Search Documents

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013

By K. K. Clark, W. H. Somerton

The feasibility of reducing pressures needed to fracture formations by heating the borehole intensively has been investigated on a laboratory scale. Reductions in fracture pressures of heated Bandera, Berea and Boise sandstone cores were observed at various confining pressures, simulating reservoir stress conditions to a depth of 5,000 ft. Both permeable and impermeable borehole boundary conditions were tested. Three heating conditions were used in the tests. One group of samples was heated in a furnace to a temperature of 600C, cooled to room temperature., and then tested for fracture pressures. Two other groups of samples were heated with a borehole heater to maximum borehole wall temperatures of 625 and 792C, then cooled and tested. In all cases, heated samples showed substantial reductions in fracture pressures compared to unheated samples. The higher temperature borehole heated samples showed the greatest reduction, amounting to 70 per cent in the extreme case. In actual application to wells, it was concluded that fracture pressures may be reduced by 20 to 50 per cent by intensive borehole heating before fracturing. INTRODUCTION Hydraulic fracturing of oil and gas wells is an accepted and effective technique for increasing well productivity in many areas, but is notoriously unsuccessful in other areas. The technique becomes less interesting for production stimulation purposes when excessive fracture pressures are necessary. Formations which do fracture but require high pressures, probably form horizontal fractures. There is good evidence to indicate that some formations do not fracture at all, but yield plastically under high pressure. Thus, any technique which will make formations easier to fracture or will reduce fracture pressures is potentially interesting to petroleum producers. Horizontal fractures generally occur in planes of weakness, such as bedding planes, and at pressures equaling or exceeding the effective overburden stress. In the unusual case where planes of weakness do not exist, a slightly higher pressure must be applied to overcome the tensile strength of the rock. In general, high fluid-loss fracturing fluids are conducive to the formation of horizontal fractures.1 Vertical fractures, when they do occur, are initiated at pressures generally lower than overburden pressure and are favored by low fluid-loss fracturing fluids or impermeable boreholes. The pressure necessary to create a vertical fracture in an impermeable, elastic medium can be predicted from the so-called "thick-walled cylinder" equation: Pf = 2 or+ st.............(1) where pf = fracture pressure or = radial stress st = tensile strength of medium. This equation indicates that to fracture it is necessary to overcome a tangential compressive stress, induced by and equal to two times the radial confining stress, plus the tensile strength of the medium. If the above equation held strictly true for rocks, very little could be done to reduce fracture pressure. The tensile strength of the rock might be reduced somewhat, but any change in st would be small compared to the magnitude of the tangential stress at reasonable subsurface depths. Laboratory tests have shown that actual fracture pressures exceed values predicted from Eq. 1 by factors of 1.4 to 28.6.1,2 Eq. 1 thus does not properly describe the

Jan 1, 1966

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high-speed photography to better understand the mechanisms of fracture and fragmentation.CITATION:Fourney, W L, 2015. The role of stress waves and fracture mechanics in fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 27–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A. Rosen, P. Wynblatt, J. E. Dorn

