Search Documents

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

A borehole sonde using a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed. With the sonde stationary at points above, in, and below the coal bed, capture gamma rays were measured to show the variation in concentration of certain elements. From the spectrum recorded in the bed, a complete ultimate analysis, the percent ash content, and the heat content were determined without recourse to an external standard. Delayed gamma-ray analyses of the core were also made on the surface in the vicinity of the borehole in a fixed-geometry irradiation facility wing the detector in the borehole sonde. The concentrations of 10 elements were determined by this method on a coal split from the drill core. These experiments show that it is feasible to use a 252Cf- Ge(Li) borehole sonde as an aid in coal exploration.

Jan 1, 1979

By Thomas H. Hibner, Daniel Tempelis, John E. Shamma

Environmental protection of nearby resources is an issue that can not be ignored in tunnel construction. The Inland Feeder Arrowhead Tunnels Project is no exception. With keen interest from various stakeholders, Metropolitan developed a Groundwater Monitoring and Mitigation Plan. This plan provides for monitoring and management of selected water resource features within the San Bernardino National Forest along the proposed tunnel alignment. The plan specifically provides for monitoring of streams, springs, seeps, and piezometers for water temperature, pH, specific conductance, and chemical analyses, as well as flow or groundwater elevation. Metropolitan uses the data to evaluate for and manage potential impacts from groundwater ingress during construction of the Arrowhead Tunnels.

Jan 1, 2003

By P. R. Taylor, B. N. Carlson

Rare earth magnets play an increasingly important role in high end technology, and the manufacture of rare earth magnets, such as the NdFeB type, consume a large amount of the rare earths produced. Recycling of this material could provide an important domestic source for these materials. A selective sulfation roast has been proposed; the central principle of which is to take advantage of the differing stabilities of the rare earth sulfates as compared to those of iron under an air/SO2 atmosphere. Experiments show iron is found to be stable as an oxide, however, neodymium is found to form an oxy-sulfate phase.

Mar 1, 2017

By Lu Jun

Up to now, much data on marine minerals, as well as on marine geochemistry, have been accumulated. Modem computer databases provide optimum flexibility and power for manipulating these data. The best worldwide marine mineral database is currently the Marine Minerals Bibliography and Geochemical Data Base created by Carla Moore et al. at the National Geophysical Data Center in the United States. In fact, in the course of studying marine minerals and geochemistry we may collect not only digital-character type data but also graph and image (black-white, grey and color image) data types. For instance, correlation diagram between chemical compositions of minerals, spectroscopic graphs, (e.g. infrared spectra, Mossbauer spectra, etc.), grey or color images from both optical and electron micro- scopes (scanning or transmission electron microscopes) as well as seabed photographs. Charles L. Morgan et al. (1993) reported that 10,000 photographs and some video images of the seabed in the Clarion-Clipperton region of the northeastern tropical Pacific have been collected by the Ocean Minerals Company. If both graphic and analytical information were stored in a database, it would be very useful and convenient to marine geologists. This system would not only be able to search for all the data based on one parameter, but also for both size and composition distributions. If possible, geostatistical methods could be combined with fractal dimensional methods. Of course, this would require enormous efforts. Before multimedia technology emerged, it was very difficult to create image databases. The emergence of large-capacity compact discs, high-speed central processing units, and high-speed digital signal processing techniques makes it possible to establish multimedia database management systems (DBMS), image-text DBMS, that involves graphs, text, images, and sound. In order to store image fields in a DBMS, we have to take into account two problems: (1) image access format and (2) image compression code standard.

Jan 1, 1994

By Ulrich O. Lange

Coal is America's most abundant energy resource. Therefore, it IS logical to assume that coal must be produced in much greater quantifies in order to make the United States self-sufficient, as far as energy is concerned by 1985. However, there are a number of obstacles which have to be overcome in order to achieve such a great task. According to one of the most outspoken American Mining men, there are three major obstacles. Those are: (1 ) Mining technology (2) Public image of the coal mining industry (3) Governmental policy toward the mining industry The following will be dealing with Shortwall Mining, which is a very specific part of mining technology and which might influence the image of the coal mining industry as well as the governmental guidelines, at least to make it easier to live with those guidelines. During recent years the operation of coal mines has been more expensive than ever. Since 1970, the cost of producing coal increased by 30% and the productivity dropped by just about the same amount. Those are alarming signs.

Jan 1, 1975

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By Vera Lúcia Othéro de Brito

Literature has shown that spinel Co-Mn ferrite have potential application in magneto-mechanical sensors, due to its relatively high magnetoelastic sensitivity. In this work, Co-Mn ferrite was processed by means of the ceramic method, using Fe2O3, MnO and Co3O4 as raw materials. Samples were liquid-phase sintered, using Bi2O3 additive as liquid-phase former. X-ray fluorescence analysis was carried out in the raw materials in order to evaluate their impurity content. Atomic absorption spectrometry analysis was used for quantifying the Co/Mn/Fe proportion in the ferrite. The microstructure of the sintered sample was analyzed by means of Scanning Electron Microscopy. The magnetization and magnetostrictive behavior of the ferrite were evaluated, obtaining curves for magnetic hysteresis, magnetostriction and magnetoelastic sensitivity. The impurity inclusions and the Bi-rich particles formed from the liquid phase were characterized. The sintered ferrite had a total magnetostriction of -126ppm, which is lower than the values reported in literature for a Co-Mn ferrite of similar composition. It was verified that sintering was carried out within a critical temperature range, in which the decomposition of Mn ferrites may occur when sintering in air. This decomposition affects the magnetic properties of the material, and it may be avoided by using controlled sintering atmospheres.

