Search Documents

By David Hatton, Jacques van Wyngaard, Matheus Vilarinho, Neymayer Pereira Lima

The flotation of Brazilian fine iron ore particles presents well-documented challenges, particularly the high entrainment of iron into the quartz (tailings) stream, resulting in significant iron losses and reduced circuit efficiency. This paper evaluates the application of Woodgrove’s Direct Flotation Reactor (DFR®) technology, which has been piloted by Vale as a potential solution to these challenges. The DFR is assessed from a pilot scale and process design perspective, with emphasis on its staged flotation mechanism, energy dissipation characteristics, and concentrate handling mechanism that together collectively enhance the selective recovery of fine iron particles. The DFR’s operation is contrasted with conventional tank cells, highlighting its improved control over bubble-particle interactions, reduced entrainment, and potential for higher selectivity. The DFR pilot plant was used to perform reverse cationic flotation of a quartz-rich froth phase to upgrade the iron ore. Pilot plant results are presented, comparing DFR performance with pilot-scale conventional flotation tests on the same feed material and relevant industrial benchmarks. This paper compares a conventional mechanical cell circuit performance and design with a proposed DFR configuration for two -45μm deslimed size fraction samples, analysing parameters such as footprint, energy efficiency, reagent consumption, and overall metallurgical performance. The findings show that DFR technology has the potential to significantly improve the fine hematite selectivity in quartz flotation for iron ore applications, offering a pathway to increased resource efficiency and reduced losses to tailings.

May 2, 2026

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

BIBLIOGRAPHY 1. Dougherty, John J. , "Control of Mine Fires", Publication of the Mining Extension Service, School of Mines, Appalachian Center, West Virginia University (1969). 2. Coal Age, "Fire, Explosions and Recovery, Federal No. 1 Mine", November, 1963. 3. Nagy, et al., "Sealing a Coal Mine Passage through a -Nor-ii-hole: A Progress Report", U.S. B. M. Publication No. 6453, (1964). 4. Murphy, et al., "Use of Fly Ash for Remote Filling of Underground Cavities and Passageways", U.S. B. M. Publication No. 7214, (1968). 5. Pennsylvania Drilling Company, Pittsburgh, Pennsylvania. Personal Review of Equipment. 6. Industrial Hazards and Communication, Division of U. S. B. M. Personal Communication with John Murphy and Merle Bowser. 7. Instrument Technology, Inc., Borescopes and CCTV Systems for Inspections of Nuclear Reactors; Personal Communication. 8. "Public Works", July, 1972. 9. The Industrial Hazards and Communications Division of the U.S. B. M. , Personal Communication regarding Cohu Model No. 2006. 10. "Bibliography on Underwater Photography and Photogrammetry", Eastman Kodak Pamphlet No. P-124. 11. Optical Properties and Visual Effects of Smoke-Stack Plumes, U.S. Department of HEW, 1967. 12. Middleton, W. E. K. , "Vision Thru the Atmosphere", Univ. of Toronto Press, 1952. 13. Kodak "High Speed Infra Red" film and Singer Corporation Model TI Silicon Vidicon TV Camera. 14. Night Vision Laboratory, Fort Belvoir, Maryland; Barnes Engineering Company, Stamford, Connecticut, Model, T-101; AGA Inc. , Secaucus, New Jersey, Model, "Thermovision" 680.

Jan 1, 1973

OF THE many categories into which scientific knowledge has been arbitrarily divided, the one which has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. To one who has had no such course or whose auld acquaintance with the subject has all but been forgot, such application is all too often thwarted by the abstruse presentations of the subject found in many of the available textbooks. AS a tool for the control of a complex process involving many chemical reactions, physical chemistry can become very valuable. The specialist who is using this tool for many purposes and perhaps contributing to its development will want to know a great deal more about it than can be included in this book. He will be interested in its history, its accomplishments and limitations, and its applications to many and varied problems. To the steelmaker or metallurgist, however, it is only one of a number of tools that he must use. He is willing to forego the detailed study of its inner workings in order to concentrate upon the development of skill in its application. It is the purpose of this chapter to present a simplified view of physical chemistry as a tool of great potential usefulness. This purpose and the desire for brevity have required the elimination of many of the gadgets with which the tool is usually adorned. It is hoped that this simplification will be conducive to clear understanding. The beginner is urged not to overlook the more extended treatments of the standard textbooks.* He is assured at the same time that the basic tool is sound and serviceable and is guaranteed to give satisfaction if regularly lubricated with common sense. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly

Jan 1, 1944

By AIME AIME

HENRY YONGE WALKER is one of Canada's numerous gifts to the American mining and metallurgical industry, having been born it1 New Brunswick 59 years ago. At eighteen he came to the United States and has since been continuously identified with what are known as the Guggenheim interests. His first position was in the capacity of clerk at the Philadelphia Smelting & Refining Co. plant of M. Guggenheim Sons at Pueblo, Colo. In 1905 he was transferred to the plant of the American Smelting & Refining Co. at Everett, Wash., as assistant manager, two years later going to the Tacoma plant in the same capacity though with added

Jan 1, 1938

By Feng Wang, Guojing Shi, Yangyang Xie, Zizong Zhu, Qiang Wu

The coal chars from northwestern part of China are characterized with high reactivity and low strength after reaction. Four type of coke-making coals selected from northwestern part of China were studied by proximate analysis, ultimate analysis, vitrinite reflectance analysis, and FTIR with curve-fitting analysis to obtain information on their chemical composition and chemical structure. The results show that the studied coals have relatively high values of final contraction of coke residue index (x) and relatively low values of maximum thickness of plastic layer (y) and average vitrinite reflectance. Based on the curve-fitting analysis of FTIR spectra, the aliphatic carbon (Cal), the aromatic carbon (Car), and the molecular structural parameters such as CH2/CH3, fa, Hal/Har, and (R/C)u are determined. The results of curve-fitting analysis indicate that the studied coals are characterized by a large amount of oxygen-containing functional groups and aliphatic side chains.

