Search Documents

By Ahmet Unal

Inexpensive and effective means of delivering courses to mining engineers who live at remote and scattered locations remains to be a challenging issue. Computer-based instructorless but interactive multimedia delivery is a good substitute to traditional short courses and one-way broadcasts. Such a system, enhanced with a wide area network, is an inexpensive alternative to two-way broadcasts and even to a traditional university. Course material can either be delivered on compact disks (CDs) or on-line from the host servers over the phone lines using a personal computer and a modem. Although technically not feasible using ordinary telephone service lines at the present time without further modification, advances in this field indicate that this up and coming medium may dominate the competition in the future. This paper investigates the present and the future of this technology and discusses the experiences gained in creating and disseminating a prototype multimedia CD which was created at the Rock Mechanics and Explosives Research Institute of the University of Missouri-Rolla to teach a portion of a course in Ground Control. The hardware and software used in creating the audio, 3-0 graphics, animation dips, video clips, and movies are listed. The structure of the program and the way how interactivity was achieved is explained in detail.

Jan 1, 1996

By Dimas Henrique Barros Andrade, Roberto Abreu Alencar

O algaraviz é uma parte importante do sistema de sopro de um Alto-Forno, utilizado para direcionar o sopro e combustíveis injetados para a ventaneira, por conseguinte o interior do forno. O algaraviz consiste em uma caraça metálica revestida de material refratário com resistência ao calor e uma camada de isolante térmico entre o refratário e a carcaça. Falhas em serviço de algaravizes costumam a gerar grandes danos materiais, financeiros e com grande risco à vida dos operadores, por isso o controle e inspeção da integridade estrutural e térmica dos algaravizes é de suma importância. A inspeção nos algaravizes é realizada a fim de se detectar precocemente pontos quentes que são indicativos de falhas estruturais no algaraviz. Portanto este artigo foi feito um modelo numérico de transferência de calor, a fim de se averiguar as condições do algaraviz, de forma a verificar se o algaraviz em condições normais de operação mantem as condições térmicas. O modelo revelou resultados satisfatórios de forma que em comparação com resultados de inspeções em peças em operação se obteve um erro de cerca de 8%.

Oct 1, 2019

Roof Bolts An expansion shell and plug Westinghouse roof bolting assembly made for use with threaded steel rods and large flat washers or steel channel employs a plug larger in diameter than those for trolley wire service. The notched plug helps prevent shell and plug from turning. The unit is shipped complete. Circle No. 1 Fan The Jeffrey Mfg. Co. Aerodyne Midget fan is a self contained blower or exhauster for auxiliary ventilation through tubing. Operating rating with 5 hp motor is 6.5 in. maximum static pressure, and 6200 cfm free delivery volume. Weight is 340 to 475 lb and it may be furnished in open or permissible form. Circle No. 2 Heavy-Density Initial installation in the Mesabi Range country of the Wilmot-Daniels heavy-density concentrating system was a 175 ton per hour plant at the [ ] Skubic Bros. Virginia, Minn., operation. This Wilmot Engineering Co. unit has a separatory vessel providing unidirectional medium flow and as the only moving part uses a standard drag-line conveyor for lifting sink out of the bath. Circle No. 3 Portable pH Meter A low priced battery-operated portable pH meter of utmost simplicity announced by the Photovolt Corp. uses only 3 ordinary radio batteries which give over 2000 hours of service. Accuracy of 0.03 pH is claimed by the manufacturer for the model 125, and AC power line supply is available. Circle No. 4

