Search Documents

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Xun Zhang, Huiqing Tang

The inner shape of a blast furnace is of fundamental importance for blast furnace ironmaking to achieve goals of high yield, high quality, low fuel rate and long campaign life. Therefore, it is worthwhile to design better furnace inner shapes. This paper conducted numerical simulations of performance for the blast furnaces with conventional and modified inner shapes. By comparing the calculation results of the two blast furnaces with the same operation conditions, it can be found that there are some certain differences. It is necessary to optimize the inner shape of blast furnace considering the results of simulations. This paper provides references for future blast furnace inner shape design and related technology developments.

Mar 1, 2017

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Geoff C. Knight

Longwall mining using the shearer is acknowledged internationally as the most economically successful method of high volume production from underground coal mines. Since its introduction in the 1950s, a great deal has been achieved in developing the capability and reliability of the shearer - and the associated face conveyors and powered roof supports - to produce the competent systems now widely deployed. Equipment will continue to improve as knowledge and experience are gained and through the influence of market forces on the international equipment suppliers. However, current systems are so successful that further improvements are likely to be incremental rather than radical unless a high level of system automation is introduced. The automation concept is not new to the shearer-based longwall system. The opportunity and the need were recognized soon after the shearer and powered support were introduced in the 1950s. In the early 1960s, the British Coal Corp. (BCC; then the National Coal Board) attempted remotely operate longwall systems. Those imaginative early schemes were seen as failures at the time. But, with hindsight, a great deal was learned from the experience that stimulated automation research in several European countries. One of the most fundamental lessons learned was that coalface system automation is not possible until there is a high level of competence in automatically controlling the operation of the production machine itself within the coal seam. Once that is achieved, the rest of the system will follow with comparative ease.

Jan 1, 1991

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By D Stow, R Goodridge, K J. Molloy

A range of explosives has been specifically developed for soft ground blasting. These explosives can be used in both wet and dry blasting conditions, range in density from 0.3 - 1.2 g/cc and range in VoD from 2 - 4.5 km/s. This range of explosives has the potential to be tailored to ground type and is predicted to be suitable for a variety of applications which include: blasting in soft to medium overburden, coal blasting, wall control, and low vibration blasting. Trials have been conducted in several applications with encouraging results. Several cast/throw blasts have been conducted with these products partially replacing either ANFO or Heavy ANFO. The results from the blast have been equivalent in cast (per cent) and at reduced cost per unit volume. These products have also been used in presplit blasting and have again achieved equivalent or better results when compared to conventional presplit blasting at a lower cost per unit volume. This product has also been used in a vibration sensitive area replacing traditional explosive products, and generating excellent fragmentation and digging whilst maintaining vibration limits. This new range of products, NOVALITE, has shown great potential in many applications either reducing cost per unit volume, improving wall quality or improving productivity in environmentally sensitive areas.

Jan 1, 2001

By Wei Han, Zhenwei Liu, Jianhong Yang, Qingwei Qin, Tiejun Chen, Zili Huang

The preparation of industrial ammonium molybdate from molybdenum concentrate was conducted according to the process of roasting—leaching—purification—precipitation—crystallization. The optimum technological conditions were determined: the roasting temperature was 680 degrees C, the roasting time was 2.5 h; in the leaching process the alkali excess coefficient was 1.2, the reaction temperature was 80 degrees C, the liquid-solid ratio was 3:1, the leaching time was 3 h; the amount of (NH4)2S added into the solution was 1.1 times of the theoretical amount, the temperature was 80-85 degrees C, and the terminal pH was 8.5-9 in the purification process; the density of the solution was 1.4-1.6 g/mL, the pH was 1.5-2 in the precipitation process; temperature of dissolution was controlled at 80-90 degrees C. The recovery of the preparation of ammonium molybdate can reach 85.18%.

Mar 1, 2017

By D Maconochie, S Pradhan, M Reed

The Waterview Connection will provide a high-quality strategic alternative to State Highway One and complete Auckland’s Western Ring Route connecting State Highways 20 and 16. The project includes twin three-lane motorway tunnels 2.4 km long and 13.1 m internal diameter (ID). The tunnel construction started in November 2013 using the tenth largest earth pressure balance (EPB) tunnel boring machine (TBM) in the world. The tunnels will pass beneath urban and greenfield areas as well as a major local arterial road. The project is being delivered by an alliance of constructors, designers and the New Zealand Transport Agency. This paper describes some of the key innovative and cost saving design solutions that have been achieved through collaboration in the alliance environment with the construction team, owner’s verifier, the segmental lining precast suballiance and the M&E suballiance for the underground works. The key design elements of the tunnel comprise a three-lane roadway, invert culvert and backfill, precast segmental lining, sixteen mined cross passages including a low point sump cross passage and steel segments for opening to the cross passages. This paper reviews interdisciplinary design integration and the economies achieved in the permanent works tunnel lining design, including reduction in lining thickness and optimising reinforcement, cross passage separation of 150 m, efficient design of the invert culvert and backfill design, main drainage pipe and low point sump. The paper also describes the attributes of the TBM and the invert culvert construction methodology.CITATION:Pradhan, S, Maconochie, D and Reed, M, 2014. Tunnel design in an alliance for Waterview Connection, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 425–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E. H. Rose

