Search Documents

By Samuel Filgueiras Rodrigues

An austenitic stainless steel ISO 5832-9 was deformed in a torsion test machine over the temperature range of 1,000°C – 1,200°C and strain rates of 0.05, 0.1, 1.0 and 5.0s-1. The Steel plastic behavior was studied by analyzing the flow curves shapes and using the constitutive equations under the conditions of thermomechanical treatment. The curves initially presented an increase in stress characterized by hardening work, followed by a drop in stress to an intermediate level that reached or not, for certain conditions, the steady state softening. The plastic flow curves of ISO 5832-9 steel displayed in three different ways: (i) Curves with continuous softening presenting plastic instability for low temperatures and high strain rates; (ii) curves type flat, here after the peak there is little variation of stress with strain presenting softening mechanism by higher contribution of dynamic recovery at low temperatures and low and intermediate strain rates; (iii) curves with softening after the critical deformation favored by high temperatures and low strain rates. These behaviors indicate the influence of the stacking fault energy (SFE) and precipitated particles on the softening kinetics of this steel.

Aug 8, 2018

By José Maria Silva, Eugênio Oliveira, Ruberlan Silva, Thiago Souza, Lucas Reis, Lorena Guimarães, Matheus Bianchetti

Copper mine operations consistently generate a large quantity of tailings after their concentration processing. These tailings are either piled up or stored in a dam, where both alternatives of disposal lead to environmental impacts. The dam copper tailings have a huge potential for by-product production thus improving sustainability and profitability in industrial operations. This paper describes a study aiming at producing a magnetite pellet feed as a by-product from a dam chalcopyrite flotation tailings and generating free magnetite non-magnetic rougher tailings. The chemical assay and mineralogy analysis of dam copper flotation tailings indicate low Fe grade (6.34 wt%), high SiO2 grade (63.14 wt%), low magnetite (3.6 wt%), and high iron silicates content (22.72 wt%). The complex mineralogy of these tailings leads to the need of grinding the rougher magnetite pellet feed as fine as 80% of particles smaller than 20 μm ( P80) aiming at improving magnetite liberation. The proposed process route comprises a scalping screen, low field rougher, and cleaner magnetic separations using a drum magnetic separator (80 kA/m or 1000 Gauss), followed by silicates reverse cationic flotation as a recleaner step. With this process route, it was possible to produce a high-quality magnetite pellet feed reaching 68.00 wt% of Fe, 2.13 wt% of SiO2, 0.51 wt% of Al2O3, and 95.1 wt% of magnetite. The Blaine specific surface area was 2300 cm2/ g, being in the range recommended for pelletizing (1900 up to 3000 cm2/ g). The total mass, Fe, SiO2, Al2O3, and magnetite recoveries were 2.77%, 29.71%, 0.09%, 0.12%, and 73.17%, respectively. Most of the magnetite losses, around 20% of total magnetite fed, occurred in the oversize of the scalping screen. Additionally, it generated non-magnetic rougher tailings with less than 1.0 wt% of magnetite that could be used as by-products and reduced the amount of tailings disposal in a dam. This study contributes toward the sustainability of operation, minimizing tailings disposal.

Sep 28, 2022

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951

By G. Bonifazi

The study of minero-petrographical characteristics and the subsequent textural and structural characterization of an ore mineral represents the first step of each industrial processing whose aim is the beneficiation of each valuable mineral phase present inside the ore. Analytical, mineralogical and petrographical, chemical and multispectral image analyses based investigations, applied to eclogitic ore samples deriving form "in situ" sampling campaigns, were applied. These procedures enabled to point out some textural and structural aspects characteristics of ore litotypes belonging to eclogitic-amphibolitic dikes. Such dikes are characterized by a paragenesis constituted mainly by siliceous gangue and accessory "useful titanium minerals" as rutile [TiO2], "pseudolilmenite", ilmenite [FeTiO3] and sphene [CaTiSiO5]. In the beneficiation process applied to ore s is of preliminary importance to establish a strategy in order to obtain a recovery of high quality "mono-minerals concentrates" as rutile, "pseudolimenite", ilmenite and phene. To reach this goal is thus necessary to develop a preliminary study of the textural, structural, petrochemical and minerochemical characteristics of the samples. Different ore samples (eclogitic rocks), resulting from sampling campaigns carried out in the Piampaludo area (Sassello district: Savona, Northern Italy), are examined.

