Search Documents

By Filippo Vallianatos, Michael Verigakis, Vasili Saltas, Kosta Kaklis, Stelio Mavrigiannakis, Zach Agioutantis

"Development of failure in brittle materials is associated with microcracks, which release energy in the form of elastic waves called acoustic emissions. This paper presents results from acoustic emission measurements obtained during three-point bending tests on Nestos marble under laboratory conditions. Acoustic emission activity was monitored using piezoelectric acoustic emission sensors, and the potential for accurate prediction of rock damage based on acoustic emission data was investigated. Damage localization determined based on acoustic emissions evident in the critically stressed region in the form of scattered events or stresses below and close to the strength of the material.IntroductionNon-destructive testing (NDT) has gained popularity in recent years due to commonly available sensors, devices and software tools. Although the majority of such testing still occurs under laboratory conditions, the ultimate goal is a direct field application, especially in the case of underground mining. NDT, if properly applied, may be used to directly provide material property values and characteristics that can be used to determine rock mass or soil mass behavior, with a direct impact to mine design (Iannacchione et al., 2003).AE is generally defined as the high-frequency transient elastic waves originating from the sudden release of energy at localized points within a loaded material (Nomikos et al., 2010). The field of Acoustic Emissions (AE) due to compressive, tensile or other types of loads is a promising research area due to its wide application. The accurate identification of failure precursors stemming from AE is still an open research topic (Lei et al., 2004).Rock is a typically inhomogeneous and anisotropic material that contains several natural defects with various scales such as grain boundaries, microcracks, pores and joint inclusions (Jing, 2003; Read, 2004). Damage induced by microcracks is an essential mechanism in many brittle rocks subjected to stresses. An applied stress induces microcrack growth and damage is distributed uniformly throughout the sample. Finally, the microcracks coalesce and the damage is localized to a shear band, leading to strain softening and macro-scoping failure (Dragon et al, 2000)."

Jan 1, 2015

By Paulinelli Santos Rocha

A frota de equipamentos retro escavadeiras 345 CAT é responsável pela infraestrutura das minas do complexo Mariana, e este Projeto foi desenvolvido devido a baixa confiabilidade que estes equipamentos estavam apresentando. Foi desenvolvido um Projeto de seis sigma para aumentar a confiabilidade do equipamento que é medido pelo indicador MTBF, calculado pela fórmula: horas trabalhadas/ocorrências corretivas. O trabalho foi desenvolvido através de ferramentas de análise e solução de problemas no período de outubro/2012 a agosto/2013. O MTBF médio da frota era 29,39 horas sendo o benchmark de 47 horas. Foi utilizado o método da lacuna para estabelecimento da meta. Após definido a meta foi utilizada ferramentas de priorização dos focos mais relevantes. Para os focos encontrados foram utilizados análise de variabilidade e cartas de proporção, sendo cada causa classificada e priorizada, definido as ações e implantadas. Foi acompanhado o indicador de MTBF e implantados controles de rotina e padronização com o intuito de alcançar o resultado. Por fim, a meta estabelecida foi alcançada, chegando ao MTBF médio da frota de 42,50 horas.

