Search Documents

By J. Andrew McGlenn, Greg Emslie, Murray Gant

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet a growing population’s longterm needs. It includes a bored tunnel between two deep shafts located in North Vancouver and Burnaby, BC, Canada. The support of excavation for the 16-meter-diameter (52.5 ft) TBM launch shaft consists of 83-meter-deep (272 ft) unreinforced concrete slurry walls. This paper discusses challenges encountered during construction of the launch shaft slurry walls, namely excavation methods and slurry loss, and mitigative solutions implemented to successfully complete the shaft with minimal impact to project schedule.

Dec 1, 2022

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By S Juras

The terms measured resources and proven reserves denote the highest level of estimation confidence in all of the major classification schemes. But what do they really bring to today’s project or mine with respect to production planning and expectations? Initial reserve declaration does not need measured resources, just indicated resources. Economic viability of a project is assessed on total reserves with nary a bonus for the amount of proven reserves. Production plans are based on grade and tonnage goals that may only coincidently correspond to proven reserves. So are the measured and proven categories still relevant? Historically, and almost exclusively in underground mines, companies only allowed mining in areas of proven reserves. Some companies still follow that philosophy. But many others will mine a mixture of probable and proven reserves without hesitation. Also what of the undeveloped project in a new district – what is to be made of their declared measured resources and proven reserves? Measured resources are commonly set either by some type of proximity to data scheme or a matter of ‘feel’ based on the qualified person’s experience. The parameters for reserve conversion focus on the project as a whole and then a portion becomes classified as proven reserves almost solely based on whether the resource category is measured. So should the mining industry continue to use these categories of resource and reserve classification? This paper will present arguments about making these categories once again more relevant. A more disciplined usage of these categories may re-introduce their relevancy in public disclosures of resources and reserves. As well a more consistent usage in operations may lead to increased confidence in managing production targets and costs.

Aug 22, 2011

By X. Gumede

A model is being developed to quantify the benefits for mining houses resulting from the reduction in greenhouse gas and energy consumption by the application of innovative blast designs in addition to direct financial benefits throughout the mine to mill value chain. The conversion from shock tube initiation systems to electronics and some changes to powder factor measured on an open pit mine had previously been used to show significant improvement on blast outputs. Benefits were realised on drilling, blasting, loading, hauling and beneficiation. Quantification of the relationship between powder factor and reduced greenhouse gasses is investigated in this study. The study has highlighted new data that must be recorded and hence some assumptions were made as to fuel consumption and the energy in crushing was obtained from the Bond work equation. The mine to mill projects in an open pit platinum mine and a quarry produced energy savings and reduced greenhouse gas emissions associated with the careful application of explosives and blast innovations. The less fines project showed an increased carbon footprint. The model provides a new insight into how project feasibility should be decided based on economic and environmental viability.

Jan 1, 2012

By C. K. Leith

OTHERS here are far better qualified than I to discuss some of the specific proposals for government regulation of the oil industry. I shall make no attempt to carry oil to Oklahoma. The question of public control, however, is inherent in other branches of the mineral industry in varying degrees, and my comments will be directed mainly toward some of the trends affecting the mineral industry as a whole, as a background for your more specific consideration of oil legislation. A proud American tradition has been the insistence on freedom of competition, on equality of economic opportunity, on a policy of laissez faire. Nowhere has this principle been given wider application than in the mineral industry. The mineral field has been open to all comers, and the job of mineral exploitation has naturally attracted daring and independent spirits. The laws governing conditions of discovery and development, as well as the anti- trust laws, have been devised to foster the spirit of private initiative. The result has been the building of a mineral industry on a scale never before approximated anywhere in the world. The impetus thus gained, the methods, the technique, the financial resources, have been projected be- yond our boundaries and have made the American mineral industry the purveyor to the world for many essential commodities and first in the exploitation of the world's minerals. Our habits of individual self-reliance and success are deeply ingrained, and there is hardly an individual in the entire mineral field who does not instinctively recoil fro111 the extension of collective control, whether public or private.

