Search Documents

By P. W. Edwards

"This paper summarises many experiments conducted, and how in North American industry the use of aluminium in treatment and prevention has been adopted widely. The Pottery Insurance Co., Ltd., made it possible for me to investigate conditions in Canada and the U.S.A., and I thank them for permitting me to submit this short paper- an abstract of my report to them."

Jan 1, 1947

By Christopher Haycocks, Randolph Reed, Erik C. Westman

The industrial Source Complex (ISC3) model is the accepted standard used to predict emissions of particulate matter less tan 10µm in diameter (PM10) from industrial operations. This model, however, over-predicts PM10 emissions from surface mining operations, making permits harder to obtain. The over-prediction is likely due to the fact that the model applies emissions from mobile (dynamic) sources to stationary (static) areas. Utilizing a Gaussian dispersion equation, a Dynamic Component Program was created to correct the over-prediction of the model and results in a much more realistic modeling of actual conditions from mobile sources.

Jan 1, 2002

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By Richard A. McIvor

"All mine shaft conveyances in Canada and most of the United States that are supported by a single hoist rope or attachment point and used for transporting persons are required by regulation to be equipped with safety catches and mechanisms. These safety mechanisms, commonly called safety dogs, are designed to stop and hold a free falling conveyance, with a full personnel load, in the event of a hoist rope or attachment component failure. The conveyance’s safety mechanism must be tested under dynamic conditions before it is used to transport personnel. This paper will discuss free-fall testing and it’s results on conveyance free-fall tests performed in the test tower at INCO Limited, Sudbury, Ontario.Topics covered will be free-fall tests on various wood types such as B.C. fir, Karri wood and Trusjoist MacMillan Limited Parallamwood (PSL), comparison of deceleration rates versus free-fall velocity and the influence of safety dog tooth design on deceleration rates."

Jan 1, 1996

By R. Howard

"In projects involving resource development and plant optimization, the use of in-mine geophysics can deliver considerable benefit. The value proposition lies in using very high resolution downhole measurements to model process-plant outcomes. The calibration procedure used to convert in-situ physical properties into process engineering parameters is illustrated using two iron ore projects. Data correction was related either to orebody structure or mineral formation. The deliverable from this approach is a series of high-definition sections indicating the variability of ore delivered to a front-end separation plant and parameters for mine scheduling and stockpile design needed for maximum product yield.RÉSUMÉ Dans des projets de développement des ressources et d’optimisation de l’usine, l’utilisation de la géophysique minière peut engendrer des bénéfices considérables. La valeur de la proposition réside dans l’utilisation de diagraphies à très haute résolution afin de modéliser les résultats de l’usine de traitement. La procédure d’étalonnage utilisée pour convertir les propriétés physiques in situ en des paramètres d’ingénierie de procédés est illustrée en se basant sur deux projets de minerai de fer. La correction des données porte sur la structure de la masse minérale ou de la formation minérale. Les livrable attendus de cette approche sont une série de sections à haute définition, signalant la variabilité du minerai livré à une usine de séparation de première ligne, des paramètres pour l’échéancier de la mine et la conception des haldes requis pour une production optimale."

Jan 1, 2016

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By G Stanway, P Mahoney, C Griebel

