Search Documents

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By E. Swartzman

This paper presents a general re-view of the various methods of briquetting coals, with and without the aid of a binder, with special reference to the production of a suitable briquette from Nova Scotia 'fines' for re-blending with industrial coal. From the economic and technical viewpoints, either small stoker-sized briquettes made with about 4 per cent asphalt in standard low-pressure double-roll presses, or briquettes made without binder in high-pressure double-roll presses, appear to be the most reasonable solution at present.

Jan 1, 1959

By J. J. deBarbadillo

This Bureau of Mines report describes a process for recovering chromium and other metals from superalloy scrap. Laboratory-scale experiments were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the fonnation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallurgical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and iron-molybdenum residue. Recovery of the principal elements contained in the scrap is chromium--93 percent, nickel--99 percent, cobalt--96 percent, and molybdenum--92 percent.

Jan 1, 1981

By W. F. Scott, K. L. Somerville

"This paper outlines the development and inplementation of functional training at the Thompson Mine of Inco Metals Company, Manitoba Division. This training is an extension of similar methods implemented throughout the company to meet safety and health and productivity objectives. It consists of the orientation to the mine, induction in the basic mining skills, and specific training in drilling and other skills in the mine. Initial results indicated a positive effect on the safety performance and proficiency of the mine workforce.IntroductionThe primary mining method at the Thompson Mine is mechanized cut and fill, with secondary recovery of pillars by undercut and fill . These methods require a workforce of about 900 hourly operating employees to obtain capacity production of 6500 tons of ore per day.Historically, turnover of mine employees has been high and large numbers of new recruits are introduced to the mine every year. These men are recruited primarily in Manitoba, but also from distant areas of Canada; most of the se people have no previous mining experience.Training has always been an important component of mine operations. Mine supervisors and experienced miners have committed an appreciable amount of time and effort to training these new recruits. As well, training efforts have been directed toward upgrading the skills of experienced workers.Recently, a growing awareness of the significance of this training effort and its impact on accident frequency, productivity, turnover and other important parameters of the mine operation has led to a review of training methods. The training program described in this paper has resulted from this review."

Jan 1, 1981

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By Keith Whitworth

The USSR, over the last 20 years, has continued to increase its out-put year by year and it is now almost four times what it was at the end of the Second World War. In 1975, it exceeded 700 million tons of run-oi-mine coal (all ranks) which amounts to over 20 percent of world output. This rapid progress has been due to modernization of the industry, by means of increased mechanization and automation and the development of new machines and systems for underground workings and by the expansion of open-pit workings and the development and implementation of larger earthmoving machines.

Jan 1, 1977

By J. H. E. Jeffes, K. T. Jacob

Solid oxide galvanic cells, of the type: Pt,Ni-NiO | Solid electrolyte | O(metal),Cermet,Pt, were used to measure the activity coefficient of oxygen in liquid Cu at 1 100 and 1 300°C and in Pb at 1 100°C. Similar cells were used to study the activity coefficient of oxygen in the whole range of Cu + Pb alloys at 1 100°C and in Pb-rich alloys at 900 and 750°C. The results obtained are discussed in terms of proposed solution models. An equation based on the formation of 'species' of the form M(2)O in solutions of oxygen in binary alloys is shown to fit the experimental data

Dec 1, 1971

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing, and grinding methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that in many instances publication of total production costs may cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals with the methods employed by the Malvern Clay Co., Malvern, Carroll County, Ohio. The author wishes to acknowledge the assistance of the following persons: H. C. Ross, vice-president and general manager, and H. C. Dormer, secretary and treasurer.

Jan 1, 1937

By J. E. Feddock

To succeed in today's competitive coal market, coal companies must continuously improve production and lower cost. However, the coal industry's historical management practices must change to remain viable? The practices of the current day efficient coal mine manager are reviewed and examined using W. Edwards Deming's definition of management. The statistical tools, including Pareto Charts, Control Charts and Scatter Diagrams, which identify the problems management must approach differently to increase productivity at a coal mine, are discussed.

Jan 1, 1993

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining operations, the presence of remnants from past underground labors represents a significant operational challenge, especially if they are in the surroundings of high-grade zones. The existence of uncrushable elements, such as metallic support fragments of abandoned equipment, can trigger critical operational issues if they reach conveyor belts systems or primary crushers, jeopardizing the mine to plant operational continuity. These kinds of incidents lead to expensive unplanned shutdowns, the increasing of corrective maintenance events costs, and risk to meeting expected production results. This work demonstrates the application of a three-dimensional numerical modeling tool for simulating rock displacement post-blasting (by integrating key design parameters, such as blast pattern design, detonating times, charge distribution and pre and post blast surveying). The study was conducted at Andina Mine, operated by Codelco, Chile, and enabled the identification and zoning of areas with potential presence of underground hazards in displaced rock mass, using historical data from previous workings and geotechnical mapping. The displacement results were compared to the actual post-blast surveying, ensuring an acceptability level above 80%, considering both fully confined (bank opening) and free-face blasts. Additionally, this approach allows the determination of an optimal safety offset, initially set at 10 meters and currently under validation for potential reduction. The results supported the determination of safe extraction zones and the design of excavation, loading, and haulage strategies from mine to plant or stockpile, ensuring 100% reliability in the segregation of high risk materials. Implementing displacement simulations underscores their relevance in operational risk prevention and mitigation, adding value to short-term mine planning and strengthening the safety, efficiency and profitability of the open-pit mining production process.