Aug 8, 2018

By N. D. Cristescu

The aim of the present paper is to show how a mathematical modeling of a creeping rock and that of an yieldable lining can allow us to obtain an optimization of the lining design and generally of the whole procedure and sequence of excavation-lining application. We follow the procedure presented by Cristescu (1989) Chap. 13, and Cristescu et al.(1987); for some other approaches see the literature mentioned, for instance, by Ladanyi and Gill (1988). We have in mind to describe the creep of the rock, i.e. the tendency of the tunnel to close in time, and to take into account that the lining itself may be deforming, i.e. possesses some rheological behavior. We start from the well known fact that "intelligent" lining, which are yielding to the pressure of the rock, may be much more successful in supporting creeping rocks than excessively strong, badly designed supports which are unable to resist to pressure of the rock, though these are oversized supports (too strong, too stiff, installed too early, etc.). In order to optimize the lining to be used for a certain rock, it is absolutely necessary to study in the laboratory the main mechanical properties of that specific rock and to formulate for it a reasonably simple mathematical model. Standard triaxial test results are quite enough to determine the model for the rock, combined with some creep tests which have to reveal the long-term behavior of rock (the so-called rheological model). What concerns the lining, we consider several kinds of linings existing today, for which a mathematical model was also formulated. One shows which is the interaction between the creeping rock? and the yielding lining and how can it be formulated in mathematical terms. Once written in mathematical terms, an optimization of the lining design and that of the excavation layout and support application sequence is possible. We will try to make the exposure as simple as possible, avoiding details and having in mind to give only a sketch of the problem, while the mathematical details could be worked out quite easy.

Jan 1, 1994

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By N Guresin, R Dunne, S Blanco

This paper presents the results of research work conducted to assess if aqueous solutions of sulfur dioxide (SO2) can be used to treat roaster calcine leach residues such that recovery of gold in this material can be achieved with subsequent application of the thiocyanate (SCN-) leaching system. The project is mainly aimed at assessing an alternative use for sulfur dioxide gas generated during flotation concentrate roasting. The calcine leach residue sample used in the study contained 2.56 g/t gold. The reason for this high level of residual gold is thought to be due to gold surface passivation by thin iron oxide films, presence of gold in solid solution with refractory iron oxides and encapsulation of gold in the structure of these iron oxides.The study was conducted in three stages. The first stage was the characterisation of a sample from a roaster calcine leach residue. The second stage in the project was a set of leaching tests to assess the feasibility of using aqueous solutions of sulfur dioxide to reductively dissolve refractory iron oxide mineral phases contained in the calcine. The final objective was to assess the efficiency of thiocyanate, a gold complexing ligand stable under acidic and oxidative conditions, to extract gold liberated during sulfur dioxide leaching.The study showed that the reductive sulfur dioxide treatment of the calcine leach residues followed by oxidative thiocyanate leaching to extract gold was not a particularly efficient process as only around 20 per cent gold could be extracted. Leaching the calcine residues by any of these systems separately also extracted the same amount of gold (12 - 14 per cent) implying that irrespective of the solution potential, the acidity helps dissolution of gold encapsulating minerals, mostly hematite, but at a very slow rate. The findings on the topic in the literature and during this study show the requirement for further technical investigations and economical analyses on two cases. The first case is to roast gold concentrates to produce magnetite rather than hematite followed by sulfur dioxide and thiocyanate leaching of magnetite containing calcines. The second case is to apply a magnetic concentration process to conventional roast-cyanidation calcine residues to produce a gold-rich magnetite concentrate that can be further treated with sulfur dioxide followed by thiocyanate leaching.For both cases, the best evaluation of the sulfur dioxide leach system in extracting residual gold from calcine leach residues will require a detailed economic analysis to find out the balance between the value of the gold recovered and the loss of revenue from acid production. There are a number of roasters that do not produce acid. In these cases, a portion of the unwanted sulfur dioxide gas can be used to recover gold in magnetite containing calcines as an economic incentive.CITATION:Guresin, N, Blanco, S and Dunne, R, 2013. Leaching roaster calcine leach residues with aqueous solutions of sulfur dioxide and thiocyanate, in Proceedings World Gold 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By H. W. Turner

Lying to the east of the Rio Grande, in central New Mexico, is a long N. and S. mountain range, broken into separate ridges at several points. These have received separate names; the mountains at the south end, near El Paso, being known as the Franklin mountains, and then, following successively, to the north, the San Andreas range, Sierra Oscura, Manzano and Sandia mountains. At the eastern base of the Sierra Oscura there are several low ridges, remarkable for their red color. All of these red ridges contain reefs of copper-ore. The eastern flanks of the Sierra Oscura are composed of limestone. Some fossils in the limestone were examined by Prof. J. P. Smith of Stanford University, who says they are Fusulina and indicate an Tipper Carboniferous age. The sandstones and shales containing the copper-reefs directly overlie this limestone (Fig. I), and are very likely of Permian age, like the similar beds in Texas, described by Mr. W. F. Cummins.* Overlying the copper-beds are red sandstones and shales in which very little copper has been found. The cupriferous zone and the red sandstones and shales are everywhere associated, and as one stands on a high point, he will see that these rocks form three main belts or lines of hills. These may be referred to as the northern, middle and southern belts. The northern belt was not visited by me, but is known to contain copper-deposits. The middle belt has a trend of N. of W. and S. of E. The copper-reefs have been traced for a distance of more than 2 miles. The southern belt has a trend of about N. 30' W. and S. 30°

Jan 1, 1903