Search Documents

By O Tiili, A Dixon

Many minerals processing plants need to have greater efficiency in current times and optimise their process performance in order to maintain high profitability. This is even more so in the current economic climate. In the case of large flotation cells, such as TankCell«-300 with over 300 m3 active capacity, ensuring consistent operation and optimal flotation conditions is particularly critical, given the high impact on overall process and throughput of such cells. As there are fewer cells to control and monitor, there is also a lower initial capital cost for instrumentation - the requirements, however, are higher. Despite such compelling reasons, instrumentation and basic control in flotation cells has not changed much in recent years. The standard is still to use traditional feedback (PI algorithm) controls for slurry level and flotation air. A new advanced instrumentation and control package for large flotation cells has recently been developed by Outotec and has been installed at Macraes.In addition to the standard basic instrumentation and control, the new system at Macraes consists of a froth image analysis system, a froth velocity control, and a level control system which utilises adaptive feedforward compensation. There are three TankCell«-300 cells in operation at Macraes since November 2007 and the new control system was commissioned in December 2007.The paper will include comparative data from pre- and postsystem installation and discusses benefits including optimised recovery, improved performance, as well as ease of operation.

Jan 1, 2009

By I. Thobadi, C. Pawlik, K. Bisaka, S. Mokoena, M. Erwee

The PyEarth™ process developed at Mintek has been demonstrated successfully at pilot scale. Nine tons of ore containing 2.3 mass % of total rare earth oxides (TREO) from a dormant mineralogically complex iron-rich ore deposit, was subjected to a concentrating smelting step in a 200 kW DC open-arc pilot furnace and the rare earths from the resulting slag were extracted via a hydrometallurgical route. This ore deposit is practically not amenable to extraction by conventional methods. The testwork results proved that the PyEarth™ process was able to optimize the extraction of rare earths while minimizing waste through the removal of iron as a saleable iron alloy. Reduction of iron to the alloy in the smelting step was found flexible, efficient, and controllable, while rare earths were left virtually unreduced in the slag phase. The slag chemistry is selected to optimize both the smelting and leaching performances as well as the alloy composition. Leaching of the resulting slag was found possible and most efficient in hydrochloric acid amongst other lixiviants tested.

Jan 1, 2017

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By Gregg J. Hodges

The Stillwater Mining Co. is a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corp. The Stillwater Mine, located near Nye, MT, is the Western Hemisphere’s only primary platinum-palladium deposit. The mine began production of flotation concentrates in March 1987. In the fall of 1987, an integrated pilot plant testing campaign of electric furnace smelting and oxygen-blown converting confirmed the feasibility of further upgrading to semi-refined matte, or “white metal.” In the summer of 1990, the production smelter was brought on line. The record of the discovery and development of the Stillwater deposit, mine and concentrator has been summarized in several articles (White, 1987; Kennedy, 1987; and Hodges and Clifford, 1988). Similarly, the pilot campaign to test the feasibility of treating the flotation concentrates in an integrated smelting plant has been described (Hodges and Clifford, 1988; Matousek, et al., 1989; and Matousek and Whellock, 1990).

Jan 1, 1991

By C. Ernest Birchenall, Robert F. Mehl

APPLICATION of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion coefficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner1 derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smiths on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 ACTIVITIES IN BRASS9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by azn = Pza/Pzn° [I]

Jan 1, 1947

By Clemens Jones

THE analytical history of phosphorus in its relation to the metallurgy of iron is an interesting study, the progress of which runs parallel with the development of the greatest industry in the world. Without the means of finding out how much phosphorus crude pigiron contained, the Bessemer steel process would have been impossible. To do this was originally tedious and slow work. On the other hand, the " direct" process of to-day, as well as the various special processes for steel or iron, have demanded the utmost rapidity in the operations of analytical chemistry. In general, any rapid process for the conversion of unrefined metal into a product of standard composition depends upon the rapidity of some accurate means employed to control it. Moreover, in our modern practice, it is not improbable that the differences in physical properties among the various makes of iron or steel are affected, if not produced, by the use of different methods of analysis. Recourse is always had for correction to the ((standard methods," but I incline to think that these methods are susceptible to error. It is very certain that the system of duplicates would not be resorted to, if the fact were otherwise. Even when duplicated, under the most careful and skilful manipulation, these standard methods produce disagreements. In proof of statements like these, which may sound. heretical, I hope, further on, to cite some evidence worthy of attention. I do not now mean to lay claim to the distinction of discovering the ultimate corrective. That result will come, no doubt, in. time, as the product of the experience of many workers. In the case of phosphorus, as of the other ingredients of iron or steel, a great deal has been done to accommodate the methods of analysis in rogue to the growing necessity for more rapid procedures: Much of this work has concerned what might be called the incidents of method. There is no better example of the accumulation of these incidental improvements than the work done on phosphorus; and I

Jan 1, 1890

By R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and IR. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX (R) 64N) is capable of copper chelation. The effect of the structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1972

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

By Gilvandro Bueno

Os controles dos processos de cominuição estão normalmente associados à redução de granulometria e geração de superfície específica, usualmente utiliza-se peneiramento para medição de granulometria e permeabilímetro de Blaine para superfície específica, estes métodos são largamente utilizados para este fim. O método on line por difratômetros a laser também pode ser empregado para estas medições na indústria, como se trata de uma tecnologia recentemente adaptada para ao processo de Pelotização, foi necessário validar o equipamento e determinar equações de correlação de leitura com os equipamentos existentes. O trabalho consistiu em realizar uma série de amostragens cujas amostras foram analisadas no equipamento industrial a laser, em seguida analisadas em laboratório. As equações de correlações obtidas foram inseridas no equipamento industrial de medição on line por laser tornando a leitura familiar aos obtidos pelas análises de laboratório, onde foi possível garantir confiabilidade para tomadas de decisões.

