Search Documents

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By J. Kronsteiner, E. Kabliman

"In the present work, we developed a Smart Process Control Toolkit (SProC) as a single simulation environment for the modelling of materials microstructure and its interaction with the local microchemistry during manufacturing of semi-finished products. This toolkit supports the data communication between sub-sequent processing steps such as casting, homogenization, pre-heating to deformation, etc. The thermo-kinetical simulation software MatCalc of MatCalc Engineering© GmbH was used for modelling of precipitation kinetics, such as formation of primary and secondary phases and their evolution. An import/export functionality of the precipitation distribution after each processing step was implemented to follow the parameter history. For the evolution of the local microstructure, a Mean Dislocation Density based Model (MD2M) was used. This model consists of two parts: (1) Flow Stress Model for calculation of the total strength during the deformation and (2) Static Recrystallization Model for account of the recrystallization and grain growth after the deformation. Validation was done by a comparison of experimental and simulated hot compression tests of a conventional AA2024 alloy.INTRODUCTION Optimization of a semi-finished products quality, elimination of typical production issues and cost savings are of a great demand for supply industries. However, it is currently not feasible to investigate the whole manufacturing process in detail at an industrial level. Concerning the processing parameters, one must understand the correlation mechanisms between macroscopic properties and microscopic material behavior. Numerical simulations, which could reproduce the real processing conditions on the one hand, and employ a physically based modelling on the other, are thus attracting a lot of attention and their power is no longer under the question. It is well known that e.g. the total strength of the material depends directly on distribution of precipitation particles and mean grain size. In order to follow their evolution during the manufacturing process beginning from casting to the final semi-finished product, and thus be able to control the process, one should use the techniques which would at the same time reproduce experimental processing conditions of real size objects (e.g. sheet, extrusions, etc.) and account for the evolution of a local microstructure and its interaction with the microchemistry. A commonly used approach is to implement a model which would describe the evolution of microstructure based on a dislocation density approach into a user defined material subroutine of some finite element solver. There is, however, also an influence of the manufacturing process by e.g. the evolution of a local microchemistry (formation, transformation and dissolution of the precipitation particles) on the microstructure and thus the macroscopic material behavior. Thus, a method is needed to follow the variable history through the simulation of the whole production chain."

Jan 1, 2018

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By M Ewart

The securing of a reliable water supply for a prospective mine in the North West Queensland Mineral Province is usually one of the most influential factors in determining the mine's feasibility. The Ernest Henry Mine required a reliable water supply to serve a demand estimated at feasibility stage to be up to 20 ML/day. Numerous options were considered before a decision was made to construct a 113 km long pipeline from Lake Julius as this was the most cost effective, reliable source of supply. The North West Queensland Water Pipeline is a multi-user, Queensland government funded project initially supplying up to 7000 ML/year of water from Lake Julius to Ernest Henry Mine, with provision made for expansion to serve future users in the region. This paper discusses the history of the pipelineÆs development, together with a summary of the scheme's design features. Environmental and licensing requirements, construction and operational issues are also discussed.

Jan 1, 1998

By L. E. Porter, H. P. Hassel

The state of California produced 310,-996,696 bbl. of oil and about 415,832,000 M cu. ft. of gas in 1944. Such oil production represented 18.5 per cent of the nation's production, as compared with 19 per cent in 1943 ,The tremendous demand placed upon the California fields is indicated by the monthly production in 1944, as follows: Month Barrels per Day Jan................... 809,262 Feb.................. 820,712 Mar.................. 824,592 .4pr ................. 829,973 May.................. 832,068 June.................. 846,038 July.................. 849,231 Aug.................. 858,932 Sept.................. 885,823 Oct................... 877,667 Nov.................. 876,613 Dec.................. 883,847 In all, 2100 wells in proved areas and 269 wildcats were drilled in California during the year 1944. At the end of the year, approximately 270 wells were drilling in the state, as compared with 156 wells at the same time in the preceding year. Nine new fields or new zone discoveries were made during the year, which, according to best estimates, will contribute some 77,000,000 bbl. of new reserves; in addition, the extensions of old fields will increase the new reserves about 165,000,000 bbl., or a combined total, through dis- coveries of new fields, zones, and extensions, of 242,000,000 bbl., offsetting to the extent of about 78 per cent the total oil produced during the year. Geographically, the reserves from these new field and zone discoveries and extensions are distributed as follows: Per Cent San Joaquin Valley........ 72 Coast Area............... 24 Los Angeles Basin Fields. . . 4 100 The state's reserves of crude oil at the end of the year have been estimated to be distributed as follows: The outstanding development project for the year was that of the United States Navy in the Naval Petroleum Reserve No. I, Elk Hills field. During the year, 115 wells were completed in this field, and at the close of the year an average of 19 strings of tools were drilling. This program is being jointly conducted by the Standard Oil Co. of California with the Navy and is designed to increase the production of Naval Petroleum Reserves from approxi-