Jan 1, 1952

By A. H. Lang

THE recent production of important quantities of high-grade muscovite at the Purdy mine, near Eau Claire, Ontario, bas brought that district into prominence and bas added another strategic mineral to the list of Canadian products. The discoveries are thirteen miles west of Mattawa and about two miles north of the Trans-Canada highway and the Canadian Pacific railway. HISTORY Clear mica of low power factor is in considerable demand in Canada and in the United States for war purposes such as radio and telephone condensers, aircraft spark-plugs, radio tubes, and transformers. Some muscovite (white mica) bas been produced in North Carolina and New Hampshire, but the United States trade bas depended largely on importations of muscovite from India and of phlogopite (amber mica) from Madagascar. For many years Canada bas been a substantial producer of phlogopite, but was unable to compete extensively in the United States with importations from abroad. Canadian production of muscovite bas been negligible as no important deposits were known. Ever since the construction of the Canadian Pacific railway, attempts have been made from time to time to mine the pegmatite dykes in and near the Eau Claire area, but, although some feldspar has been mined, no appreciable muscovite was produced. Lace in 1941, J. Purdy and H. MacDonald discovered a dyke containing large crystals of high-grade muscovite from which they are reported to have sold $700 worth of mica. They recorded claims 35974 and 35975 in December, 1941, and claim 36095 in May, 1942.

Jan 1, 1943

By Kadri Dagdelen, Steven Hoerger

For gold mines, orebody uncertainty is one of the leading causes of differences between planned and actual production. Geostatistical conditional simulations create multiple equally probable orebody block model realizations which are conditional to the current drilling information and demonstrate the sampled grade distributions and spatial statistics. These simulated block models are key inputs for a stochastic evaluation to show the likely range of grades and cash flows to be delivered by a mine plan. The stochastic evaluation outputs can be used to compare different mine plans in terms of expected values and risks to planned grades, production, costs, Net Present Value (NPV) and other plan metrics. For the McLaughlin gold mine, risk profiles are demonstrated to show how different mine, cut-off and stockpile strategies can reduce risk and improve expected value. The strategies considered were effective in improving expected NPV and reducing or eliminating tonnage uncertainty, but the strategies had little impact on reducing the uncertainty of NPV’s or mill grades. The stochastic evaluation process is also used to compare the risk impact of orebody uncertainty against the risk of not achieving planned mining tonnages or vertical advance rates. Risks for plans created with and without stochastic mine plan optimization are also compared.

Feb 1, 2025

By G. R. Brunskill

The molybdenite flotation plant at Magma Copper Company, San Manuel concentrator has been in operation since 1956. In January of 1980 the plant was converted from a hydrogen peroxide - ferrocyanide process to the current sodium cyanide - sodium hydrosulfide process. This paper is an operational review of Magma Copper Company's molybdenite recovery circuit, column cell flotation experience and use of on- stream x-ray flourescence analysis.

Jan 1, 1985

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By Toshiaki Tsuru, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition behavior of Zn-Cr alloys from the methanol baths was investigated. In the methanol baths of low Cr3+ concentration, Cr (III) compound was incorporated in the deposits and no lusfrous Zn-Cr alloys was deposited. However, Cr was existed as metallic state in the deposits obtained from the baths of higher Cr3+ concentration. With an increase in water content in the baths, the chemical state of Cr in the deposits changed from metallic to trivalent state. Under the condition that metallic Cr can be electrodeposited, Zn deposition was significantly polarized to the potential of Cr deposition.INTRODUCTIONAn attention has been paid to Zn-Cr alloy plated steel sheet because of its excellent properties for body panels of automobile and electrical appliances [1]-[4]. This plating process can be operated using the sulfate solutions containing Cr3+ ion [1] - [6].In decorative single Cr plating, on the other hand, many attempts have been made to electroplate Cr from trivalent electrolytes, which is motived by environmental deficiencies of the presently used hexavalent process [7]. [8]. However, it has been reported that in the aqueous solutions the behavior of the electroreduction of 0 3+ is atypical due to the complicated nature of the chemistry and electrochemistry of cr3+ species [9]-[11]. Even in Zn-Cr alloy plating, it is difficult to codeposit metallic Cr with Zn in simple sulfate electrolytes [l]-[4], [12]. Therefore, it can be expected that the electrodeposition behaviors of Zn-Cr alloys as well as Cr are significantly changed when the electrodeposition is conducted in non-aqueous plating solutions.In this study, the electrodeposition of Zn-Cr alloy was conducted from methanol solutions to clarify the electroreduction mechanism of Cr3·-Cr0 in the alloy deposition process."