Aug 1, 2018

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By Freeman Bishop

President Allende says he will expropriate all American investments in Chile and he's already well on the way to accomplishing this objective. What the average observer doesn't realize is that this has not only created big lossess for the copper companies. It could also take a chunk out of the U.S. taxpayers' pockets. Premier Castro expropriated the U.S. taxpayers' investment of over $100 million in the Nicaro (Cuba) nickel and cobalt operations-and U.S. Government protest over the loss was never heard above a whisper. Where the taxpayer comes in today is through the Overseas Private Investment Corporation, which was set up to guarantee U.S. companies' foreign investments against losses due to political changes. As of now, metals firms hold more than $300 million worth of obligations against this U.S. Government agency. The agency itself may not be able to raise more than $85 million, and a supplemental appropriation may be needed to meet its guarantees.

Jan 1, 1971

"The Industrial Comminution Efficiency (ICE) working group, part of the Global Mining Standards and Guidelines Group (GMSG) has engaged a large number of industry professionals representing mining companies, equipment vendors, consultants and metallurgical laboratories with interests and capabilities in the comminution field. These participants have collaborated to develop three guidelines for the assessment of the efficiency of mineral comminution circuits. Two of these guidelines deal specifically with power based modelling techniques to quantify energy efficiency using widely practiced techniques, those developed by Bond (1961), Rowland and McIvor (2009), and Morrell (2009). The third guideline deals with the sampling and surveying of grinding circuits as is required to provide the necessary information, at appropriate quality, to furnish the efficiency analysis promoted by the first two guidelines. This preprint will focus on the Guideline on Methods to Survey and Sample Grinding Circuits, which is currently in the final stages of peer review and finalization by the GMSG. INTRODUCTION It is important to make a clear distinction on the scope of work of the GMSG guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and as a result require a large amount of information to calibrate and validate the unit models. As a result these surveys are labour intensive, somewhat expensive depending on internal capabilities of the mine site or company, and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions. As a result of these factors full grinding circuit surveys are not a common occurrence at a large number of facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices. To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. It can also be manipulated by experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, supporting an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2016

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By J. L. SCHUELER

THE writer has reread Mr. Ingalls' interesting article in the July, 1923, issue of MINING AND METAL- LURGY on "The Use of Spelter in Galvanizing." It seems that most writers, in commenting upon coatings of spelter on sheets and wire, dwell upon the thin coatings which these materials carry, and rightly so. However, they seem to forget that until very recently, in the case of wire, the manufacturer did not know how to apply a heavy coating of spelter to the wire, especially if the wire was to be woven into fence or fabricated in some other manner, because heavy coatings of spelter are exceedingly brittle. This is even true in the case of high-grade spelter, but to a lesser degree than with Prime Western. Because of this brittleness, it has been necessary for wire manufacturers to smooth the coating by passing the wire through tightly compressed wiping means of some kind, usually asbestos. This removes all of the excess spelter and allows only a thin coating to remain. The latter, as a rule, is malleable and the wire can be fabricated without material injury to the coating.

Jan 1, 1924

By P. T. Velu

Solubility of metal oxides in the molten salt electrblytes is an important parameter in the electrochemical processing of metals and alloys. The efficiency of an electrochemical process primarily depends on the quantity of metal oxide present in the electrolyte in the dissolved form and its thermodynamic properties. The activity of CeO2 was calculated using the free energy of fusion of CeO2,{ AG°m, CeO2. The AGOm,CeO2 }was deduced from the values of enthalpy, heat of fusion and melting point of Ce02. The activity coefficients of CeO2 as a function of temperature and melt composition were calculated. The thermodynamic data such as integral molar enthalpy, entropy and Gibbs energy of formation were calculated as a function of composition and temperature.

Jan 1, 1994

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By H. Y. Sohn, M. Pérez-Tello, J. Löttiger

An investigation of the oxidation reactions of two industrial copper mattes was performed using dflerential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) at heating rates of 20°C and 8°C/min, respectively. The temperature of incipient reaction, the total exothermic and endothermic heats of reaction and the weight change during the oxidation process were measured as functions of the oxygen concentration in the oxidizing gas, matte grade and matte particle size. The temperatures of incipient reaction measured from the DSC experiments were found to increase monotonically with all three input variables. TGA experiments showed that Cu2O and CuO CuSO4 are formed before the complete oxidation of Cu2S to CuO.

Jan 1, 2000

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001