Aug 8, 2018

Trans. No. Place Date Vol. Page 1. Wilkes-Barre Pa......May.71 1 3 2. Bethlehem, Pa.........Aug., '71 I 10 3. Troy, N.Y............Nov..: 71 1 13 4. Philadelphia, Pa........Feb., 72.. 1 17 5. New York. N. Y.*......May, '72.. 1 20 6. Pittsburgh. Pa.........Oct..' 72.. 1 25 7. Boston, Mesa..........Feb., '73.. 1 28 8. Philadelhia, Pa.*......May, '73.. 2 3 9. Easton, is............Oct..' 73.. 2 7 10. New York, N. Y.......Feb..' 74 . . 2 11 11. St. Louie. Mo.*........May,' 74 . . 3 3 12. Hazleton, Pa...........Oct., '74.. 3 8 13. New Haven Conn......Feb., '75.. 3 15 14. Dover,N.J.*..........May, 75.. 4 3 15. Cleveland,O...........Oct. 75. 4 0 16. Washington D. C......Feb.'' 76.: 4 18 17. philadelphia, Pa.......June,: 76.. 5 3 18. Philadelphia Pa........Oct 76.. 5 19 19. New York, N. Y.......Feb: '77.. 5 27 20. Wilkes-Barre. Pa.*.....Mag :77.. 0 3 21. Amenia N. Y..........Oct. 77.. 6 10 22. Philadeiphia Pa........Feb.;' 78. . 6 18 23. Chattanooga' Term.*. . . May' 78. . 7 3 24. Lake George: N. Y....: Oct. 78. . 7 103 25. Baltimore, Md.*.......Feb:' 79.. 7 217 26. ~ittsburgi, Pa.........~a;' 79.. 6 3 27. Montreal, Canada......~ept.;' 79.. 8 121 28. New York, N. Y.*......Feb., '80.. 8 275 29. Lake Superior, Mich....Aug., '80. . 9 1 30. Philadelphia, Pa.*......Feb., '81. 9 275 31. Staunton, Va..........May, '81. .10 1 32. Harrisburg, Pa.........Oct.. '81..10 119 33. Washington, I). C.*....Feb., '82. . 10 226 34. Denver. Colo..........Aug.. '82. . ll 1 35. Boston. Mass.*.........Feb.. '83..11 217 38. Roanoke, Va...........June, '83.. 12 3 37. Troy, N. Y...........Oct.. '83. .12 175 38. Cincinnati. O.*.... Feb, '84..12 4 39. Chicago Ill............May, '84. . 13 1 40. philadelphia, Pa........Sept., '84. . 13 285 41. New York, N. Y.*......Feb., '85. . 13 586 42. Chattanooga, Tenn.....May, '85..14 1 43. Halifax, N. S..........Sept., '85.. 14 307 44. Pittsburgh, Pa.*........Feb.. '86 . . 14 587 45. Bethlehem. Pa.........May, '86 .. 15 Ixiii. 46. St. Louis, Mo..........Oct, 86.. 15 Ixx. 47. Scranton, Pa.*.........Feb.', '87. . 15 lxxvi 48. Utah and Montana.....July '87.. 16 xvii. 49. Duluth, Minn...........July' '87. -16 xxiv. 50. Boston. Mass.*.........Feb.: '88. . 16 xxviii. 51. Birmingham, Ala.......May, '88. .17 xix. 52. Buffalo N. Y..........Oct. '88.. 17 xxiv. 53. New york, N.Y........feb.' ;89 . . 17 xxxi. 54. Colorado..............June' 89 . . 18 xvii. 55. Ottawa, Canada........Oct., 89. . 18 xxiv. 56. Washington, I). C.*. . . Feb. 90. .18 xxx. 57. New York, N. Y........sept:, '93. .19 vii. 58. New York, N. Y.*......Feb. '91. . 19 xxv. 59. Cleveland, O.......... June, :91 . .a xvi. 60. Glen Summit, Pa.......Oct, 111. . 20 lxi. 61. Baltimore, Md.*.......Feb.: '92. .21 xix. 62. Plattsburg, N. Y.......June, '02. . 21 xxxiii. 03. Reading. Pa...........Oct., :92. .21 xliv. 64. Montreal. Canada*.....Feb. 93..21 65. Chicago, Ill............aug.: '93..22 XI. 66. Virginia Reach. Va.*. ...Feb., '04. .24 xwl. 67. Bridgeport Coon.......Oct., '94..24 xxx?. 08. Florida ...'............Mar., '95. .25 xix 69 Atlanta. Ga......... Oct 95. 25 xi 70. Pittsburgh. Pa.*........Feb., '96.. 26 xvii. Trans. No. Place Date Vol. Page 71. Colorado..............Sept. '96. .26 xxix. 72. Chicago, Ill............Feb.. "97.. 