Search Documents

By N. J. Grant, Hans Brunner

ThE materials used in this investigation were furnished by the Aluminum Co. of America and consisted of high-purity alurhinum (99.995 pct) and two aluminum-magnesium alloys containing approximately 2 and 5 pct Mg. The compositions of these alloys are listed in Table I. The materials were received as hot rolled 3/8-in. diam rods and were made from the same heats as the materials which were previously used in this laboratory.'j3 The rods were cold swaged to 1/4-in. diam by 1 in. long, and then had two parallel flats machined over the gage length 0.085 in. apart. The test bars were annealed for 10 min at 700° F, and strained 1 pct in tension at room temperature. They were electropolished (80 pct acetic acid; 20 pct perchloric acid, 70 pct concentration) at a temperature of 60°F at approximately 20 v. A grid, transverse or square, spaced 0.2 mm apart, was impressed by rolling a fine threaded screw (128 threads per in.) across the flat surfaces. The depth of the grooves was less than 5 p. For final annealing and grain size control the specimens were enclosed in aluminum foil and sealed in Vycor tubes. Annealing conditions varied from 1 hr at 700° F to 5 days at 1050° F, depending on the alloy content, to give for most of the specimens a final grain size of about 1 mm. This treatment was followed by electropol-ishing as described above. For the test series presented in Figs. 4 and 5 round specimens were used instead of flat ones, and fine machining marks served as marker lines instead of the impressed grid lines. Electropolishing was omitted. The major advantage is that the spacing of the machining marks is only about 1 u as compared to the 200 u of the impressed grid lines, permitting higher precision in strain measurements. Unfortunately the strain annealing necessary for grain size control also resulted in some preferred orientation of the grains. The preferred orientation of three arbitrary specimens was measured by X-ray diffraction methods and the averaged results are shown in Fig. 1. The possible effects of the preferred orientation on the test results will be discussed later. The testing temperatures were 410°, 515", 725", and 940° F, with one exception in the case of the 5.1 pct Mg alloy. Since the solubility limit of this alloy is 520°F, a test temperature of 545°F was cho-se sen instead of 515°F. The selection of the test temperature was based on two considerations: 1) at 900°F and above, extensive grain boundary migration made it more difficult to measure grain boundary sliding; 2) at 400°F and below, there was so little grain boundary sliding that it was again difficult to make precise measurements. The stress was chosen to give a creep rate of approximately 2.7 pct per hr in connection with Figs. 2

Jan 1, 1961

By Matheson and Miller

Does anyone have any definitive information on vibration limits for damage to well casings near blasting? Also, are people using self-imposed limits when approaching cased wells? I can only tell you what I have personally done with success. Often in new construction in hard rock, the well is drilled before the foundation is excavated and before the ditch for the water line is excavated. These both require drilling and blasting. Under these circumstances when blasting for the ditch for the waterline we will drill right up to within 10 inches (not feet) of the well casing. We drill line holes the width of the ditch, then about a foot from this, another row of trim holes then as we move away from the casing holes for 1 1/4 inch stick powder for about three rows then as we get further still, we can load with ANFO. I do not have vibration data for this but my experience has been that as long as you are not displacing the material into the casing that no damage is done. These typically are steel casings for residential water service.

Jan 1, 2010

Discussion of the paper of E. J. Hall and C. W. Drury, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1059 to 1066. A. M. SMOOT,* New York, N. Y. (communication to the Secretary +) :-The nails method is given in many text books on assaying as a standard method for gold or for gold and silver in ores. It appears to be taught in the laboratories of technical and scientific schools as a standard method, and to some extent it is used by assayers in actual practice, although the class of ores to which it may be applied is limited to those free from reducible metallic compounds, the metals of which would enter the lead button. The experiments of Messrs. Hall and Drury show the inaccuracy of this rnethod for silver, in heavy sulphides, but not so clearly the short-comings with regard to gold. It seems certain that low silver is caused by the solubility of silver in iron-alkali sulphide as compared with its solubility in molten lead; that is, silver is distributed between iron-alkali sulphide and metal in the charge in proportion to solubility at the particular temperature of the fusion. Lead is a fixed quantity in these assay charges, but iron-alkali sulphide increases with increased sulphur, so the more sulphur in the charge, the lower the silver results.

