Search Documents

By Deepak Pappusetty, Miguel A. Pando

This study is motivated from the increased interest in recent years to explore use of Ocean Energy Converters (OEC’s).OEC’s can be tidal or generate electricity from wave or current action. Design of foundation systems for these OEC’s is a key consideration as it can represent about 35% of the initial installation cost. The primary focus of this paper is related to foundation systems involving monopiles where a key design consideration includes gradual accumulation of pile head deformations beyond serviceability limits of the OEC. This design consideration is important since these foundation systems are often subjected to more than 108 low amplitude repetitive dynamic load cycles during a normal 30 year design life. Research on single model piles installed in sand and subjected to over 104 low amplitude lateral load cycles have shown that pile head displacements and rotations tend to increase gradually with increasing load cycles. This gradual development of pile head deformation is related to plastic strain accumulation in the soil in the vicinity of the monopile. Analytical methodologies based on conventional p-y curves typically cannot predict these accumulated pile head rotations and displacements. Even 3D dynamic Finite Element Analyses may not capture this response for several conventionally used soil constitutive models. This manuscript presents predictions using p-y based methods as well as 3D dynamic finite element analyses. The different numerical predictions are compared to available experimental data. Results from this study show that conventional p-y methods do not predict the gradual pile head displacements observed experimentally. Modified p-y curves, developed for cyclic loading, do a better job than conventional p-y curves but tend to greatly under predict deformation. This is believed to be related to the cyclic load test data used to develop these cyclic p-y curves which involved at most up to 500 cycles and did not include high frequency contents or partial unloading cycles. The 3D FEA captured reasonably well the general observed trends of gradual accumulation of pile head rotation and lateral deformation with increasing constant amplitude lateral load cycles.

Jan 1, 2015

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By Tristan Worsey, John Henchion, Nathan Rouse, Yannick Lauras

"This paper presents an approach used to plan and evaluate drill and blast trials for a mine that currently mechanically excavates in-situ rock. The document presents the approach used to plan the trials, the key performance indicators (KPIs) that were necessary to evaluate the mining methods, the test matrix used during the trials, and the results of the trials. The trials, which occurred as part of an overall drill to mill optimization project at this site, helped to evaluate various blast designs using fragmentation results,drilling and blasting costs, and downstream costs. This project was unique in that (1) drill and blast methods were trialed on multiple rock types and various bench heights using a range of blasthole diameters and powder factors and (2) the load and haul costs were evaluated using a range of loading equipment, from 66 tonne (73 ton) excavators up to 250 tonne (276 ton) excavators. A ten year net cost financial evaluation of the material extraction alternatives was also prepared for the site management. Ultimately, the process of evaluating the drill and blast trials helped the management decide whether to continue extracting using mechanical methods or to introduce drill and blast methods to extract the rock."

Jan 1, 2017

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By F. Rivard, L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. Retrofitting plasma torches in place of fuel oil burners lead to lower operating costs, capital cost and greenhouse gas emissions.INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes [!]. Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid start-up and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate [2]. Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates."

Jan 1, 2013

By DONALD H. McLAUGHLlN

Few factors have had more influence in maintaining the strength and stability of the United States than our persistent habit of providing .checks and balances to the dynamic powers of free enterprise on the one hand and to the controls and guidance exercised by the State on the other. .Indeed, it is this same concern for matching forces against each other that has given our republic its ability -to preserve a democratic basis of life for its citizens, and yet maintain a ,government that is able to protect the rights of all and to resist and minimize the danger of excessive concentration of authority. Our current efforts to clarify the nation's mineral policies and to define more clearly the role that the governmental agencies should play in conjunction with the functions of private -enterprise again reveal the desirability and advantages of maintaining our traditional controls. At times, the equilibrium has been temporarily disturbed by too great enthusiasm for one or the other of these basic concepts. Sooner or later, however, the balance has been restored by the healthy opposition that is always created by excesses of one sort. At the current stage in our history, the swing toward undue enlargement of the powers of the State seems to have gone dangerously far and we would be untrue 'to our traditional behavior if the group that must demonstrate the virtues of free enterprise did not rally to its support with the utmost earnestness.

Jan 1, 1949

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle and Ballard. These connections include considerations for both elevated and tunnel alternatives in West Seattle and Ballard, as well as a new tunnel and six underground stations in the densely developed downtown Seattle. This paper describes the conditions and constraints along the corridor, and the latest development in the ongoing process to plan the underground guideways and stations.

Jun 13, 2023

FROM time to time articles have appeared in the technical press on the interesting subject of surface combustion. The theoretical part of the problem has, for practical purposes, received ample consideration in those articles, but the number of practical applications of surface combustion referred to has generally been very small.It is the writer's object to review some recent developments in surface combustion, and also to try to arrive at an estimate of its advantages and possibilities. It is not necessary for this purpose to dilate upon the phenomenon of surface combustion itself. Many interesting things have been said on the subject by Pro£. W. A. Bone, of Leeds, to whose researches the recent developments are largely due. A few illustrations may make clear what is meant by surface combustion.Prof. Bone, in an experiment, took a platinum crucible, which he heated in the flame of a Meker-burner. Then he turned the gas off for a second, and, opening the stop-cock again, allowed the combustible mixture to impinge upon the crucible, thetemperature of which was still well below the ignition temperature of the gas. Although no flame was visible at this stage, it was soon clear that, nevertheless, the gas and air had continued to combine, as the crucible would attain a red heat after a few seconds.Another instance of surface combustion was shown by a Mr. Fletcher, in 1882. He placed an iron ball, weighing 3 lb., on a slab of fireclay, heated it for a few seconds with a blow-pipe, and blew the flame out, leaving the gas-mixture still...