Jan 26, 2026

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Elli Nurminen

Sulphate decomposition was studied in the conditions of a typical copper flash smelting heat recovery boiler. The aim was to determine the kinetics of the copper sulphate decomposition reactions and to find out if they are likely to take place in the process conditions prevailing in an industrial HRB. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process. Thermal decomposition of sulphates was studied by thermogravimetry. The experiments were conducted with a commercial copper sulphate, a partially sulphated copper oxide and an actual process flue dust. The main variables studied were temperature and gas composition of a N2-O2-SO2-mixture. The samples were characterized with SEM, optical microscope and XRD. Temperature affected the decomposition rate strongly but the gas composition had a minor effect on the kinetics. The decomposition was fastest in the partly sulphated oxide and slowest in commercial copper sulphate. Keywords: Sulphate decomposition, flash smelting, heat recovery boiler, flue dust

Jan 1, 2004

By AIME AIME

ARRANGEMENTS for the Annual Meeting of the Institute were well advanced at the end of December as the following program will show. Heretofore this has been printed separately, but its inclusion in the Annual Review issue of MINING AND METALLURGY will, it is hoped, make it more easily available for reference until the final program is issued, which will be distributed at the meeting. Added details will appear in the February issue. Last year's meeting drew a record crowd of over 2300 which should be exceeded this year. Early reservations at the headquarters hotel, the Waldorf-Astoria, or any other convenient hotel are desirable, as are prompt reservations for the Annual Dinner. No one need worry about too much speechmaking this year, for the honors will be awarded and accepted in a few words instead of a few paragraphs, in seconds rather than minutes.

Jan 1, 1939

By Diego L. Romero, Joy P. Romero

"IntroductionThe purpose of this paper is to explain the theory and demonstrate the industrial applications of electrostatic separation. Wabush Mines' use of this type of processing for the concentration of iron ore is unique in the industry. Other minerals are concentrated electrostatically but the process is not widely used.Typical minerals separated by electrostatic separation techniques are:Non-ConductorsAnhydriteApatiteBariteBastnasiteBerylCalciteChrysotileCorundumDiamondEpidoteFeldsparsFluoriteGarnetGypsumHornblendeKyaniteAcmiteAugiteBrookiteCassiteriteChalcopyriteChromiteColumbiteCopperDaviditeEuxeniteFerberiteFrankliniteGalenaGoldGraphiteHematiteMica (Biotite)Mica (Muscovite)MonaziteOlivinePerovskiteQuartzScheeliteSideriteSillimaniteSpheneStauroliteSulphurTopazTourmalineXenotimeZirconConductorsIlmeniteIlmenite-( High Iron)IlvaiteKoppiteMagnetiteMarmatiteMolybdenitePyriteRutileSamarskiteSphaleriteTantaliteWolframiteWulfeniteThe limitations of this process are:1. There must be a difference in conductivity between the minerals being separated.2. The size range must not be very wide.3. The specific gravity of minerals being separated should be similar or the minerals to be pinned should be lighter. 4. The feed must be dry.5. The particle shape should be more or less uniform. 6. The feed must not be high in true middling particles."

Jan 1, 1989

By E. D. Gardner

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321- 325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale de- posits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 to 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surface samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name

Jan 1, 1949

By J. W. Butwell

Anaconda has been active In the Bingham mining district near Tooele, Utah since 1914 when the company acquired International Smelting & Refining Co. Over the years both custom ores and complex Pb-Zn-Cu ores from the district were milled and smelted at International. In 1948 Anaconda acquired the property that covers the present Carr Fork ore body. Since that time active exploration took place in the 50's followed by detailed geological evaluation in the 60's. Convinced that high grade Cu deposits would be found at depth, a deep drilling program commenced in the late 60?s, with intersection of the ore zone in 1969. Following extensive deep drilling in the early 70?s, a feasibility study was conducted in 73-74 with board approval given Sept. 6, 1974. The 9,000 t/d mine-mill complex was budgeted at $217 MM over a 5 year schedule with start-up in Sept., 1979. The following discussion includes the concentrator and surface facility portion of the budget or approximately $60 MM of the scope. Special emphasis will be made on equipment selection and layout.

Jan 1, 1980

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014