The temperature, strain rate, and structure dependence of the flow stress in a poly crystalline Fe-2 pct Mn alloy was investigated between 77" and 370°K. It was possible to identify the low-temperature data from 77° to 160°K with Dorn and Rajnak's theory of the Peierls mechanism of plastic deformation. Above 160°K one or more thermally activated mechanisms must he operative; however, these were not identified in this investigation. The mechanistic basis for the rapid decrease in the flow stress of bcc metals with an increase in temperature over the low-temperature range is yet being debated. Various dislocation mechanisms have been suggested in the past but the agreement between the various proposed theories and the experimental results have not been definitive. In the present paper, the authors will demonstrate that the plastic behavior of polycrystalline iron containing 2 wt pct Mn plus interstitials agrees excellently with predictions based on the Peierls mechanism from 77" to 160°K whereas from 160" to about 370°K other as yet unidentified thermally activated mechanisms take over. Undoubtedly, the overlap of these mechanisms with the Peierls mechanism contributed to the difficulties of rationalizing the low-temperature behavior of iron and its alloys. I) EXPERIMENTAL TECHNIQUES AND RESULTS Although extensive data are now available on the effect of temperature and strain rate on the flow stress of various bcc metals and alloys, it was, nevertheless, deemed necessary for the objectives of the present study to obtain highly accurate data of the type most pertinent for checking the theories on a series of well-documented work-hardened states. Iron containing 2 wt pct Mn was used in this investigation in order to obtain a lower ductile to brittle transition temperature than that for iron.' The additional elements present were 0.004 pct C, 0.05 pct 0, 0.004 pct S, 0.003 pct P, 0.006 pct N, and 0.001 pct Si. The as-received 3/8 by 3/4 in. bars were cold-rolled to 0.100-in. thickness, recrystallized under argon for 30 min at 1073"~, further cold-rolled to 0.063-in. thickness, and finally recrystallized under argon for 30 min at 1000°K. This treatment gave a stable reproducible equiaxed grain structure having an average grain diameter of about 90 p. Prior to the final recrystallization treatment, the sheet was machined into tensile specimens 1/4 in. wide having a 1.625-in.-long gage section. All specimens were tested in controlled-temperature baths on an Instron Testing Machine. For convenience in the theoretical analyses the data will be given in terms of the shear stress for flow, 7, the shear strain rate, f, and the shear strain, y. A series of three standard strain-hardened states were obtained by prestraining specimens at 300°K and at a shear strain rate of 7.68 x lo-' per sec to three stress levels of 6.89 X l08, 10.3 X lo8, and 14.5 x 10' dynes per sq cm, respectively. Immediately following this prestrain the temperature bath was changed and each specimen was pulled in tension at either f = 7.68 X lo-' or f = 3.06 X 10"3 per sec. In terms of the accuracy that was achieved, the values obtained did not deviate more than *0.1 X 10' dynes per sq cm and * 1°K from the reported values of stress and temperature and not more than *5 pct in the reported values of the strain rate. The tensile stresses were converted to shear stresses using a factor of 1/2. The shear stress for the initiation of flow at the test temperature was determined by taking a y = 6.16 x 10'3 offset. from the modulus line at which point good accuracy could be achieved in determining y and the associated flow stress 7, with only a negligible increase in the pre-

Jan 1, 1965

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

By Arthur R. Still, Paul Gilmour

The ore deposit of the Iron King mine occurs in a group of steeply-dipping metamorphosed eugeosynclinal volcanic and sedimentary rocks of Precambrian age. Within this sequence, the ore deposit lies at the contact of a unit made up of rhyolitic tuff and interbedded andesite and a structurally underlying series consisting of andesitic tuffs, minor rhyolitic tuffs, and argillaceous sediments. Field evidence suggests that these rocks have been overturned. The ore deposit is made up of a series of overlapping, conformable or bodies consisting of massive pyrite and associated lenses of massive quartz. These contain recoverable amounts of gold, silver, lead, zinc, and copper. A parallel zone of copper mineralization occurs within the hanging-wall rocks. The deposit is considered to belong to a large and important group characterized by mineralogical composition and the lithology and structural type of the host rocks. Evidence regarding the origin of the deposit is reviewed, and it is concluded that the ore bodies were formed through the agency of volcanic hot springs on, or near, a submarine surface of deposition

Jan 1, 1968

WMS an Operation Service and Tool WMS is a the new SNC-Lavalin solution to complete and support your site?s operation. It targets phases in the project cycle including mechanical completion, pre operational verification and commissioning. The goal is to track phases completion and electronically deliver a plan with hand over documents.

