Search Documents

By George F. Kunz

Jan 1, 1902

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By H. A. Baumann

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 1, 1950

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By D. R. Wilburn

The Bureau of Mines investigated the potential availability of magnesium from 45 properties in market economy countries (MEC's). The 38 significant deposits evaluated have demonstrated resources of approximately 29 billion short tons (st) magnesium-bearing material containing 416 million short tons (MMst) magnesium oxide (MgO). Using data it gathered, the Bureau determined the magnesium production potential for each property including a 15-pct rate of return on invested capital. Total and annual availability assessments for the next 30 yr were completed for magnesium (Mg) metal, deadburned MgO, and caustic calcined MgO. At a January 1984 market price of $1.34/Ib Mg metal, the properties evaluated could economically produce an estimated 13 MMst Mg metal. At a market price of $400/st nonmetal magnesium product, these properties could economically produce 109 MMst deadburned MgO and 43 MMst caustic MgO. These properties could produce approximately 301,000 st Mg metal, 3.0 MMst deadburned MgO, and 430,000 st caustic MgO annually at current full production levels and 1984 market prices until at least the year 2000. Total 1984 MEC production assessed in this study was 153,000 st Mg metal and 4.3 MMst nonmetallic MgO products.

Jan 1, 1986

By L. K. Eigenbrod, F. Notaro

Enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969) has placed new responsibilities on the mining industry. The new law, aimed at eventually solving the problem of pneumoconiosis, sets new respirable dust standards at 2 mg per cu m. Techniques employed to date have been shown to lack total effectiveness in meeting the prescribed standards. Since it is possible that even the new standards will eventually have to be lowered to effectively attack the medical problem, the need for new and more reliable methods of assuring clean respirable air will intensity. This paper presents, in a preliminary manner, both the present technical capability and growth potential of cryogenic technology for supplying miners with clean breathing air. Work with two sizes of prototype supplied-air (cryogenic-liquid) respiratiors in Union Carbide's Fawn Coal mine, will be described. Other potentially fabricable systems will be discussed and a preliminary assessment made of the potential cost of introducing cryogenic air breathing systems in coal mine service.

Jan 1, 1972

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012

By M. O. Magnuson

This publication describes abandoned-mine fire-control work administered by the Bureau of Mines under cooperative agreements with State and local governments. The work was done by private contractors under the supervision of Bureau engineers. The work is authorized by Public Law 738, approved August 31, 1954, and Public Law 89-4, approved March 9, 1965. Earlier work was authorized by Interior Department Appropriations Acts for fiscal years 1949-55. A total of 70 fires have been controlled under this program in the eastern bituminous region. The nature and extent of the abandoned-mine fire problem in the bituminous region is discussed, and the methods used for controlling these fires are described. The methods that have been used, either singly or in combination, include loading out and cooling the burning material, installing fire barriers, surface sealing, and water and pneumatic flushing.

Jan 1, 1974

By AIME AIME

WIDESPREAD interest in the better utilization of coal is indicated by the attendance of over seventeen hundred men interested in the pro- cessing and utilization of coal and its by-products, at Pittsburgh, Nov. 15 to 18. The conference was truly international in scope and of a scientific character, and must be considered a real success. There were dele- gates--official and unofficial-from America, Belgium, Canada, Czechoslovakia, France, Germany, Great Britain, Japan, Mexico, and Sweden. Several Federal and 28 State departments had representatives, also many colleges and universities, and many leading industrial and mining corporations throughout the country. A feature of the sessions was that papers were mostly read in full and attentively listened to, although in some cases they were of a technical nature. The proceedings were opened by the president of Carnegie Institute of Technology, Thomas C. Baker, who spoke of the importance of the conference and felt that without foreign cooperation it could not have been held. There was no need to apologize for the movement of Carnegie Institute of Technology in the matter. Coal is commanding attention in every part of the world; so is power; and coal will remain the chief source of power for generations to come. The coal chemist is working with the engineer, and nobody can forecast what developments there will be in fuel technology. This conference may be the turning point of fuel technology in America. The development and application of these new processes may be of great benefit to Pittsburgh.

