Search Documents

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By Matthew John M. Krane, Christopher J. Vreeman, J. David Schloz

"A continuum mixture model of the direct chill casting process is used to model the transport phenomena and solidification behavior in the Direct Chill casting of an Al - 6 wt% Cu billet using Wagstaffs AirslipTM process. The model, which includes the transport of free-floating solid particles, can simulate the effect of a grain refiner on macrosegregation and fluid flow. Numerical predictions of sump profiles and composition and temperature fields are presented. Two 45 cm diameter billets were cast under production conditions with and without grain refiner. Temperature and composition measurements and sump profiles are compared to the numerical results. The comparison shows excellent agreement for the grain refined case. It is believed that an incorrect model assumption prevents good agreement in the non-grain refined billet. IntroductionDirect chill casting is a semi-continuous process in which molten aluminum enters the top of a water-cooled mold, is cooled, and forms a solid ingot drawn out below (Figure l(b)). The molten aluminum begins to solidify due to the cooling effect of the mold wall. As the ingot is withdrawn from the bottom of the mold, water jets impinge on the surface, directly cooling the billet and forming a solid layer around a liquid melt, commonly referred to as the sump.A particular defect that occurs in a wide range of casting processes, including the direct chill (DC) casting of aluminum alloys, is macrosegregation, the uncontrolled redistribution of alloying elements on the scale of the ingot during solidification. Macrosegregation in DC cast ingots can produce non-uniform mechanical properties [l], which affects the behavior of the metal during downstream forming and heat treat operations."

Jan 1, 2001

By R. C. Ellman

This report presents results of a series of tests on grindability of lignites and factors that influence grindability determination. All grindability tests in this investigation were made in the standard Hardgrove test apparatus. In addition to tests on standard samples of equilibrium moisture content, grindability determinations were made on air-and oven-dried samples of lignite representing the complete range of moisture content from normal bed moisture to nearly moisture-free conditions. Grindability index for all tests was calculated both by standard method and by an alternate or "corrected" method of calculation based on directly measured weight of fine-particle material produced in the grindability test. The second method of calculation allows more satisfactorily for loss of moisture during testing of high-moisture samples.

Jan 1, 1955

[ENGLISH active earth pressure adapter additive adhesion admixture, addition adsorbed water aggregate air air entrainment air hose allowable bearing value allowable pile bearing load]

Jan 1, 1994

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

Rio Tinto Iron Ore is currently working towards finalising comprehensive Native Title land access agreements, which cover all of the current eleven mines and infrastructure owned and operated by the company in Western Australia's Pilbara region. Critically, the agreements represent a mutual commitment to a long-term relationship and address many areas of concern by promoting indigenous enterprise, well-being and regional development opportunities. Our objectives in the process are to obtain the informed consent of the traditional owners for our Pilbara expansions while providing benefits to them in a way which provides lasting and substantial improvements to health, education, housing and real jobs in the mainstream economy.   To facilitate the agreement negotiations, Rio Tinto Iron Ore (RTIO) proceeded in 2005 to research and design a specific strategy around Aboriginal relations and local community engagement in the Pilbara. Wherever we operate, Rio Tinto follows a fairly simple formula in working with communities, which is comprehensively aligned to local context.   This presentation provides an overview of Rio Tinto Iron Ore's community engagement strategy in Western Australia's Pilbara region. It will also explore the establishment of regional standards on employment, business development and contracting that have been developed to ensure Indigenous people are engaged in the development of their region and are able to contribute to supporting the growth and development of mining in the area with the expectation that there is prosperity for all. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By Odette Corbu

The Canadian Trade Commissioner Service: Who we are ? A worldwide network of professionals in international business development, with preferred access to business knowledge and contacts, committed to advancing Canada?s interest ? Our global presence ?At home: 17 Regional Offices with over 100 trade officers ? Abroad: 149 offices in 101 countries with over 900 trade officers.

