Search Documents

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 ('other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

By Richard R. Klimpel

During the last 28 years, I have had the very challenging and rewarding experience of working as an engineering professional in a large multinational company, both as a manager of engineers and engineering projects as well as an inventor and generator of new engineering processes and products. Due to the diversified geographic and tech¬nical nature of my employer's business, my responsibilities have taken me all over the world. This has included interactions with people in different industries including minerals, coal, chemicals, petroleum, pulp and paper, agriculture and pharmaceuticals. As diverse as my experience may seem, it has always amazed me how common the basic underlying technology and economic trends are that shape the working environment that any given engineer in any given geographic loca¬tion will experience. I would like to discuss the industrial evolution from micro to macro engineering. One of the basic truths behind how industry must and will operate is "change," including: • the creation of conditions for change, • the anticipation of change, • the resistance to change, • the rewards that being part of a change can bring and • the destruction that change can bring to the unprepared. This fact was well stated by Heractitus around 500 BC.: "There is nothing permanent except change." This simple truth has been valid since the dawn of time and, if anything, is accelerating in nature every decade.

Jan 1, 1993

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

By Jean Goldschmidt

Recycling of fine oxidized particles of non-ferrous metals usually cannot be carried out by pyrometallurgical methods. 'Hydrometallurgy provides an alternative technology to reintroduce? the resulting products as secondary raw materials into the industrial cycle, thereby saving resources and energy while keeping the environment a little cleaner. The paper summarizes the methods employed by Hydrometal to achieve these objectives and? stigmatizes the latest counterproductive international regulations which create ever more obstacles to environmentally sound recycling.

Jan 1, 1995

By Thomas R. Kuesel

All engineering designs are based on assumptions regarding the behavior of the structure or facility being designed. These assumptions may be based more or less heavily on theory, but are credible only if verified by observations of field performance. Dr. Peck's "State-of-the-Art" paper has described the semi -empirical process of soft ground tunnel design, emphasizing the importance of records of field performance of actual projects constructed under a variety of conditions. This paper will present the principal results obtained from measurements made during construction of the soft ground tunnels for the San Francisco Bay Area Rapid Transit System. SCOPE The BART System comprises 75 route miles, including 14 miles of soft ground tunnelled subways in San Francisco, Oakland, and Berkeley. All tunnels are single-track sections, approximately 18 feet in diameter. Usually there are two parallel tunnels at the same level, but under Market Street in San Francisco there are four tunnels (two over two), and there is also a three-track section (two over one) in Broadway, Oakland.

Jan 1, 1997

By C. E. McFarland, N. W. Kirshenbaum

Cortez Gold Mines is located about 75 miles southwest of Elko, NV. Activity in the mining district dates from 1862. The current operation developed from a 1963 joint venture of Webb Resources, The Bunker Hill Company, Vernon F. Taylor, Jr., and American Exploration & Mining Co. Three years later, the USGS discovered gold on the property following a regional geochemical survey. Drilling in 1966 and 1967 identified 3.4 million st of oxide ore grading 0.28 oz Au/st, and a 1700 st/day countercurrent decantation mill was commissioned in 1969. Heap leaching started in 1971 on low grade ore and continues to the present. The mill was shut down in 1976 following exhaustion of known oxide reserves. Mobile equipment was sold and the proceeds committed to local exploration. In 1980, a new plan of operations was developed starting with existing low grade and newly discovered mill ore. The mill resumed operations in 1981 and has been operating to date. A series of metallurgical innovations, culminating in the commissioning of a new fluid bed roaster in the summer of 1990, has enabled treatment of a series of increasingly refractory ores. Current partners in the venture are Kennecott Corporation, Vernon F. Taylor, Jr., and Placer Dome U.S. Inc., manager of the operation. Idaho Mining Corp. holds a 7.5% carried interest.

Jan 1, 1992

Frank Firmstone, Easton, Pa. (communication to the Secretary*) : It may not be amiss to point out that the top-pressure in iron blast-furnaces is largely affected by variations in the temperature of the gas. I find in my note-books, cases in which the pressure was from 9.25 to 9.5 in. of water when the material in the furnace was low (after dinner-hour), which fell to from 8 to 8.5 in., when the furnace was again full, and the gas consequently cooled. The chief cause for this effect is, that, at the higher temperature, there is a decrease in the weight of the gas in the descending-leg of the siphon formed by the down-comer and the chimneys. It does not seem probable that there is any direct relation between top-pressure and quantity of flue-dirt. Top-pressure, at any given moment, measures the " head " necessary to discharge the gas then passing, against the resistances of pipes, valves, etc., in the gas-conduits between the top of the furnace and the mouths of the chimneys, and can be increased at will by closing, more or less, the valves, or dampers, at the stoves and the boilers. The question of relation between top-pressure and flue-dirt can be settled very easily by direct experiment, working alternately with gas-valves open, and partly closed, and noting the top-pressures and the respective quantities of fluedirt collected. The quantities of fine ore blown away, as shown by Mr. Grammer's tables, are astonishing to one who has had no actual experience with Mesabi ore and hard driving. Flue-dirt, in the sense in which he uses the term, was unknown at anthracite furnaces so long as the working was normal; when it did occur, it was always an incident of scaffolding and bad work, and was no doubt caused by an increase in the velocity