Jan 11, 1913

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By C. R. Kuzell

INTRODUCTION KNOWLEDGE of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is, frequently called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat is accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers,.etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any mcdern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases.

Jan 8, 1914

By Robert G. Benson, David M. Jones

The San Luis deposit of Costilla County, Colorado contains 11,021,000 tonnes (12,149,000 tons) of ore at 1.4 g/t (0.040 oz/st) gold in two mineable zones. Gold mineralization is associated with silicification and quartz-sericite-pyrite alteration localized in breccias along a low-angle "detachment" fault zone in Precambrian gneiss. Gangue minerals include chlorite, specularite, chalcopyrite, molybdenite, and fluorite. Mineralization is mid-Tertiary in age and may have an indirect genetic relation to the emplacement of felsic intrusions. Portions of the ore body are unconformably overlain by sedimentary rocks of the Tertiary Santa Fe Formation. The deposit formed during the early stages of extensional tectonism along the eastern edge of the present day Rio Grande rift.

Jan 1, 1990

By A. L. Holley

The occurrence of this gas, in quite appreciable quantities, has been observed for many years in its escape along the creeks of Western Pennsylvania, and more recently, in much larger quantities, from the oil wells in and near Venango County. Within about five years several gas wells have been struck, from which the gas has escaped continuously in prodigious quantities and at great pressure. During the last year a systematic attempt has been made to utilize the flow of gas from one of these wells, and results have been reached which were quite unexpected. This well, near Leechburg, Armstrong County, is about twenty miles northeast of Pittsburgh, on one of the side tributaries of the Alleghany River. It had been drilled in search of oil to a depth of 1250 feet in 1871, but none was found. A great flow of gas was developed, however, accompanied by a slight spray of salt water, and this has continued with little or no diminution to the present time. The gas in its escape has been discharged through a 5-inch pipe, and at a pressure of from 60 to 80 Ibs. per square inch, but no exact determinations, either of the pressure or quantity, have been made. The rolling mill of Messrs. Rogers & Burchfield is on the opposite side of the river, and it has been for some years devoted to the production of fine grades of sheet iron from charcoal pig metal, by puddling and in knobbling fires. The usual weekly product of the mill has been 30 tons of No. 30 tin plates, and 50 tons of No. 24 to 28 sheets. The well was bought by this firm for $1000, and the gas is led across the river, a distance of about 500 feet, through a 3-inch pipe. It is distributed through half-inch pipes, and at a pressure of about 45 Ibs. per square inch, to several of the furnaces, but a large fraction of the total flow of gas is still wasted at the well. No essential alteration in any of the furnaces has been found necessary in the use of the gas fuel, except to brick up the firebridge and to put in the gas and air pipes. The old grate used for coal is loosely covered with bricks and cinder, so that a slight percolation of air may take place through them. The gas is admitted through a half-inch pipe, and blows toward the fire-bridge through 18 or 20 one-eighth inch jets. The air is blown in at about 2 lbs.

By Akira Yazawa

Experimental results for the distribution ratios of various elements between the slag, matte and/or copper in the silica-saturated copper smelting system were summarized. The experiments were carried out under an oxidative smelting condition with S02 gas flow, and also a reductive smelting condition equilibrating with metallic copper or iron. To evaluate the results thermodynamically, the availability of one atom cation base expression for the constituent compounds is emphasized from both of theoretical and practical standpoints. Both of oxidic and sulfidic dissolutions in slag are postulated for some elements such as copper, nickel and lead., and the experimental results are reasonably explained thermo-dynamically. The results for the mutual solubility between matte and ferrite slag and the distribution of minor elements between liquid copper and ferrite slag are also discussed.