Jan 1, 1932

By AIME AIME

THE Charleston Section of the A. I. M. E. held a joint meeting with the National Coal Association and the American Society of Mechanical Engineers on May 6 and 7, at which 94 members and guests were registered. Mechanical operation of coal mines was the subject discussed. First on the program was a paper entitled "Rock Dusting in the Coal Mines of West Virginia," by R. M. Lambie, chief of the Department of Mines, and Gordon MacVean. It appears in full in the current issue of MINING AND METALLURGY, p. 290. J. E. Jones of the Old Ben Coal Corp. opened this discussion by describing the method of rock dusting employed in the mines of that company, giving many interesting details, incidentally referring to the use of rock dust in fighting mine fires. He described one case where a number of troughs was brought to within 150 ft. of the fire, and rock dust had been thrown in its direction. After each trough had been thrown the party advanced a few feet, where another trough was discharged. About 10 ft. were gained on each advance, until the party found they had advanced completely over the fire.

Jan 1, 1926

By J. Gray, J. Peck

As the turn of the century approaches, traditional open pit mining methodologies and processes are being modified through the introduction and use of new technologies. As in other industries, the personal computer is dramatically changing the traditionally conservative mining industry by allowing mines of varying size and capacity to increase their productivity and efficiency through the use of easy to use, office software. Computer-based monitoring and control systems are also being used more frequently to measure and optimize, in real-time, the performances of operating equipment. When communicated to an end-user, this information can provide accurate and timely answers to questions of how much, where, when, and by whom. This capability forms the foundation of a more comprehensive, proactive management and planning facility where, ultimately, information acquired from the producing equipment will be used to optimize and control machine and human activities. As these technologies mature and become essential tools in a mine, they will eventually serve as the basis for more robotic and autonomous mining operations.

Jan 1, 1999

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By Georg Petersen

El presente texto señala el aporte de Alexander Von Humboldt en la minería a través de "Observaciones mineralógicas sobre algunos basaltos en el Rhin" (1790) y sus posteriores exploraciones geográficas al Perú. Asimismo, impulsó vigorosamente la producción aurífera en Prusia y en 1793 fundó una Escuela de Minas, elaborando su plan de estudios. . De otro lado estableció una especie de seguro contra accidentes y enfermedad para los mineros. Entre sus principales exploraciones está su viaje entre Ayabaca y Lima que se divide en 5 etapas: Ayabaca- Huancabamba; Huancabamba Desembucadura del Río Chamaya; Desembocadura del Río Chamaya - Tomependa; Tomependa - Cajamarca; y Cajamarca-Lima.

May 1, 1959

By Rachel L. Bauer, Catherine E. Johnson

Explosive demolition involves first, the use of cutting charges to sever a column and second, kicker charges to move it out of alignment. Dynamite is the traditional explosive used in kicker charges as it is inexpensive, easy to initiate, and has a consistent track record of use. Dynamite, however, has health concerns in handling, fragmentation concerns from direct contact on the beam, and availability concerns due to being manufactured at only one location in the continental United States. Recently, water-cased kicker charges have been used in industry, and research has shown that a reduced dynamite mass is possible due to the added confinement, for energetic performance, and the incompressible fluid, which aids in the transfer of explosive energy into beam movement. This research will compare two different explosives, an emulsion (DYNO AP), and binary (HELIX), to dynamite for use in kicker charges, both with and without water-casing. Emulsion is commonly used in rock blasting to create a large push or throw due to its high gas volume production which could translate to kicker charge movement. HELIX is a binary explosive commonly used by the military in breaching charges with water backing. Experimental tests placed kicker charges at the base of a hanging steel column, modifying the ballistic mortar test used to determine explosive power. The study shows that water-casing effectively reduces air overpressure and enhances explosive performance. Among the tested explosives, HELIX showed the most substantial improvements with a 1.8 dB reduction in air overpressure and a 3.2 m/s (10.5 ft/s) increase in column velocity when water-cased. Dynamite and emulsion also benefited from water casing, with decreases in air overpressure (1.1 and 0.7 dB respectively) and increases in column velocity (1.1 and 0.7 m/s (3.6 and 2.3 ft/s) respectively). This research also shows that emulsion is a viable replacement for dynamite in demolition projects, performing similarly in both traditional use and water-cased charges.