Jan 1, 1904

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By Romulo Camata

O objetivo deste trabalho é estudar as reações de dessiliciação, envolvidas no processo de pré-tratamento de ferro-gusa. A princípio, as misturas utilizadas foram caracterizadas e estudadas através do software de termodinâmica computacional (FactSage). Em seguida, os resultados obtidos através do estudo termodinâmico computacional foram comparados com aqueles obtidos mediante os testes experimentais a 1400 °C. As misturas dessiliciantes tiveram como base fontes de CaO e FeO. Os testes experimentais permitiram identificar que a agitação do sistema, maior quantidade de massa de mistura adicionada e misturas com adição de 20% de fonte de CaO mostraram-se mais eficazes no processo de dessiliciação do ferro-gusa. Com os resultados pode-se afirmar que a termodinâmica computacional mostrou-se eficaz em prever o processo. Além disso, a termodinâmica computacional também contribui, em alguns casos, para a análise de compostos sólidos que podem se formar na escória e limitar as reações de dessiliciação.

Oct 30, 2017

By E. T. Dumble

(Cleveland Meeting, October, 1912.) FOR many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries -west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gonzales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in it rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few, exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure-possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitic division of the Eocene, with lignite, shells of iron, etc.

Oct 1, 1912

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By Prodyot Kumar Ray, Sudip Kumar Koley, Aminul Islam, Somnath Banerjee

One of the most important topics in the construction industry is the building of railway embankments. Being such a delicate and significant structure, it is crucial to properly design the embankment and build it while adhering to all statutory criteria and design guidelines. A railway embankment's subsoil condition and fill material, groundwater table, dynamic and static loads during operation, and embankment geometry are some of its most crucial design considerations. This paper discusses the likely causes of the collapse of a railway embankment in eastern India as well as the suggested rehabilitation scheme. It was observed that an embankment collapsed in the aforementioned area during a inccesent rain. Along with the side shifting of a cantilever retaining wall that was positioned at the bottom of the embankment, the embankment next to the railroad track settled vertically. According to the available geotechnical report, the sub soil strata in half of the area adjacent to the embankment profile, where the embankment height gradually decreases from maximum height, is stiff to hard clay with an undrained cohesion value of around 50 kpa followed by dense sand, and the sub soil strata in the other half is soft clay with an undrained strength of 15 kpa. As a result, in the rainy season due to the sudden increase in the water table, the self-weight of the embankment increased and further caused the under-laying soft clay to get squeezed away and settle. Due to this squeeze/settlement effect of the soft clay layer, the retaining wall got disturbed along with the generation of an undulated embankment top profile. As a remedial measure, it is proposed to construct a contiguous bored pile wall at the toe of the embankment to stabilize the slope, and additionally, compaction grouting is recommended beneath the embankment to improve the soft clay. In order to carry out the analysis, certain commercial geotechnical software like Slide, Wallap, and Plaxis 2D are used. The factor of safety of the embankment slope considering the above restoration scheme is adequate under static and seismic conditions.

Sep 1, 2022

By Frank G. Wickert

One key to maintaining successful mining operations in today?s global economy is in having the ability to access real-time machine operating data ([1] G. Brown, B. Ebacher, W. Koellner,2000)([2] Brochure of Siemens E&A, Order Number 141000-1). With recent and ongoing advances in mining equipment systems it is imperative that mine managers have full knowledge of the status of their equipment at any given point in time. This knowledge is critical to ensuring that the productivity of each and every machine is maximized. Knowledge of machine status is only the first step, however, in controlling and optimizing a piece of mining equipment. Computer based diagnostic systems, traditionally offered on mining equipment, have provided a link for collecting data and trouble-shooting problems as they occur. One problem existed, though, that those systems stopped short of providing full drive systems access. A maintenance technician could see the data but to make critical adjustments or make repairs the technician needed to be on the machine. In extreme cases the machine would be down until OEM assistance could reach the mine site. The key then to reducing down-time and maximizing machine productivity was creating a system that could not only monitor drive systems but also provide remote access to those systems. Essentially a link needed to be created through which a technician could gain drive access remotely then make adjustments or repairs without being on the piece of equipment. This paper will introduce AccessDirectTM, a new remote diagnostic system for Bucyrus mining shovels and draglines. AccessDirectTM combines all three important elements of remote diagnostics: ? Vital Signs and Production Monitoring (SiRAS-M) ? Automatic analysis (SiRAS-A) of faults, and tracking of trends for preventive and reliability centered maintenance , and ? Fast, direct Intervention (SiRAS ? I) for troubleshooting support, repairs, and system optimization.

