Search Documents

By Strathmore R. B. Cooke, Thomas E. Ban

MUCH experimental work has been performed on the mechanism of agglomeration and pelletizing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiöld and Ilmoni1 much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the microstructures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was. added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.2 Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl methacrylate monomer.3 The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45°C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.4 Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wüstite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1952

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By Bruce H. Mason

Lightweight aggregates are classified as those minerals, natural rock materials, rock-like products, and byproducts of manufacturing processes that are used as bulk fillers in lightweight structural concrete, concrete building blocks, precast structural units, road surfacing materials, plaster aggregates, and insulating fill. Other uses include architectural wall covers, suspended ceilings, soil conditioners, and other agricultural uses (Mason, 1989). One unusual agricultural use recently reported was for bedding on a crocodile farm on the south coast of Natal. It seems that female crocodiles became upset because there was no vermiculite in which to lay their eggs due to the late arrival of a consignment of vermiculite. The vermiculite was being used as a substitute for river sand to nest crocodile eggs (Griffiths, 1989). The various lightweight aggregate materials may be classified into four groups as follows: 1. Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials, such as pumice, scoria, tuff, breccia, and volcanic cinders. 2. Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing shale, clay, or slate in rotary kilns or on traveling grate sintering machines. 3. Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. This group of lightweight materials, with the exception of slag, has become less significant and will not be discussed in this chapter. Other lightweight aggregates are beginning to appear in the marketplace. Some are the result of manufacturing processes on industrial byproducts and/or waste products, such as fly ash and incinerator residue (Bigner, 1992). 4. Manufactured Insulating Ultralightweight Aggregates-pre- pared by pyroprocessing ground vermiculite, perlite, and diatomite. The application of diatomite in brick and in extruded and aggregate forms has declined in recent years (Kadey, 1983) and will not be considered in this chapter. Lightweight aggregates for structural concrete and concrete masonry units, according to the American Society for Testing and Materials (1986) consist of "aggregates of low density used to produce lightweight concrete, including: pumice, scoria, volcanic cinders, tuff and diatomite; expanded shale, clay, slate, perlite, vermiculite or slag; and end products of coal or coal combustion" (Mason, 1989). Lightweight aggregates are distinguished from other mineral aggregate materials by their lighter unit weights-1 281 to 1 602 kg/m3 or less for loosely packed lightweight aggregates-as com- pared to 2 002 kg/m3 or more for crushed stone, sand, gravel, air-cooled slag, and other common mineral aggregates. The specific gravities of these lightweight aggregates are also used to classify them for use in concrete; they range from the extremely light materials, used for insulative and non-structural concrete to expanded shale, clay, slate, and slags used for structural concrete. Vermiculite and perlite are sometimes referred to as super light- weights. Insulating concrete (non-load bearing) weighing as little as 240 kg/m3 can be made with these aggregates. Natural aggregates such as pumice, pumicite, and scoria are normally made into concrete weighing about 400 to 480 kg/m3. Expanded shale, clay, and slate produced in a rotary kiln make structural concrete ranging from 1 201 to 1 842 kg/m3. Expanded shale and clay produced by sintering make concrete that ranges from 1 442 to 1 922 kg/m3. Air-cooled slag produces concrete ranging from 2 162 to 2 403 kg/m3. The low density lightweight aggregates are used primarily for insulating purposes. They have relatively low compressive strength. The middle density aggregates are used for insulation and for fill. Those at the upper end develop excellent compressive strength and are used in many structural applications (Anon., 1971). In recent years, the production of lightweight aggregates in the United States for all uses (including insulation and construction materials) has averaged about 19 Mtpy (Table 1). The production and consumption of lightweight aggregate is closely tied to the fortunes of the construction industry and the need to construct energy efficient buildings. Recent years have seen the production of lightweight aggregate approach the levels of the early 1970s. The period of 1979 to 1981 was a low point in production levels. The low levels of production were caused by significantly higher plant energy costs due to the large amounts of fuel and energy used in the production of most types of lightweight aggregate. Lower levels of construction activity also affect production levels. This chapter focuses on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and on both the production and use of manufactured structural light- weight aggregates. Some additional comments are made on byproduct materials. Separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders are elsewhere in the volume. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials.

Jan 1, 1994

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990

By T. H. Koenning

Spontaneous combustion in western U.S. coal mines has been recognized as a serious problem which requires unique solutions. Methods have been developed for longwall mining which rely on the existence of an oxygen-deficient atmosphere in the gob for control of the spontaneous combustion hazard rather than the use of bleeder systems. Monitoring of the gob atmosphere is required to protect against the possibility of an explosion and to detect spontaneous heatings. Data from an example mine employing such a system is included to illustrate normal gob gas trends and is compared to abnormal trends which resulted from and were indicative of a fire. Under normal circumstances the oxygen (O2) and carbon monoxide (CO) concentrations decline rapidly as the longwall face retreats. Samples taken from a leaking seal in the example mine prior to a spontaneous heating showed virtually no oxygen depletion, contained erratic CO concentrations, and indicated the existence of hydrogen, a fire indicator. The appearance of an abnormal trend in the gob atmosphere can be used as an early warning of spontaneous heatings.