Jan 1, 1994

By Jianmin Qin, R. V. Ramani

The major parameters affecting dust flow at a longwall face are dust generation rate, air velocity and quantity distribution at the face, and the characteristics of the dust such as particle size distribution, density etc. Previous studies have identified the longwall shearer as the major source of the airborne dust in the faces. In this study, the effects of dust generation rate and shearer speed on the levels of ambient dust concentration are investigated. A series of experiments were performed under controlled conditions in a full scale simulated longwall face at the Lake Lynn Laboratory mine of U.S. Bureau of Mines using characterized bituminous coal dust. A trickle-duster was moved up and down the longwall face to simulate the shearer. In each experiment, a known amount of dust was dispersed by the trickle-duster into the air and the average dust generation rate was calculated. At the same time, gravimetric respirable and total airborne dust samples were collected and air velocity measurements were made along the face. The experimental conditions, data, and results are presented and discussed in this paper. The airborne dust concentration and air velocity data indicate that the concentration increases and air velocity decreases with distance from headgate for the first half of the face. Towards the tailgate, the air velocity increases with increasing distance but the dust concentration levels off with some variations. The data show that a higher dust generation rate results in higher dust concentration levels. More importantly, the data show that the rate of increase of airborne dust concentration is higher than that of dust generation rate. For the same air velocity distribution and dust generation rate, lower speed of the dust source results in higher airborne dust levels at the face.

Jan 1, 1991

By W. Keith Buck

Introduction During World War II years, the magnetometer was used by various field parties of the Geological Survey of Canada, specifically in the search for chromite, a strategic war mineral. Throughout the summer of 1944, Professor J. W. Ambrose used the instrument experimentally on eight separate projects (1). Since then, several members of the Survey have come to consider its use to be of valuable assistance in the season's mapping. Dr. C. H. Stockwell, in particular, regards use of the magnetometer as a necessary part of detailed geological survey work. Throughout the field season of 1949, the magnetometer was used by Dr. Stockwell?s party as an aid to mapping in detail, to the scale one thousand feet to the inch, the south-west quarter of Dasserat township, Temiskaming county, Quebec. The principal geophysical project that was undertaken was the location of the Horne Creek fault and the Diabase fault in the area approximately midway between Arntfield and Kearns, on the Quebec side of the Interprovincial border. The location of these faults on either side of this central area was known. The Horne Creek fault is a subsidiary fault to the Cadillac 'break' which extends ?westward from Val d'Or through Cadillac to beyond Larder Lake. It lies to the north of that major fault zone and has a general southwesterly trend.

Jan 1, 1951

By Wenjun Duan, Kun Wang, Qingbo Yu, Qin Qin

"A novel oxygen production technology noted chemical looping air separation (CLAS) was introduced and properties of Cu-based oxygen carriers used were investigated. The oxygen carriers were prepared by mechanical mixing. Al2O3, Fe2O3, ZrO2, TiO2 and SiO2 were used as binders during the preparation. XRD patterns show that spine! oxides are formed using Al2O3 and Fe2O3 as binders. Phases of CuO and binders keep stable using ZrO2, TiO2 and SiO2 as binders. BET values of oxygen carriers increase in the order of ZrO2>TiO2>SiO2>Fe2O3>Al2O3. The effects of temperatures, binders, particle sizes and flow rates on reduction/oxidation reaction rates were studied in TG experiments. The reduction reaction rate increases in the order of ZrO2>TiO2>SiO2. The effect of binders on the reactivity of oxidation is not obvious. The reduction and oxidation reaction rates both have the tendencies of increasing with the temperature increasing and with gas flow decreasing. However, the effects of gas flow and particle size are little.IntroductionChemical looping air separation (CLAS) is a novel oxygen production technology. The oxygen carriers used in CLAS release oxygen in reduction reactor and regenerate in the oxidation reactor. Selecting suitable oxygen carriers is the key for CLAS. Oxides of CuO, Mn2O3, Co3O4, Pb3O4, CrO2, SrO2, PdO2 and CeO2 have the property of releasing oxygen at suitable temperature and oxygen partial pressure [1]. Among these oxides, CuO, Mn2O3, Co3O4 are the most common compositions used to prepared oxygen carriers for chemical looping combustion (CLC) or chemical looping with oxygen uncoupling (CLOU) [2-5]. Moreover, thermodynamic calculations and preliminary experiments were carried out on oxides of Cu (CuO/Cu2O), Mn (Mn2O3/Mn3O4) and Co (Co3OJCoO) by Moghtaderi to ascertain their feasibility for CLAS process [6]. CuO has the highest oxygen transport capacity (0.1 g 02/g CuO compared to 0.03 g 02/g Mn2O3 and 0.06 g 02/g Co3O4). However, agglomeration is the biggest issue for copper oxides used at high temperature because of its low melting point (l 450°C for CuO, 1235°C for Cu2O and 1075°C for the mixture of CuO and Cu2O) [7]. In order to improve the capability of anti-sintering and stability ofCuO, binders (ZrO2, MgAl2O4, TiO2, SiO2, Fe2O3, Al2O3, cement) are added during the preparation of Cu-based oxygen carriers [8]. In this paper, the Cu-based oxygen carriers were prepared by mechanical mixing method. TiO2, Al2O3, Fe2O3, ZrO2 and SiO2 were selected as binder. XRD, BET and SEM were used to analyze the phase, surface area and surface morphology of oxygen carrier prepared. The reactivity of oxygen reduction and oxidation of oxygen carriers prepared were investigated in STA409PC thermal analyzer."