It must be evident to almost everyone by now that a massive transformation is occurring in our iron ore economy. Its equal has been seen only once before in the entire history of the North American steel industry, and not even once before within the personal memory of anyone now engaged in it. The lone precedent was the beginning of ore shipments from the Mesabi Range in October, 1892, which was before anyone still short of normal retirement age had been born. No younger observer, in the steel industry or in any other, has ever known anything else than that the Lake Superior region-in which the Mesabi is the giant-has supplied all but a small fraction of total North American blast furnace ore for the use of three generations of steelmakers. Directly or indirectly, it was the discovery of the Mesabi which created most of the prime and satellite companies that have since come to prominence in the various ore-consuming phases, and it was the same discovery that had broader effects on the entire spectrum of their technologies than any other single event that has ever happened since, although the advent of byproduct coke is a close runnerup. It affected every sector of the national economy and was a keystone in making our standard of living what it is today.

Jan 9, 1961

By Bibhu Mohanty, Sheng Huang

Accurate measure of fragment size distribution is a key objective in all blasting and crushing operations. Several generic distribution functions have been devised to describe the degree of fragmentation for the representative range of fragments from selected measurements. The application of four distribution functions, i.e. Rosin-Rammler, Swebrec, Grady and Gilvarry, in describing fragment size distribution of impact-induced fragmentation of a limestone rock has been investigated. A modified Hopkinson Pressure Bar experimental set-up is used to control both impact velocity and energy input into the target rock. The feed size in the sample holder is varied from 6.35mm to 15.88mm in three ranges and the impact velocity up to 14m/s. The size distribution in the product is determined by sieve analysis for a range of impacts. The experimental results are fitted to the four distribution functions to examine their relative accuracy and reliability.

Jan 1, 2016

Diamond drilling was first carried out at Norseman in the Princess Royal Mine, early in this century. Little concentl'ated drilling was done from then until Western Mining Corporation commenced drilling in 1934. Since then Central Norseman Gold Corporation N.L. has continually employed diamond drilling in exploration of the field. After 1946 the advantage was seen of applying broad pattern surface drilling at Norseman in the reef exploration. In 1953, as a result of the steeply rising cost of drilling and the time taken to penetrate surface material by light equipment, heavier drills and new rigs were introduced. The surface drilling programmes called for a greater monthly or annual footage and to satisfy this new techniques were introduced. The Mitchell-21 machines were discarded and A-3000 machines were installed, firstly under a 48 ft. fixed tower, then mounted on a truck with a 20 ft. tower, and finally on a truck carrying a 40 ft. tower. With the mobile units a compressed air compressor is attached. By use of compressed air with either the Reed roller or Hawthorne bit, rate of penetration of overburden is greatly increased. The mobility of the truck mounted machines has greatly reduced the time required to move from one hole to another, and the use of heavier machines on a three shift per day basis has considerably increased the footage per shift. The general result is an increase to 1,500 ft. of drilling per month per machine, while costs have been greatly reduced in spite of increased wages and diamond prices.The underground drilling technique is described. Analysis of performance has not been made because the drillers performance is subject to shaft routine and service.INTRODUCTIONGold was first discovered at Dundas in 1894, and at Norseman, 14 miles north, in 1895. From that tirpe until 1935 mining activity fluctuated. Following the mining revival in 1935, production in the field has remained comparatively stable. This stability in part has been due to the broader scale of operations of Central Norseman Gold Corporation N.L., and in these operations diamond drilling has played an increasingly important role.

