Search Documents

By H. M. Lima, P. Wathern

There are many different words to describe mine closure, including rehabilitation, reclamation, restoration and decommissioning. Closing mining operations, mainly open pit mines, has required resolution of numerous issues. Mine closure plans involve environmental-protection issues, regulatory issues and community issues. The obvious, and often most expensive of them, is the physical rehabilitation of the disturbances and the elimination of long-term commitments and maintenance. This paper outlines mine closure planning and its important component, mine-site rehabilitation. Community consultation and involvement are also referred to as an important component of the mine-closure plans, which are required to ensure satisfactory mine site rehabilitation. Considerations of socioeconomic impact of mine closure and long-term responsibilities are presented.

Jan 1, 2000

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By A. H. Lang

"IntroductionMUCH PROSPECTING, exploration, and development work was done for uranium in Canada in 1952, chiefly in northern Saskatchewan and in the Great Bear Lake region of the northwest Territories. The outstanding feature of the year was the great amount of work done in preparing for production at the Ace mine of Eldorado Mining and Refining, Limited, in the Goldfields region . of Saskatchewan. Many private companies and prospectors were also active in this region. Most of the other parts of Canada where uranium has been found received less attention than during the last few years, partly because so much interest was taken in the Goldfields region.In presenting this short summary of the year's activities now, the writer is handicapped because the season is not yet over; some discoveries have probably not yet been announced, and there has not yet been time to digest the numerous reports that have been sent in by companies and prospectors. In any case it would be impossible to give details for most of the discoveries and properties, because that would require a long report, and because that information is classed as confidential until released by the discoverers and companies concerned. It is only possible, therefore, to give a few generalizations, a brief out-line of the activities in northern Saskatchewan, even briefer ,accounts of the work in other parts of the country, and a few details that property owners have informed the writer he may publish or that have already been published by the owners."

Jan 1, 1953

By N. Mejia, Z. Xiao, D. Fragomini, A. R. Laplante

"The adaptation to platinum-group minerals (PGMs) of a protocol developed to predict gold recovery by gravity is presented. The protocol is based on three different data sets: ore characterization of gravity-recoverable minerals, description of their behaviour in cyclones and ball mills, and performance of recovery units. Examples of these are given. It is shown that the gravity-recoverable PGM (GRPGM) content can be very high. A case study at the Clarabelle mill is presented. Sperrylite is the dominant platinum mineral, and its partition curve is very similar to that of gold, despite its lower density. Its grinding kinetics is significantly higher than for gold. As a result, sperrylite accumulates in finer sizes than native gold, but can still be recovered by gravity or flash flotation. Recovery projections based on gravity recoverable data are presented.BACKGROUNDReliable modeling of gold recovery by gravity or flash flotation from a grinding circuit is based on the ability to describe the properties of gold-bearing particles in the ore, their behaviour in grinding and classification units and the performance of the equipment used for recovery, be it gravity or flotation. This is shown in Figure 1."

Jan 1, 2004

By Mingmei Zhu, Lang Hu, Yu Wang, Hongpo Wang, Congjing Zhang

Magnetic field has a great effect on the crystallization behavior of mold flux and properties of the flux film between mold and strand, on which the surface quality of strand was deeply depended in continuous casting process. Therefore, studying the change law of the crystallization properties of mold flux in magnetic field is of great significant. In the present work, based on intensity of the applied magnetic field with the range from 0mT to 60mT, the crystallization ratio, crystal size and mineralogical phases of the flux film were discussed. The results show that crystallization ratio increases with the increasing magnetic field intensity, and the crystal size becomes bigger at the same time. The magnetic field promotes the crystallization ratio and growth speed of the crystallized grains of mold flux. However, magnetic field doesn’t change types of the mineralogical phases.