27 xvii. 73. Lake Superior..........July '97. .27 xxx. 74. Atlantic City, N. J.*. ..Feb.: :98. .28 xvii. 75. Buffalo N. Y..........Oct. 08. .28 XXXVI. 76. New York,N. Y.*......Feb.: '99. .29 xvii. 77. California.............Sept., ;99. . 29 xlix. 78. Washington, D. C.*.....Feb., 00. .30 xix. 79. Canada...............Aug.. '00. .30 xlv. 80. Richmond. Va.*........Feb.. '01. . 31 xix. 81. Mexico................Nov..'01.. 32 cxviii. 82. Philadelphia Pa. $......May, :02. . 33 xxxv. 83. New Haven, Conn......Oct.. 02.. 33 xlvii. 84. Albany N. Y.*........Feb '03. .34 xxiii. 85. New York, N. Y........Oct.': '03. .34 xi. 86. Atlantic City. N. J.*....Feb., '04. .35 XXIII. 87. Lake Superior..........Sept.'04. .35 dii. 88. Washington. D. C......May' '05. .36 xlii. 89. British Columbia.......July, '05. . 36 90. Bethlehem. Pa.........Feb. '06. .37 xli. 91. London, England.......July: '06. .37 xlviii. 92. New York, N. Y........April, '07. . 38 lii. 93. Toronto, Canada.......July. '07. .38 lix. 94. New York, N. Y........Feb., :08. .39 xli. 95. Chattanooga, Tenn.....Oct.. 08..39 xlviii. 06. New Haven Conn......Feb. '09. .40 xli. 97. Spokane,Wash.........Sept:.'09. .40 xlviii. 98. Pittsburgh, Pa.........Mar.,'10. .41 xxxviii. 99. Canal Zone............Nov.,'10. .41 dv. 100. Wilkes-Barre, Pa.......June. ' 11. . 42 xxxiv. 101. San Francisco, Cal......Oct.. '11..42 xliv. 102. New York. N. Y.*......Feb 12. .43 Ixxvii. 103. Cleveland, Ohio........0ct;' '12.. 44 wii. 104. New York, N. Y.*......Feb.. '13. .45 xv. 105. Butte, Mont...........Aug., '13. .46 ?' 108. New York, N. Y........Oct., 13..47 vii 107. New York. N. Y.*......Feb.. '14..48 xv. 108 Salt Lake City. Otah Aug. :l. 49 5: 109. Pittsburgh, Pa.........Oct., 14. .50 vii. 110. New York, N. Y.*......Feb., '15. .51 xvi. 111. San Francisco, Cal......Sept., '15. .52 xii. 112. New York,N. Y.*......Feb., '16..54 xvi. 1 Arizona...............Sept.,'l6. .55 VII 114. New York, N. Y.*......Feb., '17: .56 vii. 115. St. Louis, Mo..........Oct.. '17..57 vii. 116. NewYork,N. Y.*......Feb.. '18..59 xvii 117. Colorado.....:........Sept.,'18. .60 vii. 118. Milwaukee, Wis........Oct.. '18. .60 x:!: 119. NewYork,N. Y.*......Feb., '19..61 xi. 120. Chicago...............Sept.,' l9.. 62 VII. 121. New York, N. T.*......Feb., '20..63 ix. 122. Lake Superior District. .Aug., '20.. 66 ix. 123. New York, N. Y.*......Feb., '21. .66 xiii. 124. Wilkes-Barre, Pa...... Sept.. : 21.. 66 xix. 125. New York, N. Y.*......Feb., 22. .67 ix. 126. San Francisco. Cal......Sept.,:22. .68 xxix. 127. New York, N.Y.*.....Feb., 23. .69 xxix 128. Canada...............Aug., '23. .69 xxxv! 128.129. New York, N. Y.*......Feb., ;24. .70 xxxi. 130. Birmingham, Ala.......Oct. 24. .71 xxxiii 131. NewYork.N Y.*......Feb.: '25.. 71 xxxviii. 132. 131.Salt Lake City, Utah .. .Sept., '25. .73 xvi 133. New York, N. Y.*......Feb., '26. .73 xxii. 134. Pittsburgh Pa ....... Oct.. '26. .74 xv. 135. New York,' N. Y.*............Feb., '27. .75 x::: 135.136. NewYork,N. Y.*......Feb., '28..76 104 137 NewYork.N. Y.*......Feb., '29. .291 116 138.San FranciscoYork,N.Y. Cal..........Oct. 29..308 406 139. New York, N. Y.*...Feb., '30..30H 1321