Jan 1, 2014

By Robert Hunt

ONE of the most serious and important economic administrative problems facing American railway authorities to-day is that of their rails, and it is one to which much thought, is being given, not only by the executive officers of the railways and the manufacturers of the steel rails, but also by State and National commissions. It is realized by many and admitted by some that the present situation is one which cannot continue. The roadways of railways must be made more secure, or the weight of rolling stock and the speed of trains must be lessened; and the desired result must be attained with the minimum outlay of money, both in expenditure on plant and in cost of operation. If the investment per mile is too large, or through the lessening of tonnage and efficiency of equipment the cost of operation is too great, the desired and demanded cheap service cannot he rendered to the public. Therefore, the weight of equipment cannot be greatly reduced, and lessening the rapidity of service would be far from satisfactory; consequently, the safety of the roadway must be secured with the least practical outlay. It is imperative that the roadbed should be properly graded, with the fewest practically possible curves; that it should have good ballast, be well drained, have good ties properly spaced, and be laid with sound rails of suitable weight, efficiently joined together, and that the whole property be carefully and intelligently cared for. My province is to treat of the sound rails. During the last few years there has been renewed interest in and discussion of that question, and I know that many rail makers not only have been and are desirous of maintaining the highest standards of manufacture which they may have attained, but have been and are seeking to better their product, in several instances devoting much time and money to that end. At the same time, they realize that the cost of any improvement in quality which they may accomplish must be kept within certain commercial bounds; and that fact is as fully understood by their patrons as by themselves, and it should be kept in mind by all who discuss the question.

Jan 2, 1914

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

De la pirotechnia. Libri .X. dove ampiamente si tratta non solo di ogni sorte & diuersita di miniere, ma anchora panto si ricerca intorno á la prattica di quelle cose di quel the si appartiene á l'arte de la fusion ouer gitto de metalli come d'ogni altra cosa simile I questa. Composti per it S. Vanoccio Biringuccio]

Jan 1, 1942

By Robert F. Droullard

The U. S. Bureau of Mines (USBM) has investigated instrumentation and methods for measuring exposure to radon daughters in underground mine atmospheres. Both personal and area monitors have been studied through in-house and contract research. A field study in uranium mines identified some reliability problems that required additional work for the personal dosimeter systems. Improved versions of continuous working level detectors have been developed and tested for use as area monitors in underground mines. Test results for the personal and area monitors were satisfactory for underground mine applications.

Jan 1, 1981

By Ruirui Wei, Mingrui Yang, Xuewei Lv

Copper slag is a by-product obtained during smelting of copper from copper ores. In China, for one ton of metal production about 2.2 tons of copper slag was generated, and approximately 15 million tons slag is produced in 2013. Dumping and disposal of such huge quantities of slag will cause environmental and space problems. Most importantly, copper slag cannot be made full use of to maximize its value. In this study, copper slag was used to take the place of scrap iron and part of silica in traditional process and to produce FeSi alloy as the main material. Utilizing silica and copper slag as the raw materials and coke as the reducing agent, FeSi45 was produced in the induction furnace. In addition, the effect of different n(C)/n(O) on FeSi45 has been investigated.Increasing n(C)/n(O) is beneficial to form the stable phase of FeSi. Meanwhile, n(C)/n(O) greatly affects the reduction and recovery of silicon than iron. When n(C)/n(O) equals 1.10, the recovery of silicon and iron is about 77 and 95%, respectively.