Jan 1, 1915

By G. W. Jones

Among its investigations into the prevention of waste in production and use of oil and gas, the Bureau of dines has made considerable study of the efficient utilization of gasoline and by-product distillates in motors, this being done chiefly by measuring and analyzing the exhaust gases therefrom. A number of reports3 of a highly practical nature have been published and are available on this subject. The results of these tests have shown that the average motor vehicle wastes approximately 30 per cent of the heat value of the fuel used, as incomplete combustion products - carbon monoxide, hydrogen, and methane, These unnecessary large heat losses are mainly due to improper carburetor adjustment, and by proper¬ly adjusting the carburetors for maximum power and efficiency a large part of this heat loss can be eliminated. This in turn results in an increased mileage per gallon of fuel used.4

Jan 1, 1924

By E. J. Duggan

In the course of the grinding experiments conducted at Climax over the past twenty years one interesting phenomenon was discovered. This was that balls made of certain types of steel grind more ore than some others. The most significant variation was found in the results secured with a hard alloyed forged bail compared with the forged carbon ball supplied by most ball manufacturers These findings were confirmed in many repeated controlled tests. The value of these tests depends on the methods used, the facilities available and the care with which the investigations were conducted. These are described in the following. This testing has largely been done in eight 91 x 81 low discharge ball mills in closed circuit with 7811 duplex screw classifiers. The mills run at 20 RPM on a feed approximately minus 3/8 inch. The ore is ground through 28 - 35 mesh in one stage. Each mill and auxiliary classifier is in a separate, parallel grinding and flotation section The, ore to each: section is the same in every particular and is fed to each mill bin from a common conveyor tripper. The ore from the bin to the ball mill is weighed on a conveyor scale. The power input to each mill motor is determined with a watt hour meter which measures the power to the mill motor only. Both the scales and meters are checked periodically by standard methods and have been found to give consistent readings. Automatic samplers are employed on each section to obtain accurate measurement of the size reduction. A size analysis of the classifier overflow is made each shift and a composite size analysis is obtained from a weighted average of the various shift analyses. The mills are driven by 450 horsepower synchronous motors so that there is no speed variation and shell liner age is kept as nearly the same as possible in mills under test. The same set of operators is assigned to a mill under test as to the control mill. In all other particulars such as ball load, mill density, liner design, etc., the mills are operated in precisely the same manner. This is an ideal arrangement for plant testing. From observations of ball mill performance over the past twenty years, it is the opinion of the operating staff that variations of as little as one to two percent in mill capacities may be determined if sufficient operating hours are devoted, to a test. Relations between mill capacities, fineness of grinds and power consumptions have been established with a high degree of accuracy. In Table I are given the figures for one test. These show that while the grind with the hard ball was slightly coarser, the tons ground per hour was 5.4 percent greater with the soft ball, and 6.1 percent greater on the basis of minus 100 mesh produced. The power consumed per ton with the hard ball was 4.4 percent greater on a tons per hour basis. The soft ball was inferior in wearing qualities and steel consumption per ton of ore was 24 percent greater with it. In this test the mills were charged with the two different balls for a period of three months to allow the ball loads to come to equilibrium. In Table II are given the specifications of the two balls. The difference in grinding rates may be accounted for by the nature of the ball surfaces. The surfaces of the soft balls after being worn a while are rougher to the touch. Enlarged photographs of the worn-in surfaces of hard and soft balls are shown in Figure I. These show the presence of scratches or skid marks on the hard ball surface which indicates less nipping effect. The Climax ore pulp has a pH of 6.0 and is in a dispersed state. The viscosity is low compared with most ores especially those that are conditioned with lime. This would lower the tendency of the pulp to adhere to the balls with a lower grinding efficiency as a result. It was also thought that the relative rates of wear from surface to center might affect the make-up of an equilibrium ball charge. This probably has little effect on capacity as shown by the size analyses of the two ball charges in Table III. This hypothesis was subsequently investigated by the use of rationed charges. The rationed charge did not overcome the advantage in