Jan 1, 1930

By Jacob Mathis, Mark Bradford, Alston Noronha, R. M. True

In June 2022, Louisville MSD completed a 6.5-km (4.0-mi), 6.1-m (20-ft.) diameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. For large diameter shaft and tunnel construction, drill-and-blast operations among other methodologies were used in close proximity to federal, commercial, and residential properties with no impact to stakeholder infrastructure. s one of the rst maor tunneling proects in Louisvilles metropolitan area, this paper explores Black & Veatchs rigorous geotechnical instrumentation monitoring program that provided uality assurance for local stakeholders and afrmed innovative tunneling solutions can be successfully executed in an urban setting.

Jun 23, 2024

By W. D. Forgeng, P. F. Wieser

MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.

Jan 1, 1964

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

By G. Jandieri

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling industrial waste. The methodology is based on the break-even control mechanism, but at the same time provides for the introduction of new evaluation criteria such as the threshold of conditionality and the degree of ore substitution. Based on an improved analysis, it becomes possible to more precisely predict recycling efficiency. A more refined determination of the lower limit of concentration of recoverable metals, at which technogenic waste can be assigned the status of secondary raw materials and processed profitably, leads to a significant expansion of the secondary raw material base suitable for recycling. The potential for recycling manganese-containing dust from the production of ferrosilicomanganese, dehydrated sludge from the hydro separation of slags, and cake from the production of electrolytic manganese dioxide at the Chiatura mining enterprise is used as an example. It is shown that with a threshold of –24% Mn content, the highest recycling efficiency can be achieved by the production of low-phosphorus manganese slag and conversion to ferrosilicomanganese using the above waste to replace 40-60% grade III and IV manganese concentrates in the feed.

Jan 26, 2023

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011

By F. Nava-Alonso, E. Pérez-García, A. Uribe-Salas, J. C. Fuentes-Aceituno, A. A. González-Ibarra, E. N. Castillo-Ventureño

"Precious metals cannot easily be recovered from tellurides by the standard cyanidation process. This work assesses the cyanidation of synthetic samples of precious metals tellurides and explores some alternatives for the leaching of these species (i.e. cyanidation in presence of lead nitrate and thiosulfate leaching). For this purpose, three chemical systems were studied: (1) cyanidation of silver telluride and the effect of lead (II) nitrate addition, (2) cyanidation at high alkalinity and high cyanide concentration of a gold-gold telluride sample containing tellurium and tellurium dioxide, and (3) thiosulfate leaching of silver telluride employing cupric sulfate as oxidant and EDTA as complexing agent for copper. Results showed that standard cyanidation dissolves 10.5% of silver from silver telluride in six hours, while with the addition of 100 mg/L lead increased the silver dissolution up to 100% in the same time. The standard cyanidation of the gold-gold telluride sample dissolves only metallic gold in six hours, while when cyanide concentration and pH were increased, gold and gold telluride were simultaneously dissolved. Finally, thiosulfate leaching dissolves 43.1% of silver from silver telluride in six hours.INTRODUCTION Precious metals tellurides are classified as refractory ores due to the difficulties associated with processing them by the standard cyanidation method. The increasing presence of gold/silver tellurides in some deposits around the world, specifically in Sonora, Mexico, requires new approaches to the cyanidation process, or the development of new leaching techniques. Treatments have been proposed for the recovery of gold and silver from their tellurides, including roasting, preoxidation, cyanidation with lead nitrate, and the use of leaching agents other than cyanide (Zhang, et al., 2010; Ellis and Deschenes, 2016). This work presents preliminary results of three options to recover precious metals from pure tellurides: the cyanidation of gold telluride at high cyanide concentration and high alkalinity, the addition of lead nitrate to the standard cyanidation process, and the use of sodium thiosulfate as leaching reagent."