Mar 1, 2017

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

"In response to mine head grades declining and orebodies becoming more complex, Glencore Technology has developed an alternative method for recovering economic minerals once leached into solution, rather than relying on conventional flowsheet options. The method involves the precipitation and separation of base metals from solution with limestone or lime. The final grade of these precipitate is not usually high enough to attract favourable terms of sale due to dilution from gypsum and sulphate salts. A set of operating conditions have been developed to allow the separation of the base metal precipitate from gypsum by exploiting the difference in particle size. A high-grade oxide product can be easily separated from the gypsum stream at very low cost. This process was originally developed by Glencore for zinc and copper systems. This paper reports on the successful application to nickel and cobalt, and this process has significant advantages over the incumbent precipitation process utilising magnesia.INTRODUCTION During evaluation of transitional and oxide zinc ore deposits during the 1990’s, Noranda Inc. (now Glencore) developed a sulphate based ore leach process to extract zinc into solution. For flowsheet development, conventional schemes dictated that once the zinc was dissolved in an acidified solution it was recovered by means of purification or solvent extraction followed by electrowinning and casting to produce zinc ingots. The deposits Noranda evaluated were high grade but had a relatively short mine life (10 years) and economic analysis showed that the projects couldn’t sustain the investment of a full zinc refinery. Compounding this problem was the lack of power supply infrastructure and the high power cost in the region. Noranda then evaluated alternative means of recovering zinc from solution. Laboratory testwork showed that a high-grade zinc precipitate (+50 wt% Zn) could be produced as an oxide, carbonate or sulphide by contacting acidified zinc sulphate solution with a number of reagents including soda ash, sodium hydroxide, and sodium hydrogen sulphide. Economic evaluation showed that the cost of the reagents are prohibitive, especially when the final product is still a metal intermediate (ZnO, ZnCO3 or ZnS). Noranda then continued to focus on fine zinc oxide precipitation for supply into the automotive tyre industry as this product would attract favourable terms of sale as a premium on Special High Grade (SHG) zinc."

Jan 1, 2017

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, and the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following six years. To understand how this historic goal was achieved, this study analyzed hundreds of roof fall fatality reports covering five decades. It found that the immediate effect of the Federal Coal Mine Health and Safety Act of 1969 (Coal Act) was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, fostered the necessary improvements in both the safety culture and the mining technology.

Jun 1, 2024

By W. L. Saunders

THE world's greatest producing area is, geographically, in the midland region of North America about the Great Lakes. This area, with but one- third of the nation's population, produces, with the exception of tobacco and cotton, three-quarters of the principal staples. It provides the surplus or export grain, meats, dairy products, steel and leading minerals. The social and political condition of a nation is determined by its industrial efficiency, and the share of the commerce of the world obtained by a nation is fixed more by the economy of its transportation than by any other factor. It is an economic maxim that: The total cost is the cost of production plus transportation cost. The cost of carrying 1000 tons by water or 100 tons by rail is equal, over the same distance

Jan 1, 1921

By Ruilin Yang

Kinematic approach of blast modeling refers to using the velocity, strain, or displacement as controlling parameters to model blasting, rather than the stress and the material constitutive relations. The rock stiffness or constitutive relations is very hard or impossible to obtain due to the complexity of the rock mass property.

Feb 1, 2020

By C I. Edwards

Phosphorous is typically present in iron ore either in the mineral apatite, Ca5(PO4)3OH, or associated with the goethitic fraction of the ore. In this paper, we present results that show that phosphorous associated with the goethitic fraction can be removed with a heating pretreatment around 300 176;C for 1 h, followed by a caustic leach with 1 - 5 M NaOH, or a leach with sulfuric acid at pH 0.5. The heating pretreatment is considered to dehydroxylate the goethite to form a haematite intermediate phase, ‘protohaematite’, that reacts during the leach making the phosphorous accessible to the leachant. In the acid leach, ten to 15 per cent of the sample was dissolved to obtain a leach product with 0.08 per cent P. In the caustic leach, as no weight loss occurs, it is proposed that iron species associated with the protohaematite have either not dissolved or have reprecipitated at the high pH values of the leach.For an ore containing apatite as the source of phosphorous, a leach with sulfuric acid dissolved the apatite, lowering the phosphorous levels in the sample. The sample treated contained carbonate minerals (including siderite) that also reacted with the acid, and in practice a balance between the dissolution of the apatite and the carbonate minerals may be needed to minimise acid consumption.

Jul 11, 2011