Jan 1, 1956

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

Jan 1, 1912

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By François Robichaud

"The Laronde mill has been in operation since 1988. Actual milling rate ranges from 7,000 to 8,500 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails.In 1999, the carbon in pulp circuit was replaced by a Merrill-Crowe circuit in order to cope with a much higher ratio of silver/gold associated with the discovery of the Penna shaft. Marine type diatomaceous earth was used as filter aid in both clarifier pressure leaf filters and recessed pressure filter presses from 1999 to 2005. In 2005, this filter aid was gradually replaced by alpha-cellulose after several laboratory and plant filtration trials. The selected cellulose is considered to be much less sensitive to parameters such as pH and reagent concentration and have increased clarifier and filter press filtration performance. Also, since cellulose is exothermic, replacing diatomaceous earth with cellulose as filter aid in the filter presses has increased calcining and oxidation rates in the calcining ovens since cellulose is exothermic. Finally, better calcining conditions have resulted in energy and reagent savings at the arc furnaces.This paper describes how the filter aid replacement has contributed to increasing productivity and Net Smelter Return of the refinery while reducing worker’s hazards and operating cost.INTRODUCTIONAll Merrill-Crowe circuits in the world are operated with filter aids. For years, the market for precoat filter aid has been dominated by mineral filter aids such as diatomite and perlite. Flowsheet and equipment selection at the Laronde refinery were performed in the late nineties. At that time, some key parameters of the design criteria had clearly identified marine type diatomaceous earth (DE) as the most successful filter aid. Parameters such as reagent cost and availability, clarity of the filtrate solution and good historical filtration performance in other concentrators had designated DE as the best suited filter aid. Pregnant solution processed in the refinery from its start-up through 2001 was fairly stable in flow rate and reasonable in terms of impurity content (cationic and anionic compounds)."

Jan 1, 2007

By Samantha Whisman, James R. Hein

Hydrothermal marine manganese-oxide deposits (HMMD) are cemented and variously replaced volcaniclastic and biogenic sediments that were mineralized by distal, low- temperature, hydrothermal fluids. HMMD predominantly form below the seabed as sediment-hosted statabound deposits but can also form on the seabed. These deposits form at oceanic and back-arc basin spreading centers, volcanic arcs, and mid-place hotspot volcanoes. HMMD have traditionally not been considered to have an economic potential because they were considered to be devoid of economically valuable critical elements. This contrasts with their non-hydrothermal counterparts, ferromanganese crusts and nodules, which are enriched in many critical elements. However, manganese is now one of the critical metals and HMMD have the highest manganese contents (up to 55% Mn, so- called battery-grade Mn) of all the types of deep-ocean mineral deposits. There is a growing demand for this critical metal and an upward trend exists in the price of manganese on the global market. Also, other critical elements can occur in high concentrations in some HMMD and their economic potential has not been considered, especially for lithium (up to 0.17%) and molybdenum (up to 0.24%), but also vanadium (to 820 ppm), chromium (to 346 ppm), and nickel (to 0.45%), among others. Which of these critical elements are enriched and their concentrations depend on the types of rocks leached at depth by the hydrothermal fluids, the composition of hydrothermal minerals precipitated in the higher temperature parts of the circulation system, and the types of sediments mineralized by the manganese oxides. For example, mineralization of a carbonate sediment resulted in the highest lithium contents, whereas leaching of ultramafic rocks at depth as a rule results in the highest chromium and nickel contents in the HMMD. These deposits are known to be widespread, especially in volcanic arcs, but their lateral and vertical extents and consequently size, tonnage, and grade have not been determined. Most samples of hydrothermal deposits have been collected by dredging and therefore the in situ relationships often are not known. One sample from the Mariana volcanic arc, west Pacific, was collected by ROV at 1274 m water depth from a layered outcrop 6.6 m thick that may be a sequence of pervasively mineralized volcaniclastic layers and offers the first clue as to the potential vertical extent that these deposits may attain. However, only the top ~0.4 m-thick layer was sampled, so it is not known whether the mineralization extents throughout the outcrop. Although large manganese deposits of various origins occur on the continents, they consist of manganese carbonates, silicates, or complex mixtures of manganese minerals. In contrast, marine hydrothermal HMMD exhibit relatively simple mineralogy that would make processing of this potential ore much simpler.

Jan 1, 2018

By William G. Pariseau

Safety of mine ramps begins with an analysis of stress that almost certainly must be done numerically to take into account ramp geometry, route geology, rock properties, and pre-ramp stresses. The popular finite element method serves analysis purposes quite well. As a practical matter several obstacles to implementation need to be addressed including collection of rock and joint properties along the proposed ramp route, selection of ramp type, and specification of cross-section shape, size, and route grade. Additionally, stresses along the proposed route must be specified, preferably from in situ measurements. One need not be an expert in numerical methods to proceed to ramp design, although a background in mechanics of materials and rock mechanics is essential, and a first course in numerical methods is quite helpful. The necessary software is easily brought to the design task, more accurately, to the task of design evaluation. This software also addresses other important mine design problems including design of safe (1) main entries in stratified ground, (2) barrier pillars, (3) bleeder entries, (4) inter-panel barrier pillars, (5) room and pillar mines, (6) shafts, and (7) “tunnels” (Pariseau 2022).

Feb 1, 2024