May 1, 2002

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985

By John C. Ferm

Although roof falls account for approximately half of the fatalities in underground coal mining, the factors that produce them are not clear. Mining methods can account for some, but in others the controlling factors are the geological setting in which the mining takes place. The present investigation was undertaken to determine the kinds of rocks that were most likely to produce roof problems. Such knowledge would be helpful to mine planning since rock samples can be obtained in advance of mining by core hole drilling. The investigation was undertaken in underground mines in the Pocahontas #3 seam in southern West Virginia and southwestern Virginia. The Pocahontas #3 is one of the most widespread in this region and is a major source of high quality metallurgical coal. There are at least ten very large mines in the area and many smaller ones. The region has a very long mining history and considerable experience has been gained in roof control problems. The study was conducted with the support of the U. S. Bureau of Mines.

Jan 1, 1978

By W. R. Purcell

An apparatus is described whereby capillary pressure curves for porous media may be determined by a technique that involves forcing mercury under pressure into the evacuated pores of solids. The data so obtained are compared with capillary pressure curves determined by the porous diaphragm method, and the advantages of the mercury injection method are stated. Based upon a simplified working hypothesis, an equation is derived to show the relationship of the permeability of a porous medium to its porosity and capillary pressure curve, and experimental data are presented to support its validity. A procedure is outlined whereby an estimate of the permeability of drill cuttings may be made with sufficient acuracy to meet most engineering requirements. INTRODUCTION The nature of capillary pressures and the role they play in reservoir behavior have been lucidly discussed by Lev-rett', Hassler, Brunner, and Deah12, and others. As a result of these publications the value of determining capillary pressure curves for cores has come to be generally recognized within the oil industry. While considerable attention has been directed toward the subject in an effort to provide a reliable method of estimating percentages of connate water, it has been recognized that capillary pressure data may prove of value in other equally important applications. This paper describes a method and procedure for determining capillary pressure curves for porous media wherein mercury is forced under pressure into the evacuated pores of the solids. The pressure-volume relationships ob- tained are reasonably similar to capillary pressure curves determined by the generally accepted porous diaphragm method. The advantages of the method lie in the rapidity with which the experimental data can be obtained and in the fact that small, irregularly shaped samples, e.g., drill cuttings, can be handled in the same manner as larger pieces of regular shape such as cores or permeability plugs. Based upon a simplified working hypothesis, a theoretical equation will be derived which relates the capillary pressure curve to the porosity and permeability of a porous solid, and experimental data will be presented to support its validity. This relationship aplied to capillary pressure data obtained for drill cuttings by the procedure described provides a means for predicting the permeability of drill cuttings. METHODS FOR DETERMINING CAPILLARY PRESSURES Several techniques have so far been employed in determining capillary pressure curves and these fall into two principal categories: (1) Liquid is removed from, or imbibed by, the core through the medium of a high displacement pressure porous diaphragm (2) Liquid is removed from the core which is subjected to high centrifugal forces in a centrifuge4,'. There are? however, certain limitations inherent in both methods. The greatest capillary pressure which can be observed by method (I), above, is determined by the maximum displacement pressure procurable in a permeable diaphragm which at the present time appears to be less than 100 psi. An even more serious limitation of the diaphragm method is imposed hy the fact that several days may be required to reach saturation equilibrium at a given pressure; hence, the time re- quired to obtain a well-defined curve may be measured in terms of weeks. Furthermore, to date, no suitable technique for handling relatively small, irregularly shaped pieces of rock, such as drill cuttings, has been reported and, therefore, measurements must be made, in general, on cores, or portions thereof. The centrifuge method offers the distinct advantage over the porous diaphragm method of arriving at saturation equilibrium in a relatively short time by virtue of the elimination of the transfer medium for the liquid. The calculation of capillary pressures from centrifuge speeds is somewhat tediousa, however, and the equipment required is fairly elaborate. While there exists the possibility that this method might be adaptable to the determination of the capillary pressures of cuttings, this particular ramification has not been investigated, as far as is known. In view of the limitations of the two principal methods for determining capillary pressures, the apparatus described in the following sections has been devised in order that difficulties previously encountered might be circumvented. MERCURY INJECTION METHOD FOR DETERMINING CAPILLARY PRESSURES Theory The methods described above for determining capillary pressures are characterized by the fact that one of the fluids present within the pore spaces of the solid is a liquid which "wets" the solid, i.e., the contact angle which the liquid forms against the solid is less than 90" as measured through that phase. For these "wetting" liquids the action of surface forces is such that the fluid spontaneously fills the voids within the solid. These forces likewise oppose the withdrawal of the fluid from the pores of the solid.