Aug 1, 2013

By R. R. Tatiya

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993

By Adriana de Oliveira Vilela

A produção de carvão vegetal em Forno Container Rima (FCR) consiste em um processo semi-contínuo composto por fornos cilíndricos metálicos móveis, com exaustão forçada dos gases. Cada ciclo se divide em 4 fases: carregamento, carbonização, resfriamento e descarregamento. Após o carregamento com toletes de madeira, 20% de umidade, o forno é deslocado para plataforma de carbonização, onde permanece por 3 a 4 horas. A entrada de oxigênio no interior do forno é regulada para controle das reações de pirólise. Todos os gases gerados são conduzidos a um sistema de queima para aproveitamento da energia e eliminação do metano. O peso, a temperatura e a pressão no interior do forno, bem como a vazão, composição e energia do fluxo de gás, são monitorados continuamente, em tempo real. A carbonização finaliza quando é atingido o rendimento gravimétrico de 35% em carvão e 60% em gás. O carvão ainda quente é transferido para cilindros de resfriamento, permanecendo por 12 horas. O forno então, é novamente carregado e se inicia um novo ciclo. Cada plataforma de carbonização pode gerar 1MWe de potência elétrica, produzir 20t/mês de alcatrão, 450t/mês de carvão vegetal e eliminar 500t/mês de CO2 equivalente. Cada FCR substitui 60 fornos Rabo Quente, reduzindo em mais de 50% a mão-de-obra braçal dos processos tradicionais, pela valorização, humanização e qualificação deste trabalho. O carvão produzido atende aos quesitos necessários para uso como redutor na metalurgia e na siderurgia.

Aug 16, 2017

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By Alizeibek Saleimen Nader

The intensive use of computers for mineral application at Serrana's phosphate mine in Jacupiranga, State of Sao Paulo, Brazil, began in the late seventies. The early hardware and software available are described in sufficient detail to allow comparisons between that solution and the new one, based on a personal computer and a new software package - PC MINE SYSTEM from GEMCOM SERVICES INC - that provides full color graphics capabilities plus mine design and planning tools. The process needed for adaptation to the new technology' and its impact on SERRANA S.A. DE MINERACAO are described. Finally, future enhancements to the System and mine control and planning are focused.

Jan 1, 1989

By Jarrett. K. M.

Nobody has, as yet, made a perfect machine. Therefore, when a machine is operating and functioning as it is designed to do, there is always some vibration present. This is easily and simply measurable with present-day equipment and any increase in the amount of vibration will indicate a potential failure. When an increase is noted, vibration analysis can pinpoint the cause of the potential failure and remedial action can be taken before an unscheduled shutdown is necessary or a breakdown occurs.

Jan 1, 1972

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By Rajesh Kumar Mishra

About 500,000 troy ounces of Platinum Group Metals (PGM) will be available for recycling each year from spent automobile catalytic converters in North America alone. Platinum Group Metals? from spent catalyst can be extracted by Hydrometallurgical, Pyrometallurgical or Gas Phase volatilization processes. This paper is a review and comparative study of various processes investigated for PGM extraction. A number of processes described in this paper have already been commercialized. The technical and environmental aspects of the important processes are discussed.

Jan 1, 1989

By M. P. Adamson, Bryson D. Trexler, R. V. Ramani, Mark L. Koenig, V. Rajaram, Alan Burton, C. S. Crocker, Kim. Y. C., A. G. Law, William C. Larson