Jan 21, 2025

By D. J. Adams

Cyanide heap leaching is the predominant technology used in processing low-grade gold ores. During closure ora heap leach operation, residual cyanide must be removed from the process and waste solutions, as well as the heap. Biological cyanide oxidation is a proven, economical technology for destroying cyanide in process and waste waters and spent heaps; The use of biological cyanide degradation eliminates the need for toxic or corrosive chemical oxidizers and has- been implemented at full scale at treatment costs usually <$0.50/1,000 gal. The Applied Biosciences biological cyanide destruction (BCND?) process has been demonstrated to effectively treat cyanide, concentrations up to 350 mg/L. Treated process solutions and wastewaters also contained other contaminants such as arsenic, copper, iron, silver. selenium, mercury, nitrate and zinc, much of which was removed in the cyanide degradation process. Under optimal conditions, microorganisms can rapidly oxidize free cyanide in some process solutions from over 250 mg/L down to 0.1 mg/L in 4 to 5 hr. Cyanide is degraded to ammonia and carbon dioxide, with 50%ofthe cyanide carbon liberated as C02. In general, carbon tank based bioreactors degrade cyanide at significantly higher rates than process or wastewater pond configured treatments, which usually degrade cyanide-more rapidly than in heap treatments. Investigation of cell-free enzyme preparations as an alternative to live microbial cyanide degradation shows promise. Advantages of enzymes over live microbes for cyanide degradation include: (I) the ability to tolerate and degrade higher cyanide concentrations (> I ;000 mg/L), (2) nutrients to support live microbial cells are not required, (3) the effects of other toxic contaminants, such as metals, found in mining waters-are eliminated and (4) the potential for greatly increased kinetics.

Jan 1, 1998

By J. W. Ristori, V. R. Garfias

ONE of the most serious problems now confronting Gel- many-and one that will affect Italy even more seriously if she goes to war against England and France -is that of supplying her navy, mechanized army, and air force as well as her industrial and other needs with the necessary and related products. This problem, serious even now, will become vital should hostilities on a large scale develop.

Jan 1, 1939

By Jürgen Antrekowitsch, Thomas Griessacher

"Heavy metal containing residues are typically hazardous wastes because on the one hand, a deposition gets more and more complicated and on the other hand, the large amounts of metals like Zn, Cu, Fe and Pb represent a significant value. Thus, a post-treatment of these materials with the recovery/recycling of the metals and stabilization of the waste is not only ecological but often also economical. The therefore typically applied recycling processes utilize pyrometallurgical steps, where carbon or carbon monoxide from fossil coal and coke is used as a reducing agent, which results in large amounts of CO2 emissions. An alternative option is the application of a hydrogen-rich gas emitted in biomass utilization processes as a carbon-neutral reducing agent. Investigations in a retort process which were done at different temperatures and times showed excellent results concerning the achievable reduction rates and final contents of the heavy metals for various residues.IntroductionNowadays heavy metal containing residues like electric arc furnace dust (EAFD), dust from cupola furnaces, waelz slag, etc. are declared as hazardous wastes in a growing number of countries due to the leachability of the heavy metals in these residues. For that reason it is no longer possible to landfill these materials or use them for road construction or disposal works. Some land filling activities, carried out until now, have only been realizable because of some process modifications or cost intensive post-treatment steps of these residues. But the disposal capacities for such materials are decreasing, therefore increasing the prices. The second point for the growing disposal limitations is the stringent environmental legislations and regulations, which restrict the number and amounts of materials which can be dumped [1 – 5].From the other point of view these heavy metal containing residues usually have high contents of zinc, lead, iron, etc., which represent a significant value and therefore a big potential to recover these metals. This is why in recent years the number of recycling processes and the amount of recycled heavy metal containing residues have continuously increased. These recycling processes have the target to recover the valuable metals from the residual materials in the form of a saleable product as well as the stabilization of the slag produced in these processes [5, 6]."

Jan 1, 2011

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By A. L. Engel

This report is a compilation of the results of preliminary tests on ores containing scheelite (calcium tungstate). In most of the ores, scheelite was the only value; but several samples contained other values, such as gold, base metals, or, in one instance beryl. These investigations were made to assist the development of domestic tungsten resources by establishing satisfactory treatment methods suitable for small-scale operations. The samples were obtained through the Mining Division of the Bureau of Mines and represent, for the most part, newly discovered deposits. A previous report2/ discussed laboratory test procedures. A less detailed description of test procedures is included in the present report. As is usual in an investigation of this type, only a limited amount of work was done on most of the samples to indicate the results that could be expected from simple treatment of the particular ore. The occurrence of scheelite and the texture of the minerals present differ greatly in individual ores and must be determined and considered in establishing such details of treatment as grinding to obtain optimum liberation of the minerals, the preferred type of gravity concentration, or possible further treatment by flotation.