Jan 1, 1949

By W. R. Purcell

An apparatus is described whereby capillary pressure curves for porous media may be determined by a technique that involves forcing mercury under pressure into the evacuated pores of solids. The data so obtained are compared with capillary pressure curves determined by the porous diaphragm method, and the advantages of the mercury injection method are stated. Based upon a simplified working hypothesis, an equation is derived to show the relationship of the permeability of a porous medium to its porosity and capillary pressure curve, and experimental data are presented to support its validity. A procedure is outlined whereby an estimate of the permeability of drill cuttings may be made with sufficient acuracy to meet most engineering requirements. INTRODUCTION The nature of capillary pressures and the role they play in reservoir behavior have been lucidly discussed by Lev-rett', Hassler, Brunner, and Deah12, and others. As a result of these publications the value of determining capillary pressure curves for cores has come to be generally recognized within the oil industry. While considerable attention has been directed toward the subject in an effort to provide a reliable method of estimating percentages of connate water, it has been recognized that capillary pressure data may prove of value in other equally important applications. This paper describes a method and procedure for determining capillary pressure curves for porous media wherein mercury is forced under pressure into the evacuated pores of the solids. The pressure-volume relationships ob- tained are reasonably similar to capillary pressure curves determined by the generally accepted porous diaphragm method. The advantages of the method lie in the rapidity with which the experimental data can be obtained and in the fact that small, irregularly shaped samples, e.g., drill cuttings, can be handled in the same manner as larger pieces of regular shape such as cores or permeability plugs. Based upon a simplified working hypothesis, a theoretical equation will be derived which relates the capillary pressure curve to the porosity and permeability of a porous solid, and experimental data will be presented to support its validity. This relationship aplied to capillary pressure data obtained for drill cuttings by the procedure described provides a means for predicting the permeability of drill cuttings. METHODS FOR DETERMINING CAPILLARY PRESSURES Several techniques have so far been employed in determining capillary pressure curves and these fall into two principal categories: (1) Liquid is removed from, or imbibed by, the core through the medium of a high displacement pressure porous diaphragm (2) Liquid is removed from the core which is subjected to high centrifugal forces in a centrifuge4,'. There are? however, certain limitations inherent in both methods. The greatest capillary pressure which can be observed by method (I), above, is determined by the maximum displacement pressure procurable in a permeable diaphragm which at the present time appears to be less than 100 psi. An even more serious limitation of the diaphragm method is imposed hy the fact that several days may be required to reach saturation equilibrium at a given pressure; hence, the time re- quired to obtain a well-defined curve may be measured in terms of weeks. Furthermore, to date, no suitable technique for handling relatively small, irregularly shaped pieces of rock, such as drill cuttings, has been reported and, therefore, measurements must be made, in general, on cores, or portions thereof. The centrifuge method offers the distinct advantage over the porous diaphragm method of arriving at saturation equilibrium in a relatively short time by virtue of the elimination of the transfer medium for the liquid. The calculation of capillary pressures from centrifuge speeds is somewhat tediousa, however, and the equipment required is fairly elaborate. While there exists the possibility that this method might be adaptable to the determination of the capillary pressures of cuttings, this particular ramification has not been investigated, as far as is known. In view of the limitations of the two principal methods for determining capillary pressures, the apparatus described in the following sections has been devised in order that difficulties previously encountered might be circumvented. MERCURY INJECTION METHOD FOR DETERMINING CAPILLARY PRESSURES Theory The methods described above for determining capillary pressures are characterized by the fact that one of the fluids present within the pore spaces of the solid is a liquid which "wets" the solid, i.e., the contact angle which the liquid forms against the solid is less than 90" as measured through that phase. For these "wetting" liquids the action of surface forces is such that the fluid spontaneously fills the voids within the solid. These forces likewise oppose the withdrawal of the fluid from the pores of the solid.

Jan 1, 1949

By Heimo Thalhammer

During the refining of lead, copper or other metals the furnaces used in the process · often produce waste gases. This paper illustrates how these waste gases can be successfully treated and destroyed by CTP 2-bed or multi-bed compact systems, modified for the additional reduction of dioxins and furans. The CTP regenerative thermal oxidizer also destroys voes (organic compounds and odours) using ceramic blocks as a heat exchanging media. The raw gas is forced through the ceramic beds where it is heated up to the oxidation temperature level. The voes, dioxins and furans are destroyed in the combustion chamber, subsequently generating water, eo2 and heat. The hot purified gas heats up a second ceramic bed, which is used to preheat the raw gas after the valves have been switched. This process does not produce any secondary waste such as contaminated water, polluted air or any other products that have to be disposed of.

Jan 1, 2000

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015