Jan 1, 2000

By J. E. Danoczi

ABSTRACT A diamond processing plant is being designed for the Star–Orion South diamond project in central Saskatchewan. Key to the plant is diamond liberation, which occurs in the comminution section and is the process of breaking up kimberlite rock as gently as possible to minimize diamond damage, particularly in larger, high-value diamonds. Kimberlite from the crater area of a volcanic pipe is generally softer than kimberlite from the diatreme zone. Softer kimberlite, comprising the majority of Star– Orion South deposits, can be readily broken up using abrasion and attrition by autogenous grinding mills, the preferred comminution method for minimizing diamond damage.

Jan 1, 2013

By Keros Cartwright

Distribution of temperature within the lithosphere can be significantly affected by the movement of ground water. Stallman (1960) presented the basic equation for the simultaneous transfer of heat and fluid in a porous medium and first used earth temperatures to determine aquifer permeability. Subsequently, studies of rock and soil temperatures were used to determine the flow of water through clay layers separating aquifers (Bredehoeft and Papadopulos, 1965; and Sorey, 1971), and to locate shallow aquifers (Cartwright, 1968; Birman, 1969). Cartwright (1968) showed that shallow aquifers maintain a nearly constant temperature throughout the year and that heat is exchanged between the aquifer and land surface. These temperature data also suggest that shallow aquifers hydrologically connected to surface-water systems have significantly greater effect on temperature distribution than aquifers in the deep artesian basins. Water wells developed in the shallow glacial and dolomite aquifers to depths of over 122 meters (400 feet) in northern and central Illinois produce water at temperatures very close to the mean annual air temperature. An analysis of the character of the rocks and soils suggests that the tem¬perature gradient should, and does, vary according to changes in thermal conductivity due to changes in lithology. This is because, under conditions of steady and uniform flow of heat from the earth's interior to the surface, a greater temperature gradient is required in poorly conductive rocks than in highly conductive rocks to transmit the same quantity of heat. Based on estimated values of thermal conduc-

Jan 1, 1972

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By Takayuki Sakai, Takefumi Takuma, Lee Roesner

"70-foot deep rectangular-shaped bulkheads were built with sheet piles as launching and receiving shafts for a pipe jacking operation for new underground waterlines in a densely populated section of Los Angeles, California. The Press-in Piling Method was specified to drive 95-foot long sheets (a record for the method) to form the bulkheads for the Los Angeles Department of Water and Power’s LA-29 (DWP) Connection Modification and Pipe Jacking. The piling was chosen because of its very low noise and practically vibration-free nature since the site is surrounded by houses, an apartment complex, and existing water lines. The out front areas of the bulkheads were grouted to let the TBM go through without major ground water leaks. Hydrophilic foam grout was also injected in addition to welding steel scab plates on the inside to seal them to achieve sufficient watertightness behind a few split interlocks. BACKGROUND This project was located in the Crescent Heights area of Los Angeles which is a few miles south of Beverly Hills. The project represents the completion of the last phase of the Stone Hollywood Trunk Line. This was an 8-mile long water trunk line that averaged 60 inches in diameter and was built to improve the reliability of the DWP’s major water system. This section of the project involved driving 2 deep shafts to allow for the installation of a 350-foot-long 72-inch steel casing using microtunneling construction. See Figure 1 for the shaft locations and the tunnel alignment. The challenge for the project was that this water line would have to pass beneath the Hollyhills buried box drain (15 feet high by 20 feet wide). Further complicating the construction was the soils beneath the drain. The DWP chose to drive the tunnel at a depth of approximately 65 feet to ensure that the ground conditions were uniform and suitable for the microtunneling equipment. There were two previous attempts to construct this work which failed because of poor ground conditions and very high water levels. This third attempt was critical because the DWP could not afford to have another failure due to the fallout with the residents being impacted by the project."