May 1, 2009

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By Wm. A. Haven

ON the northern part of the globe, almost since the earliest days of mankind's history. ironmaking has been practiced in one form or another. Some investigators question the generally accepted belief that copper and bronze were in earlier general use than iron, explaining the greater age and abundance of copper relics by their greater resistance to natural oxidation. However, the occurrence of copper in its natural state and its greater ease of reduction from the simpler copper minerals is a strong argument that the making and use of copper came first. Nevertheless, good evidence exists that ironmaking was practiced in ancient India and China, as well as in ancient European countries. Some interesting vestiges of those early operations still survive and have a place, in the background at least, of a discussion of modern blast-furnace practice.

Jan 1, 1940

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By T. J. Fronapfel

Impacts to ground water from mining are being comprehensively regulated in Nevada through specific requirements for design, construction, operation, permitting and closure. This program is the nation's most comprehensive for control of activities at mining operations which have the potential to cause groundwater degradation. It encompasses virtually all types of facilities, including placer, physical separation, flotation, testing, leaching and milling. Minimum design requirements are established by regulation, and must be met by each facility. Site-specific monitoring requirements are established for each facility, and are heavily emphasized. Regulatory and technical requirements and relevant permit conditions are presented and discussed.

Jan 1, 1992

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

State of California, Division of Mines, Ferry bldg., San Francisco, Calif. Walter W. Bradley, State Mineralogist. A list of publications available will be sent upon request. Bulletin 77 is a list of publications complete from 1880 to 1917 and contains synopses It is sent free. Bulletin 105, California mineral production and directory of mineral producers for 1930, brings the complete list up to date, sent free on request The Division of Mines issues principally (1) A series of Reports, (2) Bulletins, (3) Preliminary Reports, and (4) maps. The Reports were first issued biennially, later annually, and for the past few years they have taken the form of quarterly reports. The yearly subscription price for the quarterly reports is $1, payable in advance Reports and separate chapters available are Report 2, First Biennial (1892), $1, 14 (1913-1914), Chapter on mines and mineral resources of Colusa, Glenn, Lake, Mann, Napa, Solano, Sonoma, and Yolo counties, 50 cents, 15 (1915?1916), Mines and mineral resources of Butte, Lassen, Modoc, Sutter and Tehama counties, 50 cents, and Mines and mineral resources of Monterey, San Benito, San Luis Obispo, Santa Barbara and Ventura counties, 65 cents, 16 (1917-1918), Nevada County, 75 cents, Plumas County, 50 cents, Sierra County, 50 cents; 17 (1920), Mining in California during 1920, $1 75, 18 (1922), Mining m California, chapters for Aug , Sept , Oct , Dec , free, 19 (1923), Mining in California, chapters for Jan , Feb , Mar, Sept , free, 20 (1924), Quarterly chapters on mining in California (except July, out of print), 25 cents, 21 (1925), Quarterly chapters containing county reports- Jan (Sarcramento, Monterey, Orange) 25 cents, April (Calaveras, Merced, San Joaquin, Stanislaus, Ventura), 25 cents, July (Del Norte, Humboldt, San Diego) 25 cents, Oct (Siskiyou, San Luis Obispo, Santa Barbara), 25 cents; 22 (1926), Quarterly county reports: Jan. (Santa Cruz, Trinity), 25 cents, April (Shasta, San Benito, Imperial), 25 cents, July (Mann, Sonoma) and Copper in California, 25 cents, Oct (El Dorado, Inyo) Minarets District, 25 cents, 23 (1927), Quarterly county reports- Jan (Contra Costa), 25 cents, April (Aniador, Solano) Bibliography of clay

Jan 1, 1933

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By I. C. Knight

The current levels of copper smelter by-product acid production are reviewed on a regional basis, together with the possible changes in the future. There will be increasing pressure for all smelters to achieve a sulphur capture level of at least 95% by the end of the decade.

Jan 1, 1996

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

By W. K. Rankin

Achieving continued economic growth with social equity within the natural limits of the Earth's eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022