Jan 1, 2015

By John P. Harmon

A group of organic chemicals, known as wetting agents, has been developed, primarily for use in the textile industry. These chemicals have the property of reducing the surface tension of water when mixed with it in very dilute solutions. The advantage of lowered surface tension is recognized in dust-control work, and several wetting agents, have been tried by dust-control engineers with varying degrees of success. It is well-known that certain solids, coal for instance, are extremely hard to wet with plain water because of the high surface tension of water and the water-repellent action of coal. If the surface tension of the water is reduced, it can be demonstrated that the coal can be wetted easily. This is accomplished practical and at law cost by dissolving a very small percentage of wetting agent in the water that is to be used for wetting purposes. (Care should be exercised in using a wetting agent to be sure that it will not interfere with a subsequent process.) For some time, the comparative efficiency of various wetting agents has been the subject of considerable work by dust-control men at coal mines, as well as by members of the Bureau of Mines 3/, 4/, 5/, 6/. In this connection, a number of samples of air-borne dust have been collected in the mines. With the exception of dust-control measures conditions of dust generation and dissemination were maintained as, nearly uniform as possible. Samples were collected when water alone was sprayed on the cutter bar of a mining machine; various wetting agents were then successively added to the water and more samples of air-borne dust were-collected.

Jan 1, 1946

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By E. L. Raymond

The effect of heat treatment on the microstructure and resultant notch-bar rupture life of ZNCONEL alloys X- 750 and 718 was studied. It was found that the primary effect of heat treatment in rendering these alloys notch-ductile is the elimination of any y' denuded zone adjacent to the pain boundaries. The mechanisms by which such a denuded zone can arise and be eliminated by heat treatment are discussed. InCONEL Ni-Cr alloy X-750 and INCONEL Ni-Cr alloy 718 are age-hardenable austenitic materials. Alloy X-750 is used for its corrosion and oxidation resistance and high creep-rupture strength up to 1500°F. Alloy 718 is used most effectively up to 1300°F. One of the most important areas in their development has been establishment of consistently good rupture properties, especially in the presence of a stress concentration, such as imposed by a notch. A desire to improve these properties has led to extensive studies of the effect of heat treatment on the micro structure of these alloys and their performance in stress-rupture tests. In earlier investigations"~ of INCONEL* alloy X-750, *INCONEL i s a Registered Trademark of The International Nickel Co., Inc. grain boundary carbide morphology was linked with stress-rupture properties. If, during heat treatment, the carbide MZSC was precipitated in the grain bound-ary in a cellular form, poor rupture properties re-

Jan 1, 1968

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020

By Ben Murphy, Alejandro Yanez, Tatu Miettinen

"Flotation using large volume cells has grown in importance during recent years, particularly given the increasing demand for minerals whilst ore grades are decreasing. Outotec introduced the TankCell® e300 in 2007 to enable concentrator plants to process these higher tonnages. From the beginning, TankCell® e300s with FloatForce® mixing mechanisms have demonstrated good metallurgical performance with decreased operating costs and high availability. This paper deals with specific engineering challenges that need to be considered when installing these units rather than giving examples of performance. Today there are over 100 TankCell® e300s operational worldwide. As more of these units are installed new technical challenges are encountered and solutions developed to maximize their productivity. Lessons have been learnt by operators, engineering companies and the cell manufacturers on how best to design and layout these cells in modern concentrators to ensure smooth transition from design to installation to operation. This paper presents information on important design considerations and learning that has been obtained through the design, installation and commissioning of the TankCell e300 around the world. Areas pertaining to cells layout such as feed and discharge arrangements along with items of metallurgical concern such as sampling, reagent addition and the potential benefits of installing a variable speed drive on the motor will be covered in depth."

Jan 1, 2014

By Howard N. Egan

The importance of coal as the major energy source has led to wider interest in the recovery of waste coal fines as a usable product. An additional incentive for fine coal recovery has been the increased emphasis on environ- mental pollution control and conservation of the nation's natural resources, Accordingly, a series of studies and tests were performed to investigate the feasibility of the recovery, concentration, balling and pelletizing of coal fines as a marketable adjunct to existing mining and beneficiation operations. These studies were conducted at the existing operations of the Eastern Coal Corporation at Stone, Kentucky, and the Metallurgical Laboratory of Arthur G. McKee & Company in Cleveland, Ohio. The purpose of the investigations was to recover the fines from the effluent waste waters of an existing preparation plant and transform them into a high carbon, low sulfur and ash product capable of being handled with a minimum of degradation and dusting problems. The fines were relatively high in ash content prior to processing, and flotation pretreatment served a combined function of beneficiation, recovery and water clarification, The minus 28 mesh coal concentrate containing 40 to 45 percent minus 325 mesh size material had an ash content varying between 5 and 7 percent and a sulfur content of less than 0.5 percent. Chemical and size analyses of the effluent and concentrated fines are presented in Table I for comparison.

Jan 1, 1967

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001