Another record year vas experienced by the mining industry as the value of nonfuel minerals production soared to $23.5 billion-up 15% from the previous year. Based on preliminary estimates by the Bureau of Mines, US mine output was the basis for about $225 billion worth of minerals-derived materials. Metal mining accounted for $8.5 billion, or 36%, of the total. Of the 22 metals produced in the US, 11 showed quantity increases, while 16 had value increases. Business Week's survey of 1200 companies (Mar. 17, 1980, pg. 81) revealed that 21 metals and mining companies had sales increases of 30% with earnings up 104%. Higher prices and increased demand for metals were primary factors behind the improved performance. The steel sector reported a 30% decrease in earnings for the year, but the slump was primarily the result of a $383-million loss for US Steel coupled with a 17% decrease in earnings at Inland Steel. Other firms did well in 1979, with earnings up 279% at Interlake and 269% at Kaiser Steel. Major obstacles facing the steel industry included substantial tonnages of dumped and subsidized imports, environmental expenditures, runaway inflation, and price controls. Turning to nonmetallic production, of the 49 commodities reported by the US Bureau of Mines, 29 had higher outputs and 39 had increased values. While production statistics may seem encouraging, government regulations continued to stifle industry efforts to develop needed new capacity. A case in point may be publication of the Environmental Protection Agency's simplified procedure to streamline five permit programs by consolidating them into one. The five included: hazardous waste management, national pollution discharge elimination, dredge and fill, underground injection control, and prevention of significant deterioration. The new procedure, published by EPA in the Federal Register, took 149 pages. AMC's J.A. Overton, Jr., noted that (MCJ, Nov. 1979, p. 39) to visually depict the complexity of the proposed regulations, Sell Oil Co. developed a flow chart mapping a path through one section. The chart required 10 days to map and two weeks for two draftsmen, using computerized drafting techniques, to plot the results. Overton said, "Perhaps the greatest service EPA has performed in preparing its proposal is to demonstrate again that federal regulations have become a complexity compounded by confu¬sion that culminates in a conundrum." While regulatory agencies promulgate new regulations, the lack of a cohesive government minerals policy remained a matter of significant importance to mine management. A non-fuel minerals study to provide input to the Administration for a national minerals policy program was a dismal shock, according to Rep. Jim D. Santini (D-NV). He said the first phase of the program, which was to identify industry problems, failed to come to grips with the hard decisions necessary regarding these problems, their impact, and their interrelationship. Santini said the report failed to acknowledge government's role in the process and absolved the government of any adverse influence on the domestic minerals industry. In response to the phase one report, eight senior mining executives testified before Santini's House Subcommittee on Mines and Mining concerning mineral supply, access to foreign sources, environmental protection, conservation and recycling, national security, and capital formation. By year's end, Rep. Santini promised to prepare a hard-hitting committee report on problems affecting the non-fuel minerals industry to provide a better base for subsequent policy recommendations (MCJ, Jan. 1980, p. 34). On the technological front, interest again centered on mechanization, automation, and scaleup to improve and expand production. Computer use increased for calculation of ore reserves, mine planning, operations research, and mineral processing.

Jan 5, 1980

Frank Clemes Smith, Deadwood, 8. D. (communication to the Secretary): The reading of Mr. Chance's interesting paper suggests a few ideas relative to his discussion of certain Black Hills gold-ores. Mr. Chance refers to his examination, in 1897, of " the (Carboniferous) limestone plateau-country which encircles the central area of the Black Hills," and says that " it had been generally assumed that the mineralization of this formation was confined to the northern area;" further, that he "found, however, a general mineralization, extending in zones or belts throughout the region," and that the ores, being more or less specially

Jan 1, 1900

By E. P. Mathewson

The early development of the reverberatory furnace for smelting copper-ores was the work of the Welsh smelters, particularly those of Swansea. The first record of a reverberatory furnace is made by Jars, who states that in 1755 copper-smelting was effected .in reverberatory furnaces at Middleton-Tyas, in Yorkshire, England. The first patent, of any importance, for improvements in reverberatory furnaces was granted to Thomas Williams in 1778 for the granulation of the regulus. The next was that of William Evetts, in Sheffield, in 1812, for the cooling of the fire-bridge by the admission of air. Charge-hoppers above the furnaces were in common use in 1848. The size of the hearth of the furnaces about the beginning of the 19th century was commonly 11 by 8 feet. No material development was made until the Welsh process mas brought to Colorado, where Richard Pearce, as manager of the Argo works, near Denver, developed the furnace to meet the requirements of a custom plant, under keen competition with lead-silver smelting-plants, using blast-furnaces. His improvements are outlined in Fig. 1, elaborated by permission from E. D. Peters's excellent work,' to which the reader is referred for further details. This figure shows that the furiiaces were in 1878, 9 ft. 8 in. by 15 ft. in hearth; and in 1894, 16 by 35 ft., while the capacity of the furnace had been increased from 12 tons per 24 hr. to 50 tons in the same period.

Jan 1, 1913