Search Documents

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By Rick Deschamps

"Fountain Slide is located approximately 10 mi (16 km) northeast of Lillooet, British Columbia, Canada, within the Coastal Mountain Range, and has been locally active since the 1970s. The project site is located near the base of the relic Tunnel Mountain landslide. The progressive movements have posed a significant challenge to British Columbia (BC) 99, the main north-south highway in the region. The slide began affecting the British Columbia Railway Company (BCR) tracks in the 1990s. In 2004, the Canadian National Railway Company (CN) acquired BCR and, during the next 11 years, undertook measures to stabilize the rail bed. Some of the measures undertaken include numerous track realignments, a shotcrete and soil nail wall, an anchored soldier pile-and-lagging wall, and adding a row of anchors to the wall. For many years, the measures had proved successful until mid-2014 when it was observed that the slide retrogressed uphill of the tracks. Since that time, the slide movements typically ranged between 5/32 and 0.4 in (4 and 10 mm) per day, leading to extreme distortion of the earth retention system and the need for frequent track realignment.In the spring of 2016, CN issued a request for proposals (RFP) for a designbuild solution with the expectations of: (1) a safety factor greater than 1.2, (2) considering only the currently identified retrogressive blocks that extend to about 200 ft (61 m) above the track; and (3) minimizing activities outside the current easement. It was also communicated that there was a possibility that a portion of the line may have to be abandoned if the proposed remediation was cost prohibitive.The fact that the existing slide was a small fraction of the relic slide was intimidating. The relic slide extended for approximately 1.0 mi (1.6 km) above the uppermost retrogressive block that was now affecting the rail line. Other areas of concern included:"

Jan 1, 2017

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By Harry L. Siebert

Pre-splitting was substituted for line drilling to achieve stable rock slopes and reduce excavation beyond the pay line on a Connecticut highway project in 1962-63. Changes have occurred in developing rock slopes that were not foreseen by Alan Bauer and Jim Scott who in the early days understood the relationship of explosive energy to stable slopes. Cushion blasting as currently used produces slopes designed to blend or complement the natural landscape with slope holes detonated after the main body of holes. Pre-splitting is the opposite. The best results have been achieved by detonating the pre-split line of the holes first to allow readjustment of the slope plane fracture and a separate blast for the main body of loaded holes.

Jan 1, 1998

THE twenty-first birthday of the Rocky Mountain Club will be celebrated on April 11 by the Last Round-up; for, as announced at the annual meet-ing of the American Institute of Mining Engineers in February, the Club and the Institute have voted to con-solidate and formal approval by the court alone re-mains to be secured. The Rocky Mountain Club was organized some years since "to create and maintain good fellowship between the Rocky Mountain members and to further the in-terests of the Rocky Mountain States." From the first, mining men dominated it, as was natural in view of the prominence of mining in the Rocky Mountain region. A series of brilliant annual dinners were held and a site purchased for a clubhouse. A fund was raised to provide a home for the Club. Just as success was as-sured the war came and the members of the Club con-sidered it would be unpatriotic to spend money for such purpose at that time. In a spirit of patriotism the Club funds were devoted to war purposes, especially the Commission for Relief in Belgium and the caring for soldiers going to and returning from the front. So much of the money was used that at the end of the war the project for a clubhouse was out of the question with-out raising a new fund, and since 1923, the Club has been inactive. There is now in its treasury a substan-tial sum. The assets are for the most part the result of contributions made by W. B. Thompson, John Hays Hammond, and Edward H. Clark, all members of the Institute and all of whom wished to see these funds applied in a manner to leave some lasting memorial of the spirit which animated the founders and at the same time perform some useful function in the development of the region in which the Club's interest centered. It was thought that this could best be done through affilia-tion of the Club with the Institute and both organiza-tions have voted for the merger. The Club members not already in the Institute are to have the privilege of a special Rocky Mountain life membership, and the property of the Club is to be used to endow a Rocky Mountain Club fund to be used for purposes in accord with those of both the Institute and the Club and with especial reference to benefiting the Rocky Mountain region.

Jan 4, 1928

By Robert T. Gdagher, Allison Butts

EDUCATIONAL trends as reflected in curricular changes are of interest and importance in engineering educa¬tion both as matters of record and as considerations for the future. The data on which the evidence of this report is based were obtained by sending questionnaires to all schools in the United States granting the undergraduate degree in mining engineering, metallurgy, or metallurgical engineering. The questionnaire had two parts, one inquiring as to the general nature of revisions made or planned, and the other asking for information on specific courses added to or dropped from the curriculum, or given more or less time than formerly. The frequency with which curricular changes are made, even in normal times, is notable. Although it was expected that the period since 1939-40 would show numerous revisions, it was somewhat surprising to find that of 62 mining or metallurgical curricula in existence in 1939-40 and reported in the present survey, 58 had been revised or are shortly to be revised, 52 having already been changed during this period. Moreover, approximately half of the mining schools that have already revised their curricula, and probably a similar proportion of the metallurgical schools, are about to make further important changes.