Jan 1, 1945

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999

By K. Purazrang, P. Sh. Naseri, P. Abachi

In present work, the comparative measurement of aluminum alloys' resistance to the unstable fracture was provided. Besides, the rupture mechanisms of high strength 7075 and 7050 aluminum alloys were investigated. The specimens were used as solution treated, quenched and aged condition. The elastic-plastic behavior of specimens was determined by carrying out tensile test on cylindrical specimens. The small sized specimen with 6.35 mm thickness and V-notched radius less than 60 µm was used for evaluation of damage properties, in accordance with ASTM B871-96 standard test method. All tear specimens were machined in L-T orientation. The mechanical tests were conducted at RT on an universal Instron machine under cross head speed of 0.1 mm/min. The results of mechanical tests made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. The comparison of specimens' resistance to crack propagation and unstable fracture due to the presence of crack-like strain concentrator was provided using tear test data. The microstructure of specimens was studied under optical microscopy. The rupture micro-mechanisms were analyzed by examination of specimens fracture surfaces using SEM. The microstructure examination indicated almost equiaxed grains on the transverse directions and elongated grains on rolling direction. Moreover, intermetallic particles were evident at microstructure. Considering the SEM fractographs, it seems that the intermetallic particles act as void nucleation and damage initiation sites. However, the damage mechanism of tensile specimens and severely notched specimens, especially near the notched root differs due to stress and strain states.

Jan 1, 2006

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By R. P. Walters, M. J. Lynch, D. R. Flinn

The Bureau of Mines evaluated tthhee feasibility of substituting platinum- coated metals for bulk platinum shapes as a means for conserving platinum . Platinum coatings were prepared using four different methods of electrodeposition , then tested and evaluated . In order for platinum coatings to be useful in process environments , they must be thick , adherent , stress - free , and pore - free . The Bureau evaluated direct - current , current reversal , cathode shielding , and pulsed- current plating techniques for producing a pore-free platinum electrodeposit from a molten cyanide bath . Aqueous corrosion tests of Fe - 10Cr substrates coated with approximately 25 μm of platinum showed that pulse plating yielded the most corrosion- resistant and , hence , the most pore -free coatings . The morphology of coating cross sections was in all cases columnar . The average grain size of pulse -plated deposits was independent of thickness , while all other plating techniques produced grains that increased in size as the coatings became thicker . It is believed that the constant grain size in the pulse - plated deposits resulted from better mass transport during the electrodeposition .

Jan 1, 1965

By C. A. Stetefeldt

The purpose of this paper is to convince the managers of silvermills that their customary reports in regard to the percentage of silver saved are far from the truth. It may be unpleasant for them to have the proofs of this fact brought before the public, and for this rezson the author refrains from giving the names of the mines and mills from which the statistics here recorded were obtained. It may be asked: What is gained by informing the stockholders of our silver-mines that they receive incorrect reports? Will this increase their dividends or lessen their assessments? In the first place, it is always better to publish honest facts than fiction. In the second place, many superintendents believe in the correctness of their reports, and have no idea how much they deceive themselves. Finally, the knowledge that hitherto unexpected losses of silver take place may lead to the adoption of methods by which these losses are greatly reduced. These remarks refer also to smelting-works. The present paper, however, is concerned exclusively with amalgamation and lixiviation. The first and most important error is found in the inaccuracy of the commercial assay; the second in the incorrect sampling of tailings in amalgamation. Further, mills not doing custom-work, but reducing exclusively ores from mines to which the mills belong, are in the habit of weighing the ore only approximately and without making moisture-tests. Thus, a correct basis for calculating the actual percentage of silver extracted is lacking. The superintendent, then, finds it convenient to report the apparent extraction, i.e., the extraction indicated by comparing the value of the roasted ore, minus soluble salts, with the value of the tailings. How many errors are thereby committed it is not necessary to point out.