Jan 1, 1983

By James Fisher

THE copper mines of the Keweenaw Peninsula in northern Michigan have long been of interest in connection with deep earth-temperature measurements. The extraordinary low geothermal gradient of 1° F. in 223.7 ft. announced by Agassiz1 as a result of measurements dating from 1886, although later" stated as in error, served to focus attention on this region as one offering, because of the great depth of the mines, unusual opportunity along this line. Lane,3 Van Orstrand4 and others have made valuable contributions to this study. Fresh opportunities afforded by the constant deepening of the mines, improvements in the accuracy and reliability of temperature-measuring instruments together with increasing knowledge of the heat conductivities and specific heats of the rocks, led the Michigan College of Mining and Technology in cooperation with some of the mining companies to renew work on this problem. It is planned eventually to complete a survey which will make use of the favorable opportunities for deep rock-tempera-ture measurements presented in these mines. This survey should include the determination of a depth-temperature gradient in both conglomerate and amygdaloid mines, and also the variations in temperature at the same depth in different geological formations. The first problem has a direct bearing on the question of providing equipment for necessary ventilation with increased depth. The second may show that a relation exists between the natural rock temperature and the mineral content of the formation.

Jan 1, 1932

By Krzysztof Filek, Anindya Sinha, Bernard Nowak

Taking into account the possibilities of condensation of water vapour contained in air during its flow through a series of spot coolers as well as formation of eventual fog, a mathematical model of dynamic temperature, specific humidity and degree of fogging of cooled air in underground mining galleries with direct ventilation is developed. In the gallery, there situated various heat and moisture sources both of distributive and of concentrated types. The model is represented by three partial differential equations of first order. The cases of cooling with full as well as with partial air stream flowing through the gallery are distinguished. Owing to the fact that in practical designing, more important is the knowledge of the variation process of temperature, specific humidity and fogging of cooled mine air at steady state conditions, the model is modified to a set of three nonlinear ordinary differential equations. Based on the presented algorithm, the obtained set of ordinary differential equations is numerically solved which enables to: • specify the distribution of temperature, specific humidity, relative humidity and degree of fogging of cooled air in mining galleries; • determine the cooling powers of air coolers for their known locations; • indicate the locations of the coolers of known cooling powers. Exemplary calculations of temperature and relative humidity of cooled air are presented graphically in a number of diagrams.

Jan 1, 1997

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

By Lucia Kuizon

The Pinnacles Wilderness Contiguous Wilderness Study Area (WSA) (CA-040-303) is 30 miles south of Hollister, CA, in San Benito and Monterey Counties. It is composed of five parcels of public land totaling 5,838 acres adjacent to the Pinnacles National Monument. The U.S. Bureau of Land Management later reduced the size of the Recommended Suitable Area (RSA) to 2,200 acres. U.S: Bureau of Mines personnel examined the entire WSA in May 1984. The WSA is underlain by Tertiary sedimentary and Cretaceous plutonic rocks. Diatoms occur in interbedded tuff, shale, and sandstones in the northern part of the WSA, but outside the RSA. In 1984, there were no mines, prospects, mining claims, leases, or mineral resources in or within one mile of the study area. No energy minerals were identified; however, an oil well was drilled in 1951 in the northern part of the WSA, but outside the RSA; it was a dry hole.

Jan 1, 1985

By E. W. Newman

The Bureau of Mines, in cooperation with the U. S. Geological Survey, developed the property of the Tungsten Metals Corp. by surface trenching and diamond drilling from November 1940 to June 1941 and from August 1943 to December 1943. The purpose of the work was to determine possible reserves of tungsten in the downward extension and lateral eastern extension of three major tungsten-bearing quartz veins. The property is 50 miles south of Ely, White Pine County, Nev., in the Minerva Mining District. Tungsten ore was discovered in the district in 1915, and mining started in 1916. The tungsten ore bodies occur as shoots in quartz veins that occur along faults in limestone. With the exception of a small-scale leasing operation in 1932, the property was idle from 1919 until 1936, when Tungsten Metals Corp. was organized to acquire the mines. Production ceased in May 1945, and the mines were idle until leased in 1947. Development by the Bureau of Mines during 1940 and 1941 consisted of surface trenching, sampling, and diamond drilling 37 holes for a total of 6,959 feet. Subsequent drilling of eight holes, totaling 3,067 feet, in 1943 disclosed additional reserves. This report sets forth in considerable detail the exploration work completed by the Bureau and briefly describes the mining and milling methods employed. Diamond-drill halo logs and sample analyses are shown graphically in the illustrations that accompany the report.