Jan 1, 1954

By William E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential.INTRODUCTIONThe purpose of this paper is to describe a cost approach to the valuation of mineral exploration properties and to provide some valuation examples. The particular cost approach described is the Appraised Value Method, which is best applied to mineral properties at the exploration stage.At present there are no comprehensive regulations or guidelines in Canada which specify what approaches and methods to use for the valuation of mineral properties. In this paper, the Appraised Value Method described is one method that the writer considers to be accepted industry practice for mineral properties at the exploration stage.Mineral properties are valued for a number of reasons, including mergers and acquisitions, non arm's length transactions, pricing of initial public offering of stock, support for property agreements, litigation, expropriation, and insurance claims."

Jan 1, 2003

By G. R. Belton, R. J. Fruehan

The Knudsen cell-mass spectrometer combimtion has been used to study the Fe-Al and Ag-Al liquid alloys. By application of the recently developed integration technique to the measured ion-current ratios, activities have been derived for the Fe-A1 system at 1600° C and for the Ag-Al system at 1340"C. The results are partially represented by the following equations: Internal consistency between the data on silver-rich and iron-rich alloys is demonstrated by application of the literature measurements on the distribution of aluminum between the nearly immiscible liquids iron and silver. The usual restrictions on the ratio of the mean free path of the escaping atoms to the orifice diameter of the Knudsen cell are shown not to be limiting in this technique. DESPITE the importance of a knowledge of the activity of aluminum in understanding deoxidation equilibria in molten steel, no direct studies have been made of activities in liquid Fe-A1 alloys at steel-making temperatures. Lower-temperature direct studies have, however, been carried out on aluminum-rich liquid alloys by Gross, Levi, Dewing, and Eilson&apos; at 1300°C and by Coskun and Elliott&apos; at 1315°C. Apart from phase diagram calculations by Pehlke, other determinations have been indirect and were made by measurement of the distribution of aluminum between iron and silver475 and combination of these data with extrapolated activities in the Ag-A1 system.~-% ecently, however, Woolley and Elliott have made a significant contribution by directly measuring heats of solution in the Fe-A1 system at 1600°C. The present authorslo have recently employed a Knudsen cell-mass spectrometer technique in a study of activities in iron-based liquid alloys. In this technique activities and heats of solution are determined from a series of measurements of the ratio of ion currents of the components; and since ion-current ratios are used, problems caused by changes in instrument sensitivity or cell geometry are overcome. Results obtained for the Fe-Ni system were found to be in excellent agreement with previous work, thus demonstrating the reliability of the method. The present paper describes a similar study of activities in the liquid Fe-A1 and Ag-A1 systems, this latter system being included in order that a meaningful comparison can be made with the above-mentioned indirect studies. INTEGRATION EQUATIONS A detailed derivation of the equations used to determine the thermodynamic properties from the measured ion current ratios has been given elsewhere;&apos;&apos; however it is useful to summarize them here. By the combination of the Gibbs-Duhem equation with the direct proportionality between ion-current ratios and partial pressure ratios, it was shown that for a binary system at constant temperature and pressure: where al is the activity of component 1 with pure substance as the standard state, N, is the atom fraction of component 2 in the solution, and I; and t&apos;2 are ion currents of given isotopes of the components. The activity coefficient is given by: this latter equation being more suitable for graphical integration. Combination of Eq. [l] with the Gibbs-Helmholtz equation gives an expression for the partial molar heat of mixing: EXPERIMENTAL A Bendix Time-of-Flight mass spectrometer model 12! fitted with a 107 ion source and a M-105-G-6 electron multiplier, was used to analyze the vapor effusing from the Knudsen cell. The arrangement of the Knudsen cell assembly was essentially that of the commercial instrument (Bendix model 1030) but with several modifications. Instead of heating with a single tungsten filament, a cylindrical tantalum-mesh heater was employed. Up to 1400°C simple resistance heating was used but above this temperature electron bombardment between the tantalum mesh and the tantalum cell susceptor was necessary. The temperature was measured by means of a Leeds and Northrup disappear ing-filament type optical pyrometer sighted on an essentially black-body hole in the side of the cell. Details of the temperature control, temperature measurement, and in situ calibration of the optical pyrometer can be found elsewhere.I0 In the investigation of the Fe-A1 system the Knudsen cells were constructed of thoria crucibles with fitted thoria lids (Zircoa). The cells employed in investigating the Ag-A1 alloys were made up of high-purity alumina crucibles (Morganite) with lids of recrystal-lized alumina (Lucalox). The cells were 0.370 in.

Jan 1, 1970

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980