Jan 1, 2016

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By Margarete Kalin

Mine abandonment is associated with the securing of access to underground workings, shafts, raises and adits. Waste rock piles and tailings are generally contoured and revegetated. When the waste materials contain pyritic material seepages can often emerge long after the physical reclamation work has been carried out. Their extent and origin has to be delineated to facilitate remedial measures. The depth to which the seepages extended can be determined with an electromagnetic (EM) survey. This paper reports on the experience gained using a winter and a summer EM survey correlated with measurements of specific conductivity at the sediment water interface. Lake sediments and ponds which represent a homogenous background material are good media, where specific conductivity and electromagnetic conductivity can be correlated. The origin of the seepage within the recontoured mine site requires detailed site knowledge, as many anomalies in heterogenous materials such as represented by a mine site are evident.

Jan 1, 1994

By Francisco J. Sotillo

Using new ecological-natural-organic depressant for gangue and pyrite with antibacterial properties (control of acid mine drainage) with new improved xanthate collectors using rheology additive not chemical reacting with xanthate resulted in better sulfide flotation. Rougher-scavenger lead flotation tests were conducted increasing the concentrate grade from 7.07% Pb to 13.44% Pb, enhancing selectivity. Lead recovery increased from 64.08% to 79.38% and 80.40% using only the new depressant, and improved xanthate Z-11 and Z-4, respectively. The results demonstrated that the new depressant was selective and efficient, and the new improved xanthates stronger more selective collectors.

Feb 22, 2026

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By J. M. Seward, W. D. Dietzman, M. E. Hawkins

Analytical studies of formation waters are widely used by the petroleum industry as an aid in solving problems such as identifying intrusive waters , corrosion studies , treating injection water , and choosing open or closed water- injection systems . The solution of a problem is often simplified when reliable analyses of the waters under consideration have been made previously . Chemical analyses and electrical resistivity measurements are presented on 267 samples from 74 fields in south Arkansas , and 199 samples from 80 fields in north Louisiana .

Jul 1, 1960

By E. T. Dumble

Discussion of the paper of E. T. DUMBLE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. .1623 to 1638. E. L. DEGOLYER, Norman, Okla. (communIcatIon to the Secretary*).-Referring to Mr. Dumble&apos;s description of the stratigraphy of eastern Mexico, I should like to question the classification of the ?Papagallos? or ?Mendez? shales as being of Cretaceous age and the so-called overlapping of the Papagallos or Mendez shales by the Alazan shales; the classification of the San Felipe series as Cretaceous, and the correlation of the San Felipe series with the San Juan limestones. Mr. Durable apparently recognizes the continuity of the great shale formation by his use of the terms "Papagallos" and "Mendez," as equivalent and interchangeable, since the Papagallos Hills in the State of Nuevo Leon and Mendez Station in Northern Vera Cruz, localities at which the shale formation outcrops, and from which the formation names are taken, are approximately 250 miles apart and on opposite sides of the Tamaulipas barrier. The Papagallos shales (evidently referring here to the northern extension only) are said to be non-fossiliferous and no reason for .their Cretaceous classification is given, though in a previous article&apos; they are classified as Cretaceous because at their northernmost outcrop they "have the same relation toward the overlying Tertiary that the Escondido (Cretaceous) has through its whole extent." The Alazan fossil locality was found by me and the first collections from it were sent to Dr. Dall; about 17 species of marine invertebrates were recognized by him, the fauna noted as having a distinct Pacific tincture, and the age of the formation from which they cause pronounced lower Eocene. The outcrop of the shale formation has been traced continuously from this point by me and my assistants into the Panuco River region, where Eocene fossils are reported at a depth of 1,810 ft. in a well at Topila.2 From Topila the formation has been traced continuously north to the Padilla-Jiminez region in Central Tamaulipas. Lithologically, the formation is fairly constant and though I am only generally acquainted with it north of the Padilla-Jiminez region, until definite evidence of the Cretaceous age of the Papagallos shale in its type localities, or of an overlap, is available, it seems to me more logical to consider the shale formation a single stratigraphic unit of Eocene age.

Jan 12, 1915