização pode ser uma estratégia para otimização dos tempos e custos de fabricação na indústria naval.

Aug 8, 2018

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By Clarence E. Jackson, George G. Luther

The ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepaxed with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. 2, the angle at maximum load in lour cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By James F. Kemp

The iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. Previous Work In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the time Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 1, 1916

By G. H. Turner, R. C. Bell, E. Peters

Zinc oxide activities in a typical lead blast furnace slag have been calculated from plant operating data. These activities were used to assess the probable effect of fuel composition, oxygen enrichment, and air preheating on the efficiency and capacity of the slag-fuming operation. THE physical chemistry of zinc fuming has been examined with three objectives in mind: 1—to predict conditions favorable to increasing furnace capacity, 2—to predict the changes required to fume zinc more economically, and 3—to explain reported differences in the efficiencies of various slag-fuming plants. This study, made at ail in the plants and laboratories of The Consolidated Mining and Smelting Co. of Canada Ltd., developed from a program undertaken some three years ago on behalf of the AIME Extractive Metallurgy Div. subcommittee on slag fuming. Lead metallurgists first became interested in the recovery of zinc from lead blast furnace slags in 1905 and 1906. An excellent review of the early experimental work has been made by Courtney,' who described blast furnace, reverberatory furnace, and converter methods of fuming zinc from slag. Some of the investigators did not appreciate the importance of reducing the zinc oxide content of the slag to metal in order to fume it, since they tried compressed air blast without fuel in their earliest attempts. However, by 1908, the importance of reducing the zinc was established.' In 1925, the Waelz process for the recovery of zinc oxide from oxidized zinc ores was developed in Germany.' This process was not readily adaptable to lead blast furnace slags because of the difficulty in handling fusible charges in a kiln. What appears to have been the first slag-fuming operation as it is known was commenced by the Anaconda Copper Mining Co. at East Helena, Mont. in 1927." The first Trail furnace was completed in 1930, and this was followed by the construction of several other slag-fuming plants. During the period in which slag fuming has been extensively employed, little development of the chemistry of this process as a whole has taken place. Several good papers on the petrography of lead blast furnace slags have been published,""= but these studies could do little more than establish the forms in which lead and zinc occur in the initial charge and final products of the slag-fuming operation. In recent years, zinc-smelting problems have been ap- proached from a thermodynamic point of view. Maier has published an excellent thermodynamic treatment of zinc smelting." The important thermodynamic properties of zinc and its compounds have been determined and checked by other investigators.' However, to the best of the authors' knowledge, no thermodynamic treatment of the fuming of zinc from slag has been published. A thermodynamic study of any process requires that the essential chemistry of that process be known. In slag fuming there appear to be some differences of opinion as to whether the active reducing agent is elemental carbon or carbon monoxide. Furthermore, some observers have noted that high volatile coals appear to be more efficient than low volatile coals, indicating that hydrogen is also an important factor in the reducing efficiency of a fuel. That both hydrogen and carbon monoxide are effective reducing agents for the zinc oxide content of lead blast furnace slags can be demonstrated readily by introducing these gases into a slag bath held in a neutral vessel at 2100°F (1150°C). Elemental carbon also will reduce zinc oxide, but it is improbable that much free carbon is available for reduction of zinc, as the reaction between the finely powdered coal and air should be largely completed before the solid coal particles reach the slag. Some large-scale fuming experiments using gaseous hydrocarbons have been carried out by other investigators, but, as far as is known, these have not been developed yet into operating processes. The thermodynamic treatment in this paper is based on the following reactions: 1—to supply the thermal requirements C+V2O2- CO [1] C + 0,-CO, [2] H2+ ~z0,-H,O 131 and 2—to reduce ZnO ZnO + CO + Zn + CO, c41 ZnO + H, e Zn + H,O. [51 The furnace-gas composition also is controlled by the equilibrium constant of the familiar water-gas reaction H,O + CO + CO, + H2. C6l In order for the thermodynamic calculations to be quantitatively applicable, it is necessary that the chemical reactions to which they are being applied

Jan 1, 1956

By C. G. Goetzel

Until recently porous bronzes have found many applications for self-lubricating bearings in the automotive, electrical, household appliance and general machine industries. The bulk of an annual production of several million pounds of copper powder had gone into the manufacture of these articles, of which by now more than a billion are in service. However, the war has brought severe curtailment of these bearings because of the scarcity of the two main constituents, copper and tin. The development of substitute materials of equal or superior properties has led to a large-scale replacement by products made from iron powder. In spite of the diminished interest in powdered copper-tin alloys caused by this trend, it was believed worth while to investigate some mechanical properties of these materials as a reference base for substitutes. In addition, experiments using the hot-press method were incorporated to investigate possibilities of saving vital equipment or opening new fields of applications. It must be assumed that by this time the powder metallurgy process of making porous bronzes, a development that found its first industrial applications more than 10 years ago, is well known in engineering. The patent literature and bibliography is volu- minous, most publications referring to porous, self-lubricating bronzes, containing about 10 per cent tin and I to 5 per cent graphite, with porosities in the range of 25 to 35 per cent.l-7 The excellent antifriction properties of these bearings, caused by the uniform impregnation with oil, are dependent on the interconnection of the pores and the uniform distribution of the graphite inclusions. The sintering mechanism of porous bronze, with its structural changes during the transformation of the metal powder into the sintered bearing has been shown in colored photomicrographs by Hall.* Diffusion between copper and tin was found to begin within one minute, when tin-rich transitory phases were formed. After 25 min. a homogeneous matrix of alpha was reached for an alloy containing 9.5 per cent tin and 6 per cent graphite. Price, Williams and Garrand,9 studying certain metal powder combinations in which sintering is accompanied by the cementing action of a liquid phase, including a 90-10 bronze sintered at 925°C., have found that if the treatment is carried out within the liquidus and solidus temperature range of the system, a peculiar process of alternate solution and precipitation occurs. The particles of the major solid constituent are dissolved in the minor liquid phase, but thereafter are reprecipi-tated on certain nuclei, which develop into large grains, usually rounded.

Jan 1, 1945

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By T. J. White

A synthetic Mineral Immobilization Technology (SMITE) has been developed for stabilizing municipal and hazardous waste incinerator ash. Tailored additives are introduced to the ash in a' first stage that pre-stabilizes all the toxic metal components in non-volatile forms. and in a second pyrometallurgical stage, these are converted to insoluble mineral analogues. It has been found that a combination of apatitie. spinal, anhydrite and monazite can immobilize all the ash components at high waste loading and high density. Typically the stabilized products contain in excess of 50 wt% ash and have densities of 2.5- 3.0 g.cc-1. Toxicity Characteristic Leach Procedure (TCLP) testing has demonstrated that the products well satisfy regulatory requirements. The cost of production and disposal of SMITE waste forms in 2-5 less expensive than. convential methods of solidification/stabilization. This paper will describe the principles of SMITE design for ash stabilization, outline the fabrication procedure, and present comprehensive microstructural and chemical data to validate waste form performance.

Jan 1, 1996

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963