Search Documents

By Nar S. Dalal, Xianglin Shi, Val Vallyathan

"INTRODOCTIONIn an earlier communication 1 from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates of free radicals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubini et al.2 have also reported the detection by electron spin resonance (ESR) of the formation of SiO. and Si-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum ( -10-10 torr>3 and subsequent exposure to air,3 and to other gases,4 these radicals were identified2 as being formed by the homolytic cleavage of the Si-0-Si bonds and the reactions of the Si• and SiO- radical with atmosphere. Fubini et al.2 also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anca5 bad reported that lipid ·peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radica1 studies on a given quartz dust sample have been reported, except for some earlier work from our laboratory.1·6·7 We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radica1 measurements on a freshly made quartz dust. The dust's free radica1 content was measured using ESR spectroscopy while its cytotoxicity potential was estimated via hemolysis. Hemolysis was employed as the toxicity test because it is a widely used method for estimating the potential of a dust for disrupting the cell membrane. 8 The fibrotic potential was followed by measuring the dust-induced lipid peroxidation, using linoleic acid as a model lipid. As discussed below, the results obtained suggest new clues to the mechanism of the quartzrelated cytotoxicity and fibrogenicity. MATERIALS AND METHODSReagentsCrystalline quartz particles with a size range of 0.2-2.5 mm were obtained from the Generic Respirable Dust Technology Center, Pennsylvania State University, University Park, Pennsylvania. These particles were crushed in air to obtain quartz dust samples with particle sizes smaller than 20 microns. We chose to work with a dust with mixed particle sizes, rather than a specific range, as an effort to simulate the mining atmosphere. An agate mortar-pestle arrangement was used for the crushing and grinding because of the close similarity of the structure of agate to that of quartz. Diethylenetriaminepentaacetic acid (DETAPAC) were purchased from Sigma. All other chemica1s were purchased from Fisher or Aldrich.Hemolysls ExperimentsHemolytic activity of silica was measured, following an established procedure,9 as the amount of hemoglobin released from a 2 % suspension of sheep erythrocytes after incubation with 10 mg of silica dust for one hour at 37 °C. The hemoglobin release was estimated via the absorbance at 540 nm using a Gioford spectrophotometer. The procedure was calibrated by substituting the silica dust by a phosphate buffer solution as a negative control (background) and O.S % Triton-X-100 as a positive control (100% hemolysis). The percentage of hemolysis was calculated as follows:"

Jan 1, 1990

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

By G. E. McElroy

[The ventilation of development faces in mines for diluting gas or dust concentrations aid in hot mines for providing air-motion cooling affect, by fan-pipe units discharging high-velocity streams of air close to the face, is an important phase of mitre ventilation. The effectiveness of such units depends largely on the air-flow distribution between-the pipe discharge said the face, a subject on which little definite information is available. A study of the air, flow from grills into rooms3/ has provided sore basic data, but under conditions so different from mine fan-pipe installations in development ends that tae data to are of doubtful application to mine installa¬tions, owing to differences in air-flow conditions. The purposes of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pine lines in nines. The s series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of tripe, and adjacent calls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made b y short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects cue to size anti shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs is and ago se reported.]

Jan 1, 1940

By V. A. Shumsky, I. P. Polyakov, N. M. Ospanov, M. A. Lyamina, N. N. Ushakov

Studies on the kinetics of the competitive processes of PbS volatilization and PbS oxidation, as applied to the heat and mass transfer conditions in the flame of the Kivcet furnace, revealed that the rate-determining factor is the supply of heat. Therefore, low yields of fume in the autogenous flash smelting of lead sulphide feeds are noted despite the high volatility of PbS at 1,300-1,400°C. Dust formation in the autogenous flash smelting of Kivcet-smelters does not exceed 5-7%, of which fumes amount to ~ 80%. Using extra fuel during autogenous smelting involves the mismatch of the sulphide oxidation rate and the release of heat in the flame, and increases the fume yield. This is a major cause of the high dust formation in pilot plant trials. The analysis of dust formation in the Kivcet smelting of oxidized lead feeds in an industrialscale smelter shows an overall increase of dust formation (up to 10% of the feed), with fumes constituting ~ 80% of the dust. A pronounced increase of the zinc component of the fumes is also noted. Lead