Jan 1, 2017

By A. A. Wallach

During the early design stages of the San Manuel Concentrator, numerous questions were raised concerning the required slope for tailings pipelines. The tailings disposal area which had been selected was so situated, that an average down-slope of 5% existed. A gravity tailings disposal system was to be designed and it was necessary to determine the optimum pipeline slope for design purposes. This information was also necessary to determine the life of the available disposal areas before tailings pumping would be required. At approximately the same time as this problem arose, it was reported that a concentrator in the southwest was having considerable operational difficulties due to periodic plugging of tailings lines. These factors combined made it seem desirable to conduct some sort of test work which might give information concerning the flow characteristics of the tailings to be produced, from the San Manuel Concentrator. It was felt that the maximum information could be obtained if a tailings line could be erected which would allow for varying slopes, varying heads and accurate measurement of pulp velocity. A five-foot Denver Agitator was installed on a bank overlooking a cut for a rail- road track. Approximately 160 feet for new &-inch pipeline with victaulic connections was installed on low trestles along the track, with provisions made for varying the slope of the line by use of accurately constructed sets of shims, A valve discharge was installed on the tank so agitated pulp could be run into a standpipe at controlled volumes. This standpipe was 10 inches in diameter and approximately 5 feet high. A 4-inch nipple welded into the side of the standpipe approximately one inch from the bottom was connected to the 4-inch pipeline. At the discharge end of the 4-inch pipeline a launder arrangement was so constructed that the entire discharge could run into a pump sump or into 50-gallon measuring vessels. In normal operation the flow was from the agitator to the standpipe through the pipeline into the pump sump and from there pumped back to the agitator tank.

Jan 1, 1958

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Apr 1, 2005

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By Luis Artola

El presente texto señala la estrategia de implementación, la estructura y los principales entregables para lograr la integración de tres aspectos de la gestión de la organización: la calidad, la seguridad, salud y la protección del medio ambiente. Para ello, se utiliza el sistema de calidad ISO 9001 como modelo de mejora continua que integra a los otros dos sistemas de gestión (de seguridad/salud y medio ambiente) de forma que enlaza con el modelo de gestión de proyectos (del PMI) para la realización de los trabajos.

Apr 1, 2015

By Albert Neumann, Franz-Werner Gerressen, Giancarlo Santarelli

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. In addition they are also quite often used as deep groundwater barriers, named Cut-Off-Walls (COW). Due to the requirements of each particular job site, e.g. the need for carrying high loads or as seepage barriers, there is an increasing industry demand for efficiently cutting into rock. Besides the removal of boulders, cutting through rock, is always the most difficult part of the excavation process of a diaphragm wall or COW.There are a number of influencing factors which have an impact on the rock cutting performance. Besides the influence of the rock characteristics itself, which is not always the same, there are other factors related to equipment, tooling as well as the operating staff. In addition to RQD, the most commonly available rock property found in geotechnical reports is the Unconfined Compressive Strength (UCS) value. There are however some other related properties, such as weathering, bedding, inclination, abrasiveness, etc.,which can have a major impact on the achievable cutting performance. This paper will discuss the various parameters, and how they can be considered for performance estimation. Based on experiences gained on over 100 projects, a performance estimation chart was developed to allow for a better approach to these kinds of projects. This paper also explains the general installation process in as well as some specific features related to specific site conditions. In addition, some job site references will give more detailed information about such type of site conditions and how to deal with them.Keywords: Diaphragm wall, Cut-Off-Wall, Trench Cutter, RockINTRODUCTIONDiaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits, shafts, permanent foundation walls and load bearing elements.It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions.In addition diaphragm walls can also be used as deep groundwater barriers (Cut-Off-Walls). This market has demonstrated that the demand for these types of walls is reaching ever more difficult soil conditions and greater depths which are surpassing the current industry standards. The trench cutter is the most important tool for performing this type of work."

Jan 1, 2016

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010