Jan 1, 1926

By EDWARD B. DURHAH

(San Francisco Meeting, UCtober, 1911.) THE refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying more than 200 parts of precious metals in 1000, or, in mint parlance; over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum group that were in the bullion. This residue is relatively small, and is melted into bars and stored until sufficient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's office, laboratory, and generator-room, respectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Oct 1, 1911

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By B. J. Moore

This publication contains analyses and related source data for 252 natural gas samples from wells and pipelines in 17 States. All of the samples were obtained and analyzed during calendar year 1976 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Eighteen previous publications have presented the results of 11,065 gas analyses prior to 1976. The first 3, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 15

Jan 1, 1977

By Oliver Bowles

AUTOMOTIVE TRANSPORT by highway, which has become indispensable to modern life either in peace or war, involves the use of powerful machines, many of which travel at high speed. To start, accelerate, and stop each motor vehicle demands the use of clutch and brake. Friction is applied intensively to both these mechanisms, and their linings must therefore be of materials that will resist wear and that will not ignite with the heat of friction. Asbestos, that curious fire-resisting: natural fiber that may be woven into unburnable cloth, is eminently suitable for this special' use, and no satisfactory substitute for it has yet been found Because- asbestos is regarded as absolutely essential to all types of motor transport on land, and in addition is indispensable to. many .other kinds of machines and equipment, the situation of the- United State's with respect to supplies of-raw-material-is of special interest: From the standpoint of national self-sufficiency, conditions are far, from satisfactory, for United States mines furnish only three to four percent of the total domestic require-

Jan 1, 1938

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By W. G. McBride

INTRODUCTION Preparation of this article, at the request of the Committee on papers, has been undertaken in the hope that it may stir up helpful discussion and constructive criticism. The Canadian mining industry is in the dumps and there is no use trying to deny the fact; nor does it help to say that other industries are in as bad or a worse condition. Let us face the situation honestly and see just how serious it is. The entire financial and industrial world is in a state of depression. The gravity of the case is no doubt exaggerated by contrast with the wave of optimism and false prosperity which pre-ceded it. The prevailing gloom and pessimism are just as irrational as was the former super-optimism. As far as we mining engineers are concerned, the causes are quite beyond our control, and it is the effect upon our own industry which interests us most. This effect is an accumulation of mineral products with consequent depression in price to a point where profits have almost, if not quite, disappeared. Whether this accumulation of stocks is the result of over-production or under-consumption is difficult to say, but it would seem likely that there is a combination of the two. The introduction of selective flotation has brought about a large increase in the production of zinc, a moderate increase in the production of lead, and a comparatively small increase in copper. It has turned relatively small mines into great producers, as in the case of the Sullivan, revived expiring mines like La Cananea, and brought-in new ones like Flin Flon

Jan 1, 1931

By John B. Knaebel

This paper, describing the milling operations of the St. Joseph Lead Co. at Balmat, N. Y., is one of a series of similar papers being prepared by the United States Bureau of Mines on practice at various mills in the United States, Canada, and Mexico. The company also operates a mine end mill at Edwards, 12 miles northeast of Balmat. Mining practice in the district, as exemplified at the Edwards mine, is described in another information circular of the Bureau of Mines.3 The writer gratefully acknowledges the generous cooperation of the company officials which made this investigation possible, and wishes to thank R. J. Mechin, manager, P. W. Wolf, mill superintendent, and F. G. Kuehl, assistant mill superintendent, for their helpful assistance. Especial thanks are due J. S. Brown, geologist, for supplying information on the characteristics of the ore, and to C. F. Jackson, principal mining engineer, U. S. Bureau of Mines, for helpful suggestions.

Jan 1, 1932

By Aline Raquel Vieira Silva

A seleção e o emprego de materiais para serviços sob tensão e temperaturas elevadas envolvem diversos problemas e, portanto o estudo dos mecanismos de deformação plástica por fluência se torna extremamente desejável. Os aços ferríticos vêm sendo extensivamente usados na indústria, em componentes críticos de plantas petroquímicas e de geração de energia devido principalmente à sua elevada resistência à fluência. Em tais circunstâncias, a deformação por fluência é importante na determinação do tempo de vida do componente. Dentre os aços resistentes a altas temperaturas, a escolha pelos aços ferríticos Cr-Mo se destaca pela excelente resistência à fluência, tenacidade e resistência à corrosão, além de uma expansão térmica relativamente baixa, o que os tornam mais atrativos em aplicações com ciclos térmicos. O desenvolvimento desses aços ocorreu através de modificações na composição química, dando origem a diferentes gerações de aços com o objetivo de aumentar a resistência à fluência. A deformação por fluência até a ruptura varia com a temperatura, tensão e tempo de exposição devido à precipitação, alteração de morfologia e distribuição de precipitados. Visando compreender o desempenho dos aços ferríticos Cr-Mo em aplicações de alta temperatura a nível microestrutural, foi realizado o estudo dos mecanismos de deformação plástica por fluência desses aços, pertencentes à norma ASTM A-335, submetidos a tratamento térmico de 500ºC a 600ºC.

Aug 7, 2018

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By Allan D. Taylor

INTRODUCTION From the designer's view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do's and don'ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn't Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941