Jan 1, 1992

By J. M. Gomes

The Bureau of Mines, as part of an effort to maximize minerals and metals recovery from domestic resources, has investigated the feasibility of recovering heavy minerals as byproducts from sand and gravel, placer gold, and industrial mineral operations in northern California. Sand samples from about 50 locations were treated by gravity separation to yield heavy-mineral concentrates (black sands). Mineral compositions of the concentrates were determined by chemical analysis and mineralogical examination. Individual zircon, ilmenite, magnetite, platinum-group metals, thoria, and silica products were prepared from heavy-mineral concentrates by selective separation using low-and high-intensity magnetic, high-tension, and flotation equipment.

Jan 1, 1979

By Michael J. Pratko

The bulk handling industries have long been plagued with problems in their attempt to obtain one of their major goals - the maximum efficiency for which a bulk handling flow system was designed. Mentor Dynamics Ltd. is an international firm with offices in Canada, Japan, and the United States. Mentor Dynamics Ltd. is in the business of solving the "why not" of a system and engineers the solution for the problem. Studies of the varied difficulties encountered with bulk flow systems indicate that 90% of all flow problems fall into one or more of the following categories: abrasion, impact, sticking, and/or inadequate design. These problems can occur with a myriad of bulk solids: coal, gypsum, aragonite, phosphate, fly ash, ore. Solutions to the problems are as varied as the problems. The proper lining material, ceramic, urethane, rubber, and/ or ultra high molecular weight polyethylene, must be coupled with the correct fastening system, annular ring and 'F' cap, weld washer, button head fastener, weld studs and/or nuts and bolts.

Jan 1, 1982

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

By Zong-Xian Zhang

In sublevel caving mines, serious eyebrow break usually gives rise to lower ore recovery, higher dilution, and worse safety for the people working in the field. For example, chargers must go near the caving region and stand under the damaged eyebrow where a hanging stone may suddenly fall down or rock fragments may quickly roll down.

Jan 1, 2011

By R. C. Urquhart, D. D. Howat, R. I. L. Guthrie

Heat losses from ladles during teeming by R. C. URQUHART, M.Eng. (McGiII), Ph.D. (Visitor). R. I. L. GUTHRIE, B.Sc. (Eng.) (London), A.R.S.M., Ph.D., D.I.C. (Visitor), and D. D. HOWAT, B.Sc. (Glas.), Ph.D. (Fellow) In an investigation of the loss of temperature by liquid steel during a teeming operation, a numerical technique was used to calculate the heat flows and the rate of temperature drop over the entire teeming operation. The calculations show that, before teeming, approximately 50 per cent of the heat loss is into the ladle wall at the level of the metal. As teeming progresses, the amount of heat lost by radiation to the wall above the metalline increases. The effect of variables, such as initial metal temperature, the preheat of the ladle and ladle cover, and delays, on the rate of temperature loss by the metal were determined.

Jan 11, 1973

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or hear it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By C. W. Davis, R. S. Dean

The purification of iron ores by means of hand magnets dates back more than 100 years. The first record in the United States Patent Office of a machine for the magnetic separation of ores shows that on Feb. 20, 1849, U.S. Patent 6121 was issued to Ransom Cook for improvement in electromagnetic ore separators. The patent covered the use of a revolving cylinder, or drum, with poles of electromagnets in its periphery for the purpose of separating magnetic oxide of iron from substances with which it might be associated, by causing the electrornagnets when revolving as component parts of the cylinder to be successively charged to take up the ore and discharged to part with it. Since this patent was issued the science and technique of magnetism have advanced more than most other fields of endeavor. The development of electrical machinery has required and obtained better and better magnetic materials, and the science of applied magnetism is as completely and satisfactorily developed as any branch of physics. Nevertheless, the patent of Ransom Cook, issued in 1849, comes close to covering everything that is now being applied in magnetic separation. The cynic may conclude that this proves the uselessness of modern science and may point in confirmation to flotation, which has grown in a few years, practically without benefit of science, to be the most versatile and useful of concentration methods. On more careful study, however, it appears that an accurate determination of the magnetic properties of minerals and their amenability to control by mechanical and heat treatments has not heretofore been made. The first essential, therefore, in the design of improved magnetic separators has been missing. In spite of this hiatus in scientific data inventors have been busy, and patents are on file covering mineral separations by means of nearly all known magneto-mechanical effects. Because of a lack of knowledge of mineral properties, most of these inventions never worked well enough to find commercial use. The Metallurgical Division

Jan 1, 1935

By C. H. Jr. Herty

ALMOST every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gaug-ing of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanli-ness of forging steels, both carbon and alloy. In this problem the oxidiz-ing characteristics of the slag are of prime importance.

Jan 1, 1940

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940