The Mining Innovation – State of Play was initiated three years ago by VCI in partnership with the University of Western Australia. The ambition was to create a ‘think tank’ type platform to support industry discussion on how it is performing in terms of innovation at a strategic level, what needs to change in the industry ‘ecosystem’, and how businesses may more effectively develop their strategy and architecture to innovate for competitive advantage.The drivers for this ambition were straightforward. The industry recognises itself as being conservative with respect to innovation and it knows the business and community endowment dividend from getting better at innovation is large; however, much of the material that seeks to provide insight on innovation tends to be drawn from industries that do not have the same high capital, long life cycle and market uncertainty characteristics as that faced by mining. Material that does focus on mining innovation is orientated towards technical innovation, not innovation strategy. There exists a significant knowledge gap, and filling it is valuable to both mining businesses and communities.The 2014 Mining Innovation State of Play report (Stanway, Griebel and Mahoney, 2014), based on a survey of over 230 mining executives, uncovered a range of insights but left several questions unresolved. The people with the best perspective on these questions are CEOs. They can see the business issues with sufficient clarity and have the influence to shape both the industry and its organisations, as seen in Figure 1. Discussing these questions with the view to progressing our collective understanding was the primary reason this interview series was conducted.Unsurprisingly, interviewing 15 CEOs and Chairpersons from different industries and commodities, across the globe resulted in a broad range of views. The discussions were frank and often blunt in assessing the short comings in the industry and suggestions for improvement. This degree of candour is hugely valuable as a basis for improvement. In the end, four key areas emerged as a basis for improvement.CITATION:Stanway, G, Griebel, C and Mahoney, P, 2017. Mining Innovation State of PlayTM – iron ore insights, in Proceedings Iron Ore 2017, pp 439–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G N. Phillips

No new goldfields have been found in the Witwatersrand Basin for over 60 years, and one consequence of this is a long-term decline in gold production. Exploration throughout this period has been based on the placer model that infers alluvial transport of gold grains and then sedimentary sorting in the basin; however, there is no viable source for so much alluvial gold and no single sedimentary setting that hosts the gold.An alternative genetic model can now provide a quantified explanation for the source of the gold, and it does not rely on alluvial gold processes. The hydrothermal model can easily explain the source of the Witwatersrand gold as being derived from the background gold at parts per billion (ppb) level throughout the Kaapvaal craton of South Africa. This gold is involved in metamorphic processes, available for solution in metamorphic fluids, and hence may be transported whilst dissolved in fluid into the Witwatersrand Basin. The hydrothermal model warrants consideration as it can explain the source of gold, the large alteration halo in the goldfields, the mineralogy, and especially the gold-carbon association.Working on the premise that if one model (placer) is not giving the desired results (discovery of new goldfields), then it may be prudent to consider alternatives. Application of a hydrothermal model to guide exploration would place importance on large and small early structures in and around the Witwatersrand Basin; it would also emphasise the geochemical nature of potential host rocks (especially C and Fe) rather than their sedimentary origin.CITATION:Phillips, G N, 2013. Origin of Witwatersrand Gold - a viable source region and source process for gold, in Proceedings World Gold 2013 , pp 175-180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By Bianca Foggiatto, Marcos Bueno, Rajiv Chandramohan, Eddie McLean, Greg Lane

"With the increasing depletion of high-grade ore deposits, smarter mineral processing solutions are required to achieve sustainable and economic methods for mining and processing low-grade deposits. In order to make the treatment of low-grade deposits economically viable, large quantities of rock need to be mined and processed. The associated infrastructure costs (power, water supply, accommodation and support services, waste storage) result in a substantial penalty on the project, from both capital and operating cost perspectives. As a consequence, the challenge for the mining industry is to overcome the associated rise in energy and water consumption as well as increased project complexity when processing large amounts of low grade ore. Ore sorting technologies have been used for many years, predominantly on small projects, enabling the upgrade of marginal ores. Several sorting methods based on characteristics including specific gravity, radiometry, colour, particle size, grade and other detectable physical characteristics have been employed. The challenge for large low-grade ore bodies is to crush and sort at coarser rock size in order to minimise specific energy consumption in comminution and to reduce waste disposal costs. For large projects, the understanding of the economic impact of ore sorting is limited. The economic drivers include plant head grade improvement; sorting infrastructure capital, operating and maintenance costs; waste material handling and other environmental costs related to waste disposal. This paper analyses the economic impact of ore sorting in a large mineral processing operation. The focus of the analysis is to compare NPVs for a circuit including screening and ore sorting stages. A project for processing an Australian copper sulphide ore is considered as an example for this study."