Jan 1, 2000

By Robson Aguiar de Macedo

O estudo de ligas livres de Pb envolvendo o emprego de junções metálicas sob altas temperaturas tem recebido atenção especial, sendo desenvolvidas novas ligas com qualidade e desempenho adequados. Ligas Bi-Ag consistem em alternativas promissoras para a substituição das ligas de solda contendo Pb para tais aplicações, por isso devem ser melhor caracterizadas sob o aspecto de estruturas brutas de fusão. Assim, o presente trabalho objetiva investigar a liga hipoeutética Bi-1,5%Ag (%em peso) solidificada unidirecionalmente sob regime transitório de fluxo de calor. Será analisada a influência dos parâmetros térmicos de solidificação como velocidade de solidificação (VL), taxa de resfriamento (?) gradiente de temperatura (G) na microestrutura e na evolução de dureza da liga citada. Para determinação do perfil de dureza, foram realizados ensaios de dureza Vickers. Para obtenção e caracterização das microestruturas presentes no fundido Bi-1,5%Ag, fez-se o uso da microscopia ótica e da fluorescência de raios-x. Uma estrutura de dendritas facetadas de Bi circundadas pelo eutético Bi-Ag prevaleceu ao longo do lingote Bi-1,5%Ag. Verificou-se um aumento gradativo dos espaçamentos dendríticos primário (?1) e secundário (?2) à medida que a distância da base refrigerada foi aumentada. Em geral, os valores de dureza diminuíram para maiores valores de ?1 e ?2.

Aug 7, 2018

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By Frank C. Roberts

Neglecting the hydrogen and hydrocarbons, 1 will assume the following analysis as a fair average composition, by weight, of the waste gases escaping from a coke-burning blast-furnace: CO2............17.25 CO,............25.25 N,.............57.50 100.00 The 25.25 CO requires for combustion 62.6 of air, or 11.398 of oxygen, necessitating the passage of 48.202 nitrogen into the products of combustion. The latter, therefore, have the following composition: CO2,,............ 56.9 N,............105.7 Tile total specific heats of these quantities of the respective gases are 12.31 and 25.79, giving for the combined product, 38.1 approximately. That is, the product of combustion will absorb 38.1

Jan 1, 1889

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Jan 1, 2004

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By R. Franfield, W. J. Birch, L. Bermingham

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as consequence of the shock wave created by the detention of the explosive charge in a blast hole, rapidly propagating through the rock and then impacting on the quarry face.

Jan 1, 2013

Jan 1, 1963

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By Layton C. Binon

Exploration budgets are commonly determined by "rules of thumb" such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve the goals of the company. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1981

By J. F. McDermott

The problem of converting our raw coal, and especially those coals that are not suited for long storage, in other words soft, into a fuel which would be at once clean; of a high B. t, u. content and low ash, is one that has occupied the minds of many able chemical engineers and hydrocarbon technologists during the past few years. Low temperature carbonization is the present outcome of this line of research, and many methods have been evolved of recent years to turn out a serviceable, useful fuel, and at the same time, save the by-products. As most of the research and data within my experience and knowledge pertains to lignite or sub-bituminous coals, I will confine my remarks to coals of that character and grade: I might say that Colorado coals, commonly called lignite, are not in reality true lignite, but are sub-bituminous, although I have in my possession an analysis of a Colorado coal which shows a moisture of 17 per cent, volatile 31.5 per cent, fixed carbon 28.8 per cent, and an ash of 22.7 per cent, and B. t. u. less than 8,000. Even this, though useless for domestic or indeed industrial purposes, could not be classified as true lignite. However, for the purposes of this paper I will refer to these coals as lignite. Two thousand pounds, or one ton, of raw lignite carries about 20 per cent moisture. This, of course, varies in some coals, but is, I believe, a fair average. For carbonization purposes this is usually dried to a 5 per cent moisture, therefore leaving but 1,700 pounds of coal to be placed in the retort. From present knowledge, and with the average process of carbonization, 70 per cent of this coal will come out carbonized, or 1,190 pounds, to which is added about 10 per cent pitch, which is fried out as the coal passes through the retort, and which is used as a binder, making a total of 1,360 pounds of coke or carbonized coal. This is usually in appearance a dark colored, rather porous coke of about the size of pea coal. It burns without smoke and have a very high B. t. u. content. According to most authorities on this subject, carbon, hydrogen, oxygen, nitrogen, sulphur and ash constitute the only elements on which carbonization value of a coal depends, and of these hydrogen is the most important. It is claimed the value of a coal for carbonization purposes may be roughly surmised from the hydrogen content. If this is promising, that is, showing an available hydrogen content of from 3 to 5 per cent, the coal should be given a careful ultimate analysis. Should the seam, as often happens in lignite coals, show varying bands of coal of different structure or appearance, samples should be taken from each band as well as a gross sample taken down the face of the seam in the usual way. This is in order to determine what part of the seam is most promising for by-product processes. A seam showing a high nitrogen content adds to the attractiveness of the coal in carbonizing as; if available nitrogen is 2 per cent or better, it should give a very high ammonia yield.