Jan 1, 1950

By J. S. Gardner, J. J. Zaluski

I. INTRODUCTION West Virginia has a long history of coal production.1 The state at one time led the nation in total coal production, while at the same time coal from West Virginia constituted one quarter of total U.S. coal production.2 In more recent years, however, West Virginia’s level of coal production has been reduced in comparison to that of other states due to the high relative cost of producing coal in the state.3 Another blow to the producers of coal in West Virginia is the action known as Bragg v. Robertson.4 In 1998 various individual plaintiffs, as well as a conservation group known as the West Virginia Highlands Conservancy, filed a civil action under a provision of the Surface Mining Control and Reclamation Act of 1977, Pub. L. No. 95-87, §522, 91 Stat. 445 (codified at 30 U.S.C. §§1201-1328) ("SMCRA" or the "Act") that allows declaratory and injunctive relief against state and federal officials for non-compliance with the Act.5 The plaintiffs generally claimed that the Director of the West Virginia Department of Environmental Protection ("WVDEP") had exhibited a pattern of violating mandatory non-discretionary duties under SMCRA and the West Virginia state regulatory program.6 These non-discretionary duties involved many areas of regulation, including water quality standards, disturbance of wetlands, hydrologic reclamation plans, Approximate Original Contour ("AOC") requirements and AOC variances, post-mining land uses, contemporaneous reclamation, and as explained later, the "buffer zone rule."7 In addition to these claims against WVDEP, the plaintiffs also alleged that certain individual members of the Army Corps of Engineers (the "Corps") had failed to carry out statutory duties under the Clean Water Act (the "CWA") and the National Environmental Policy Act ("NEPA").8 Generally, the complaint stated that the Corps did not have statutory authority under the CWA to regulate valley fills created for the purpose of the disposal of waste material, i.e., the overburden associated with mountain top mining.9 Alternatively, the plaintiffs claimed that even if the Corps could regulate valley fills, the Corps violated NEPA by issuing nationwide permits without required analysis. Finally, the plaintiffs asserted that the issuance of a nationwide permit for surface mining valley fills is unlawful.10

Jan 1, 2001

By T Baumgartl, R Akesseh, M Edraki, B Usher, M Shaygan

With the continuing demand for industrialisation and urbanisation, the rate of mining and processing lower grade ores will also increase, producing large quantities of waste. As extreme weather events associated with global climatic changes are to be expected, the risk from mine tailings management will also increase (Edraki et al., 2014). In sulfide rich tailings, weathering within the critical zone controls the fate and distribution of the contaminants such as copper, zinc, and lead in the environment (Hayes et al., 2014). Tailings evolve geochemically and physically with time as they age under the influence of complex interacting factors. Understanding of the complex interactions between these controlling factors is important for predicting and mitigating the potential risks associated with sulfide tailings such as generation of acid mine drainage (Lindsay et al., 2015). Wetting and drying initiates weathering processes, influencing the hydrological, geochemical and geomechanical properties of the tailings. In semi-arid climates where evaporation exceeds precipitation, salts may precipitate within the pore system as well as on the tailings surface. These salts become the temporal sink of heavy metals until the next episodic rainfall (Nordstrom, 2011, Grover et al., 2016). Therefore, using kinetic and static test to describe the trajectory of these material evolutions without considering the complex interactions could potentially lead to erroneous prediction. In order to understand these relations, the effect of drying and wetting cycles on the hydrological, geochemical and geomechanical properties of ageing tailings was studied to draw conclusions for advanced tailings site rehabilitation and mine closureCITATION:Akesseh, R, Shaygan, M, Usher, B, Edraki, M and Baumgartl, T, 2018. Wetting and drying cycles as a means to determine the effect and consequences of tailings ageing, in Proceedings Life-of-Mine 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D. B. Williams