Jan 1, 2014

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

By J. B. Morrow

WITH numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sam-pling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1935

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By E. D. Gálvez, L. A. Cisternas, A. López-Valdivieso, F. Lucay

"The floatability of molybdenite fines in saline solutions was investigated through microflotation studies using a modified Hallimond tube. In addition, the effect of pH and gypsum precipitation from calcium ions (Ca2+) and sulfate ions (SO4 2-) ions in saline water on the recovery of the molybdenite was analyzed. It was found that the floatability of molybdenite fines significantly increased with the ionic strength of the saline solutions and is independent of pH above 0.5 mol/L ionic strength. The high floatability of molybdenite in saline solutions is explained as being due to the low electrostatic repulsion between bubbles and the edges of molybdenite particles, which is exceeded by interactions due to van der Waals and hydrophobic forces. The precipitation of Ca2+ and SO4 2- ions as gypsum had a detrimental effect on the natural floatability of molybdenite because of gypsum crystal attachment on the faces of the molybdenite particles. This precipitation phenomenon may be initiated in copper–molybdenite flotation circuits that use recycled saline water, like seawater containing Ca2+ and SO4 2- ions.IntroductionWater availability is a significant factor in mining projects. Water, particularly fresh water from rivers and underground water, is becoming a scarce resource for mining operations and new projects. Under these circumstances, the use of water with high concentration of salts in flotation plants is becoming increasingly important (Cisternas and Moreno, 2014). The use of seawater has been studied as a sustainable solution for many mining companies in dry areas located near the sea. Notably, using seawater in mining operations is how mining companies in Chile have coped with the problem of water resources (Cisternas and Gálvez, 2014). In 1930, small plants in Chile used seawater to float chalcopyrite from high-copper-grade ores. In 1975, the results of tests in pilot plants for the flotation of copper minerals with seawater were reported. It was found that froth formation in seawater at pH 9.5 was suitable to make the rougher circuit work properly, even without frothers. The Cenizas mining group successfully floated chalcocite, bornite and chalcopyrite in the Las Luces plant in Taltal in Chile using seawater (Moreno et al., 2011). Minera Centinela (Antofagasta Minerals S.A. Chile) is currently processing porphyry copper ores using a seawater mixture consisting of 20 percent fresh seawater and 80 percent recycled water. Lower consumption of flotation reagents was reported in both seawater and salt water. In addition, studies performed with synthetic seawater showed that certain frothers increase the froth volume, whereas others decrease it. Additionally, the froth produced with seawater carries a high amount of gangue, and low-quality concentrates are obtained, requiring more cleaning stages."

Jan 1, 2015

By W. G. SWART

THE best estimate on reserves of iron ore in the Lake Superior district is that made, in 1920, by Mr. R. C. Allen, amounting to 2,947,225,000 tons of assured and probable ore. This includes direct- shipping or so-called merchantable ores, and those capable of beneficiation by demonstrated processes. De- ducting from this the 287,000,000 tons shipped since 1920, leaves a present reserve of approximately 2,500,- 000,000 tons, or; about 50 years' supply. The assured ore in this estimate is given as 1,560,500,000 tons, which checks Mr. Lake's estimate of 1,528,948,000 tons, or about 30 years' supply. This is not a long time in the life of the steel industry, and it can be readily appreciated that the matter is important enough to war- rant the attention it is beginning to receive. The first question that engages our attention is, What is merchantable ore? In 1902 the average of all Mesabi shipments was 56.07 per cent iron and 4.35 per cent silica. Twenty-five years later it had dropped to 51.99 per cent iron, with silica up to 7.92 per cent. It has remained around these figures for' ten or twelve years and, except for a probable rise in silica, can stay there for an indefinite period. Most of these figures I am giving cover the Mesabi Range. Including the other ranges does not change the figures greatly, and the Mesabi Range commands the situation, since it produces about 65 per cent of the total annual tonnage and, according to Mr. Allen, contains 81 per cent of the assured reserves, 50 per cent of the probable reserves, and 66 per cent of both the assured and the probable reserves.

Jan 1, 1926