Mar 1, 2018

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By Berlen Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration, Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its princi-pal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration.

Jan 1, 1938

By John D. Sullivan, Chester R. Austin, Edwin J. Rogers

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By A. de Meyer

Zincor experienced significant losses of metallic zinc to dross during the melting of zinc cathode plates. In this study five factors affecting the formation of dross are identified from literature. Dross from both the plant and that produced in the laboratory is characterized using XRD. An empirical model, based on laboratory-scale investigations, was developed to quantify the effect these factors on their own or in combination with each other has on the amount of zinc loss to dross. The predictive capability of the model is evaluated based on the laboratory-scale investigations. Predictions are made on the effects that heat treating the cathode plates prior to melting, increasing the cathode plate thickness, washing and drying prior to melting, and loading the furnace in a controlled manner have on the amount of zinc loss to dross. Keywords: Zinc, dross, optimize, smelter, yield, losses, empirical, model, XRD.

Jan 1, 2010

By L. Sh. Tsemekhman

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

The following list comprises the names of those persons who became members during the period Sept. 10, 1919, to Oct. 10, 1919. ADAMS, R. L Chief Min. Engr., Old Ben Coal Corpn., Mine 12, Christopher, Ill. Arizumi, Hiroshi The Kuhara Min. Co., Ltd., Tokyo, Japan. BAILY, T. F Pres. & Gen'l Mgr., Electric Furnace Co., Alliance, 0. BALDWIN, A. J., Min. Engr Box 145, Pikeville, Kentucky. BALTZELL, WILL H., Chief Engr., Canadian Steel Corpn., Ltd., Ojibway, Essex Co., Ont., Canada. BANON, E. MAGAWLY, Examining Engr., Dawes Bros., Inc. 108 So. LaSalle St., Chicago, Ill. BARNES, W., Mech. Engr., Excavating Dept., Ruston & Hornsby, Ltd., Lincoln, England. BASHORE, E. GORGAS, Head Chem., The Babcock & Wilcox Co., Bayonne, N. J. BASS, A. L Supt., Hobson Silver Lead Co., Ltd., Ymir, B. C., Canada. BORN, SIDNEY, Chief Chem., Empire Gas & Fuel Co. & Associated Companies, 1100 Cherokee Ave., Bartlesville, Okla. BRADLEY, J. G,, Coal Operator, Pres.,& Gen'l Mgr., Elk River Coal & Lumber Co., Dundon, W. Va. BENNETT, G. W., Min. Engr., Sales Engr., Taylor-Wharton Iron &- Steel Co., High Bridge,. N. J. BRUFF, CHARLES E., Member firm Bradley, Bruff & Labarthe, 85 Second St., San Francisco, Cal. COLLINS, FRANK W., Chief Engr., Bradley, Bruff & Labarthe, 85 Second St., San Francisco, Cal. CONNELL, F. M., Min. Engr., Eastern Alin. & Mill. Co., Ltd., 905 Bank of Hamilton Bldg., Toronto, Ont., Canada. CooK, HARRY H., Vice-pres., Valley Mould & Iron Corgn., 137 Shenango St., Sharpsville, Pa.

Jan 11, 1919

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024

By Vic Casaletto

"IntroductionThe Canadian mining industry is under immense pressure to compete with foreign mine operations. The very survival of the Canadian mining industry is threatened by lower ore grades, environmental pressures, high cost of labour, unfriendly tax laws toward exploration and the increasing cost of new technology. In order to compete in the world market, Canadian producers and their suppliers are rethinking age old customer-supplier relationships in favour of preferred supplier relationships which can improve the profitability and enhance the competitive position of both partners.This paper attempts to redefine partnerships with suppliers in the context of a ""win-win"" objective. It will outline the measurable benefits to both partners through a representative product which highlights the keynote structure of any successful supplier partnership The Status Quo...Mines all over North America are plagued with the same recurring questions, ""Who has the best product for my operation at the lowest price... How do we know a product will perform to a supplier's projections after the sale...What do we do if the product fails to perform as expected?"" These questions have been asked by underground mining operators for decades but rarely have long-term solutions with measurable results been achieved.The LHD industry is one example of the status quo where partnerships will provide large gains toward technological advancement, reducing mobile equipment costs. The underground mining industry is out of sync with their surface counterparts in the open pit business.Partnerships with suppliers in the open pit world are not only a standard practice but a culture which has existed for decades. Open pit operators enjoy concepts which fix their mobile equipment costs for the life of the mine and hold the equipment supplier accountable for performance and fleet economics for 60 000 service hours and longer.Manufacturers are attempting to transfer this culture into the underground mining industry. Figure I illustrates the significance of a capital driven decision."

Jan 1, 1994

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983