The end of the war in Europe and the Pacific failed to curb the upward trend of production in Venezuela,- which easily surpassed that of any previous year. The total production for 1945 amounted- to 323,369, 430 bbl., which was 26 per cent over the total for 1944, the previous peak in the history of the oil industry of the country. This increase was caused mainly by the greater demand for petroleum in the last stages of the war; the fact that the danger from enemy submarines had been overcome, which allowed all oil companies to use increased shipping facilities, and the fact that more materials were available for drilling operations. However, the materials supplied were by no means adequate and considerable credit is reflected on the Venezuelan petroleum industry for the increased production obtained by utilizing all available equipment to its fullest extent.

Jan 1, 1946

By W. A. Kracht

The McGill Bubble Size Analyzer, with the original image-capturing device (digital video camera), has a proven record for measuring bubble size distributions that are relatively narrow, such as in mechanical cells with frother. However, some problems arise when dealing with bubble size distributions characterized by a bi-modal shape and wide range of sizes such as found in some flotation columns. To measure wide bubble size distributions it is necessary to increase both the resolution to image the small bubbles and the viewing area to include the large bubbles. This can be done using a digital still camera: digital still cameras can have higher resolution than the digital video cameras currently used and with the proper lens the viewing area may be increased without resolution loss. The digital still camera approach was used to measure bubble size distributions in flotation columns at different operations in Chile. A comparison with typical bubble size distributions generated with mechanical cells is presented.

Jan 1, 2007

By W. F. Netezband, E. H. Crabtree

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By E. H. Crabtree, W. F. Netezband

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By R. Lovat, J. A. Hunter

"The design, development, and verification of the Lovat 7.6metre diameter full-face tunnel-boring machine is reviewed. Programmatic and technical challenges are outlined with a review of the specifications and the design to meet these requirements. Subsystem designs are presented for the waste material removal, ventilation, cutter head, structural support, advance technique, water removal, and interfaces with the Donkin-Morien Mine. The techniques used to verify that the design meets the requirements is by testing in the Lovat factory and in the field. Certification of the machine for use in a methane environment is discussed.IntroductionStudies have concluded that the average annual worldwide tunnel construction is 500 kilometres at an estimated average co st of $3,400 U.S . per linear metre. The total market value of the tunnelling industry is estimated as approximately $1.7 billion U.S. per annum. Of this, the current market for tunnelboring machine excavation is approximately $270 million U.S. per annum worldwide with a further potential of $250 million if more contractors are convinced that Tunnel-Boring Machines (TBM) are more suitable than conventional techniques. The worldwide civil tunnelling market has the potential to double each year in the next 5 to 15 years. Growth has been identified in the energy and mineral resources sectors of the economies of many nations and a significant volume of machine tunnelling studies and trials are presently underway for the extraction of coal, uranium , heavy oil or oil sand fuels, metallic and non-metallic industrial minerals and base metal or rare earth ores. Further tunnel projects for regional transportation, waterpower, irrigation , high density urban transportation, storm water sewers and water supply purposes are continually being implemented with new concepts like military security facilities and underground storage schemes being considered.Lo vat Tunnel Equipment of Rexdale, Ontario, the only Canadian manufacturer of TBMs was incorporated in 1973 to manufacture so ft ground tunnel-boring machines to satisfy this growing market demand. Lovat has produced an average of 5 machines per annum during the period 1972 - 1982 and has established an international reputation for competitive costs, quality of construction, after-sales service, and reliability. As of June 1982 Lovat TBM's have been used to tunnel over 240 km in projects throughout the world."

Jan 1, 1984