Jan 1, 1895

By S Coughlan

"A personal account of my journey from a student from suburban Melbourne in the 1970s through 40 odd years in and around the mining industry including the important events that have moulded my thinking and, as result, have formed the guiding principles of the mining contracting business and related entities that make up the Byrnecut Group. On reflection the game of chance has played a big part in the journey, from the selection of initial study based on my parents financial capability and the one and only offer of early employment by Western Mining Corporation where the formative phase of my career took place in what was the vibrant can do environment that existed in Kambalda in the 1970s and early 1980s. Subsequently the unplanned meeting with Frank Lubbock drawing me back to Kalgoorlie from Fiji in 1987 and the resultant formation of a private mining contracting business, the excitement of the mid 1980s Kalgoorlie mining environment followed by the turmoil of the 1987 stock market crash where business survival was the game, resulting in a relationship with the German based Thyssen Group.Thereafter the development of a large privately owned international multifaceted mining services group and the principles behind that growth. These include: development of strategic personnel and retention of those personnel cashflow management and debt within a private company scenario recognising opportunity for synergetic growth but insisting on market forces driving those business elements, as opposed to internal divisions group-wide sustainable business systems, particularly in relation to leading safety and training processes innovation and renewal to provide the elusive advantage in a competitive market the role of entrepreneurial small businesses in development of technology.The above principles combine to make a margin in a cut throat contracting environment, competing on the world stage against other contractors and owner mining options.CITATION:Coughlan, S, 2014. A miner’s journey, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By Gary L. Hundley

As part of the U.S. Bureau of Mines program to reduce the Nation's reliance on foreign supplies for critical metals, a procedure was devised to separate and recover critical metals from mixed and contaminated super alloy scrap. The process uses both pyrometallurgical and hydrometallurgical methods to treat the scrap. The mixed scrap is converted to a matte containing 4 to 7 pct S by adding S directly to the molten metal. This matte is then granulated and ground to a minus 35-mesh particle size and leached with an HCI-CI2 solution. This process takes essentially all the Ni, Co, Cr, Fe, AI, and Mo into solution in a 3-h leach, leaving W, Ta, Ti, and Nb (Cb) in the residue. The Mo is recovered from the chloride leach solution by solvent extraction, and the Cr and Fe are recovered together by precipitation. The Ni and Co can be recovered individually by an existing solvent extraction-electrowinning process. The W is recovered by a caustic leach of oxidized Cl2 leach residue.

Jan 1, 2010

By Sanaz Mosadeghsedghi

The feasibility of the application of electrodialysis in separation of light and heavy rare earth elements (REE) in synthetic solutions was investigated. The experiments were carried out using single and binary solutions of a light (cerium) and heavy (ytterbium) REE. The effects of electrical voltage, electrical current, and the addition of complexing agent (EDTA) to increase the separation selectivity were investigated. Separation of Ce and Yb was achieved in binary solutions with and without the addition of EDTA. Higher degrees of separation were seen at higher voltages. Ce–Yb separation was more significant in the presence of EDTA. The separation factor of Ce–Yb and Ce–Yb-EDTA were 1.44 and 2.60, respectively.

By R. W. Thompkins

In order to evaluate the impact of air quality control on mine design, a few examples are given of cases in wh.ich ventilation has affected the economics of the total design problem. Principles for the drainage of gas contaminants are shown, and the contamination control problems created by differential pressures in complicated booster fan installations are discussed. The paper also deals with the use of advanced mathematics for solving some of the ventilation problems likely to be encountered.

Jan 1, 1967

By L. B. Lindemuth

To those who are in a position to carry the thought to a conclusion; I would like to present a theory for the cause of blisters in galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered because the reason for their formation is entirely obvious. Blisters that occur periodically with no apparent system of ocation, number, size or grouping, and then disappear with no. apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pressure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or washing and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening where it entered as moisture.The pressure so generated forces the sheet apart along those lines of lamination ;hat may be found in practically all flat sections of steel rolled comparatively cold. The increase in volume. from moisture to steam at 800° F. is 2244 times the original volume of the moisture. The pressure generated by ;he moisture heated to 800° F. and entirely confined would be enough to expand or explode any container. This would explain the source of sufficient pressure to cause a sheet to blister.

Jan 3, 1927

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015