Search Documents

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By G. Reuben Yourt

IN 1935, Wright-Hargreaves Mines, Limited, initiated an enlarged programme of ventilation. In the mine, surveys were made from time to time by the geological staff, and improvements in ventilation were effected to accord with progress in mining as greater depth was attained. In the summer of 1938 an engineer was trained in the technique of dust sampling. Instruments and equipment for this purpose, such as konimeter, microscope, furnace, etc., were purchased, and a suitable office, equipped with laboratory facilities, was provided. The full time of the engineer is devoted to ventilation and dust control. On surface, in the mill crushing-plant and in the assay office and sample crushing room, an elaborate arrangement of hoods and exhaust systems has been installed to eliminate the dust. These installations, however, are not described in the present paper, which deals only with an extensive programme of underground ventilation as a method of coping with high dust concentrations, increasing temperatures and high humilities.

Jan 1, 1940

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By H. Möller, M. Tshibalanganda, C. Taute, A. du Plessis, M. Leary

Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood.

Apr 1, 2021

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By R. M. Tyson

Sulfides present in the troctolitic and footwall rocks are placed into one of three major zones (hornfels, cloud, and basal) on the basis of their stratigraphic position and mineralogy. Hornfels sulfides, enriched in Fe, represent remobilized sedimentary sulfide. Sulfides from the Cloud Zone are probably magmatic and are enriched in PGE, Cu, Ni, and Ag. The basal sulfides, composing most of the ore, resulted from contamination of the magma by remobilized sedimentary sulfide. The basal sulfides exhibit a differentiation trend in their mineralogy and chemistry. PGE, Cu, and Ag are enriched with increasing differentiation which is attributed to fractionation within an immiscible sulfide liquid.

Jan 1, 1986

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

Safety remains a critical priority for the Australian mineral resource industry and will receive increased focus in the future. This is particularly evident in underground coal mines where reserves are becoming deeper and more hazardous to extract. The CSIRO, through its Exploration and Mining Division, have recently delivered on two projects aimed at providing step-change capabilities in real-time risk management and hazard control. This paper describes the key outcomes of these projects.

Jan 1, 2005

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By T. A. Lloyd

"This paper indicates the extent to which Canadian coal mine operators have taken advantage of developments in the science and technology of coal that would allow them to better satisfy changing market demands through improving the properties of their products. At some mines, no attempt is made to alter the coal from its as-mined condition, but at most mines grading into various size ranges and hand-cleaning of lump sizes is undertaken.Over-all, Canada Jags behind most of the other major world coal producers in the proportion of its coals being processed in wash plants. To some extent, this is due to the fact that a high proportion of the coal production satisfies market demands without such treatment. On the other hand, a few of the coal mines in Canada, which produce about 25 per cent of the nation's total coal output, have in operation some of the most modern coal beneficiating equipment available, including jigs, flotation cells, water cyclones, centrifuges, disc filters and thermal dryers."

Jan 1, 1968

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By T. N. McVay

The various applications of beryllium and its compounds in atomic - energy technology and a growing recognition of possible increased utilization of the metal in the aircraft and space - missile fields have resulted in increased interest in domestic and world reserves of beryllium . Unfortunately, little dependable data on beryllium resources and reserves are available , as past consumption of the element has been small and only limited prospecting and exploration work has been done . The scarcity of resource information is attributed partly to the difficulty of recognizing beryllium minerals in the field . These minerals frequently do not have distinctive characteristics of specific gravity, color , or other physical properties , that enable ready identification by the average prospector . This is particularly true of fine - grained minerals . As a result , a simple field test for identifying beryllium- bearing rock is needed . Recognizing this , technologists of the Federal Bureau of Mines investigated several of the proposed qualitative chemical tests for beryllium . This report describes various modifications of one of these methods to make it more suitable for use in the field . In the modified method , duplicate samples are fluxed -- one with potassium bifluoride and one with potassium bisulfate -- followed by dissolution of salts in water , conversion of the solution to an alkaline condition, addition of morin , and examination of the solution for fluorescence under short -wave ultraviolet light . This method provides a fast , dependable field test for beryllium minerals containing as little as 0.2 percent beryl or its equivalent . The test involves no radiation hazards , and it can be performed by persons having no technical training ; therefore , it should be useful to prospectors in discovering beryllium mineralization .

Jul 1, 1960

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

################

Aug 12, 2013

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By W. Joseph Schlitt

The use of plate and frame filter presses for dewatering cement copper at Kennecott' s Bingham Canyon precipitation plant is described. The dewatering process begins by periodically flushing a dilute copper slurry from cone precipitators to a rake thickener. The thickener underflows intermittently to an agitated surge tank which feeds the filter presses with a relatively constant slurry containing 10 to 20% solids. The presses operate with a three-stage cycle; loading, air blowing and discharging. Exothermic reactions occur during the air blow which cause actual drying as well as promoting dewatering via simple filtration. At the completion of the air blow, the presses are discharged onto a conveyor belt which transfers material to the load-out building for shipment to the smelter. An extended investigation was undertaken to relate moisture content in the filter cake to maximum press temperature, acidification of press feed, percent solids in the feed, and percent insol in the copper. Of these, press tempera¬ture and feed pH (3. 5 to 1. 0) have the greatest impact on drying. Because the discharged filter cake is hot and continues to undergo exothermic oxidation, significant drying occurs during subsequent handling so that a product containing 8 to 14% moisture is delivered to the smelter.

Jan 1, 1977

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By R. Lee-Aston

HALLOWAY mine of Tennessee Copper Co. at Copperhill, Tenn., has been under development for several years. It has two shafts, the A shaft, 1336 ft deep from the surface to the 16 level, and the B shaft, lying 500 ft to the southeast and extending 1385 ft deep from the 10 level down to the 24 level. A section through the two shafts, Fig. 1, shows the development work entailed by the proposal and the area involved. The Problem: For operational reasons it was necessary to extend the B shaft from the 10 level to surface, and the pilot hole and raising method was chosen. This method had been used to extend the Company's Boyd manshaft from the 10 to the 14 level in 1954, but no satisfactory hole surveying method had been employed. In that instance, when the hole was located it was found to be about 8 ft from its calculated position. The success of this shaft extension method lies in the ability to keep the pilot hole within the proposed shaft diameter for nearly the entire length. The approximate 670 ft of extension distance in one hole was thought to be excessive because of deflection encountered locally in other core drilling. Since a connection between the two shafts, intermediate between the surface and the 10 level, would be required at some future date, the pilot hole drilling was done in two sections. This intermediate level was fixed at the 6 level and distances became 470 ft from surface to the 6 level and 230 ft from the 6 to the 10 level. A rock pentice of 25 ft was left temporarily in place just above the 10 level.

Jan 3, 1958