Jan 1, 1958

By B. Skrotzki, E. Augenstein, C. Rockenhäuser

"The aluminium alloy 2618A is an Al-Cu-Mg alloy with additions of Fe and Ni, which is designed for long-term operation at elevated temperature in transportation and aerospace industries. The alloy degrades due to coarsening and dissolution of GPB zones and coarsening of S-Phase precipitates (Al2CuMg). This work investigates the overageing process at the application relevant temperatures of 190 °C for durations ranging up to 25,000 h. The nm-sized precipitates were selectively imaged along the <001>a direction of the Al matrix using dark-field transmission electron microscopy. The resulting images were then evaluated and allow the statistically relevant determination of radii distributions and the average radius of the precipitates dependent on temperature and heat treatment duration. Ostwald ripening of the S-phase does not describe the ageing process adequately. Instead, the evolution of GPB zones during the initial ageing regime needs to be considered in addition to the coarsening process of the S-phase. DSC measurements were performed to determine the presence of GPB zones in different ageing states. This will allow a quantitative description of the ageing process and a comparison to samples aged under external load.INTRODUCTION Alloy 2618A is an Al-Cu-Mg alloy, which is part of the 2XXX series of aluminium alloys. It is used in aerospace and transportation industry due to its desirable material properties for long term operation at elevated temperatures (Polmear, 2006). Fe and Ni are added to form intermetallic compounds, which retain microstructural stability at elevated temperatures (Bergsma, Li, & Kassner, 1996; Elgallad, Shen, Zhang, & Chen, 2014; Oguocha, Yannacopoulos, & Jin, 1996; Wang & Yi, 2006). The size and distribution of the nm-sized S-phase formed from the supersaturated solid solution (SSSS) during heat treatments mainly controls the strength (Khan, Starink, & Yan, 2008; Liu, Zhang, Ding, Sun, & Chen, 2003; Parel, Wang, & Starink, 2010; Shih, Ho, & Huang, 1996; Wang, Starink, & Gao, 2006). The S-phase has the composition Al2CuMg and is orthorhombic under equilibrium conditions (Heying, Hoffmann, & Pottgen, 2005; Perlitz & Westgren, 1943). Early experiments proposed the following decomposition of the S-phase sequence during heat treatments (Hardy & Heal, 1954; Silcock, 1961):"

Jan 1, 2018

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product&apos; (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world&apos;s nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By Wm. A. Haven

As soon as the likelihood of American participation in the war was established, and in spite of the fact that we can produce almost as much as all other countries combined, the demand for prompt deliveries of iron and steel products from American factories began to exceed their utmost capacity, and, after fifteen months of practically full operation, has continued to do so. Therefore, it would seem worth while to review some of the aspects of the supply and demand for steel as well as the efforts that are being made to bring them into balance. It is still being debated as to whether the situation should be defined as a real shortage that will persist through the emergency period or as a temporary one than can be relieved by less drastic measures than a Government-sponsored program of expanding existing plants and building new ones.

Jan 1, 1942

By R Zavadil, S Kuyucak, F Fazeli

Proton exchange membrane (PEM) fuel cells generate electricity by reacting hydrogen and oxygen. A thin, bipolar electrode material provides a medium for electron exchange with the electrolyte, alternately serving as anode at the hydrogen-rich side and cathode at the oxygen-rich side. Stainless steels have sufficient corrosion resistance to qualify as bipolar plate materials. However, the protective chromite layer increases the contact resistance, the battery’s internal resistance; and thus, decreases the electrical efficiency of the fuel cell. A heat-treatment is proposed and investigated via simulation by ThermoCalc / Dictra and experimentally, to generate a sufficient quantity of conducting surface carbides that breach the protective layer. Once carbide growth is arrested, a subsequent heat-treatment is also needed at a higher temperature to restore the corrosion resistance by filling-in the Cr-depleted layer (sensitization) around the carbide particles.

Jan 1, 2014

By Joshua C. Adams, Les Chernauskas, Edward L. Hajduk

"Drilled shafts are increasingly being used to support bridge and building foundations. Because these foundations usually carry very high design loads and often serve as non-redundant, single load carrying units, these foundation systems need a high level of quality control (QC) and quality assurance (QA) during construction. One such method for providing QC/QA is crosshole sonic logging (CSL) testing, in which ultrasonic signals sent across the drilled shaft concrete assess concrete quality.CSL testing is an effective tool to evaluate the integrity of the in-place drilled shaft concrete. While typically used to evaluate drilled shaft concrete after construction, CSL testing can also be used to evaluate drilled shaft repairs. This application can be difficult, given the variability of repair methods and material properties. CSL testing can also be adversely affected by the condition of the concrete/access tube bond, leading to false anomaly detection and/or inability to evaluate concrete integrity effectively. This phenomenon, called access tube debonding, is often located in upper portions of the drilled shafts where large changes in groundwater occur, such as within tidal zones.Two case histories showcase innovative uses of CSL testing to deal with consistent access tube debonding and to evaluate drilled shaft repairs.CSL OverviewCSL testing involves placing ultrasonic transmitters and receivers in access tubes installed in the drilled shafts prior to concrete placement. Concrete quality is assessed by examining the First Arrival Time (FAT) and relative energy of the signal sent between the transducers. If the distance between the access tubes is known, an apparent signal velocity (i.e., wave speed of the ultrasonic signal through the concrete) can also be determined and used to assess concrete quality.Common CSL testing practice consists of simultaneously raising the ultrasonic transmitter and receiver and recording the ultrasonic signals with respect to depth. This results in a 2D examination of the"

Jan 1, 2009