Jan 1, 1923

By Glenn E. Johnson

The Bureau of Mines investigated the production of hydrogen cyanide by reacting powdered coal (minus 300 mesh) with ammonia at 1,250° C in a bench-scale study. Both metallic and ceramic reactors were used. Yields up to 0.7 cu ft of hydrogen cyanide per cubic foot of ammonia consumed r- obtained. The resulting ammonia conversion of about 75 volume-percent approximates conversion obtained commercially in processes utilizing natural gas and platinum catalysts. The coals that had higher volatile-matter contents gave the best yields of hydrogen cyanide. Allowing the coal to adsorb ammonia before reaction resulted in increased yields of hydrogen cyanide. Cost studies for a plant with a 40-million-pound-per-year capacity indi-cate that hydrogen cyanide can be profitably coproduced with carbon black, from coal and ammonia, at the current market price of hydrogen cyanide (11.5 cents/lb). These figures are based on heating the reactor electrically. If a cheaper heating method were devised the economics of the process would be more favorable.

Jan 1, 1967

By Christopher M. Rule, Martyn P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The methodology incorporates a flotation simulation program “SUPASIM” which translates flotation performance from bench-scale tests to full-scale plant. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist. Kelsall’s unmodified equation incorporating two rate terms describing slow and fast floating components is used as the basis of the method. The flotation behaviour of an ore is described by a set of numbers, which can be compared in the evaluation of ore types, mineralogy and operating conditions. In so doing a precise relationship is developed between metallurgical performance in terms of grade and recovery and flotation kinetics.To date the performance of more than 20 flotation plants has been predicted, encompassing copper, lead, zinc, nickel, phosphate, pyrite, graphite, cassiterite, platinum and various slags. In three cases, plants have treated more than one type of ore. The method has successfully been used to predict and design four flotation plants using data generated from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted. In the last year alone it has been used to drive flowsheet development for at least seven new plants in South Africa and the Americas. It is also being used to assist in the optimisation of existing operating plants."

Jan 1, 2003

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By B. Q. Li, Y. Shu, K Lynn

"This paper discusses the effects of magnetic field and internal radiation on the melt flow and solidification morphology during solidification processing of oxide crystals for optoelectronic and remote sensing applications. The numerical solution of the integral differential equation characterizing the internal radiation and the magnetohydrodynamic equations describing the magnetic and transport phenomena is obtained by applying the combined discontinuous and continuous finite element method. The results show that both internal radiation and an externally applied magnetic field can have important effects on the melt flow and solidification behavior during the melt processing of oxide materials.IntroductionOptical single crystals are widely used in optical and electronic devices. These crystals are often grown from high temperature oxide melts under strictly controlled conditions. As in the well-known single crystal growth processes for semiconductor wafers, thermal gradient in the melt is a major contributing fuctor to the oxide melt pool. Unlike the semiconductor single crystal growth processes, however, the oxide melt is semitransparent and internal thermal radiation plays an important role in redistributing the thermal energy in the melt pool. Our recent experience with pilot-scale plant measurements also shows that the oxide melt is electrically conducting, although its electrical conductivity is considered much lower than the liquid metal or semiconductor melt.The fact that the oxide melt is absorbing and emitting in the thermal radiation frequency range makes it difficult to study the thermal energy transport in the melt pool. This is because thermal radiation is governed by a hyperbolic differential equation, which is different from those describing the transport processes in liquids. Also, our understanding of how thermal radiation interacts with other transport mechanisms such as convection and conduction is rather limited at point in time, in particular in high temperature oxide melts for optical single crystal processing."

Jan 1, 2004