Jan 1, 1948

Mother Nature controls, technical professionals model and miners decide. Decisions to explore, mine and mill. Mine decisions, mine design, planning and scheduling are subject to the quality of models û geological models, geotechnical models, resource models, density models. The closer these models are to reality, the more accurate the predicted outcome. So why is it we delegate the modelling tasks to the most junior and least experienced people? If we insist on this, we need to support them û to provide them with æexperience acceleratorsÆ. Technical mentoring is the most effective way to provide the right information at the right time. When this information (read skills) is supplied at the right time we can inject experience into the quality of our modelling and into our decision- making processes. The objective of this paper is to share those behaviours and manners that foster relationships and create frameworks for skills and experience transfer. Central to this is an understanding of how adults learn, an understanding of the basic rules of mentoring etiquette, and the three keys to building meaningful mentoring relationships. An understanding of adult learning processes and styles provides a structure within which a mentor can understand the learnerÆs perspective. Understanding the world from the learnerÆs point is critical to selecting the right language to engage, teach and transfer skills. Basic rules of mentoring etiquette like timeliness, respect and trust need to be brought into the consciousness so they can be agreed on and monitored to prevent conflicts in cultural and generational norms between the mentor and the learner.Meaningful relationships hinge on the three behaviours: truly listening, rather than just hearing; understanding the technical issues within the WIIFM (whatÆs in it for me?) question; and facilitative behaviour. Stronger and more meaningful technical mentoring relationships within our industry will bridge the generational gap and ensure we can capture and capitalise on the wealth of grey hair experience and develop an informed group of young decision-makers.

Jan 1, 2006

By C. Newman

"As underground mining continues to operate at deeper depths and in more complex multiple seam mining geometries there has been an increased demand for higher design standards in ground control safety and stability within the mining industry. For the past 20 years, NIOSH has developed and validated a number of software tools to aid in the development of safer mining environments with respect to improved roof support performance, pillar stability in longwall and room and pillar mines, formation characterization, the prediction of roof conditions, etc. These tools are available, free of charge, to the mining industry as stand-alone software packages. As cloud computing gains momentum, there is a definite need to develop internet based applications for mine design that would be easily accessible to any user at any time, including underground where permitted. This paper introduces a new web-based product which will allow for faster and easier access to existing ground control designs, on-the-fly calculations in the field as needed, and instant online collaboration between operations personnel and planning engineers. It is expected that the industry will rapidly embrace this product and, as it is common with all new innovative technologies, it will be a new paradigm for mining engineering computer applications. INTRODUCTION Since its release to the public in the late 1980's, the World Wide Web has drastically changed from a collection of static HTML web pages to a dynamic vehicle driving e-commerce, collaborative working relationships, and the mass distribution of information and media (Offutt, 2002). Recent developments in Internet capabilities, such as Cloud Computing and Software as a Service, have begun a migration away from desktop-based software in adoption of the web application (Hayes, 2008). Web applications, or web apps, are designed on the client-server architecture paradigm in which the client, or user, can interact with an application through web browsers without disrupting or installing software on potentially thousands of client computers (Nations, 2015). Currently, web-based software applications are being utilized in all business sectors and markets from commerce, finance, media, and even engineering. In fact, the Alabama Department of Transportation has developed a web-based geotechnical geographical information system (GeoGIS) for the management of and access to geotechnical and subsurface data for transportation projects across the state (Graettinger, et al., 2001). Similarly, Dyno Noble has developed a service application for explosive engineers. The Explosives Engineers' Guide application equips users with a full range of product information as well as on-demand blasting calculations for powder factor, airblast prediction, ground vibration, etc. Through the incorporation of a web server, one is able to utilize the functionality of the desktop-based software through a web browser located on any personal computer, tablet, or Smartphone (Vaughan-Nichols, 2002)."

Jan 1, 2016

By Andre L. De Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals, from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal, plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS) Biologically produced hydrogen sulfide has economically very interesting, application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less-than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals,, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine, a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By A. S. Knight

THE breaking and handling of ore is obviously the most important consideration when the layout of a new mine is contemplated. The problem must be attacked with due regard to the claim area of the property, the dip of the orebody, the anticipated percentage of payability, the width of the reef, and the amount of dislocation anticipated by dykes, faults, or sills. Among these, as far as East Geduld is concerned, the three most important items are: Area. 2,640.5 claims. Average dip 12° (from flat to 35°) Average channel width 36 inches. We are fortunate on the Witwatersrand in 'chat there is usually sufficient information available from surrounding properties to determine, within narrow limits, the factors mentioned above. With this information avail-able, the choice of layout is not limited, and it will be found that on the Witwatersrand each group has developed its own technique to suit its individual requirements. On East Geduld, the layout of the property for handling ore is known as the endless-rope haulage system. Following is a brief description of the general principles followed.

Jan 1, 1942

By Ali Dehghani Ahmad Abady

In Sarcheshmeh Copper Complex, a molybdenite floatation concentrate was produced by selective removal of copper impurities with 7 stages of cleaner floatation banks, that contains around 1% copper and 54.5% molybdenum. Mineralogical studies, physical and chemical characterizations showed that the sample contained 91% molybdenite (MoS2), 2.6% chalcopyrite (CuFeS2), 0.2%Covellite (CuS), 1.6% pyrite (FeS2) and 4.6% other nonmetallic impurities. In the present study, the removal of the copper sulfide was investigated by ferric chloride leaching for achieving a molybdenite concentrate with copper content less than 0.3%. Therefore, the application of response surface methodology (RSM) for modeling and optimization of the influence of three control parameters including ferric chloride (FeCl3) dosage, reaction temperature and reaction time, each varying in five levels, were considered, and the mathematical model for prediction of %Cu removal from molybdenite concentrate was derived. This study showed that RSM could effectively be applied for the modeling of ferric chloride leaching, and finding an economical optimum condition to achieve maximum de-coppering efficiency while consuming minimum leaching reagents. The optimum dissolution conditions to maximize Cu extraction were 200 kg/t for ferric chloride dosage, 120 min for reaction time and 80 °C for reaction temperature with a prediction of 83.20% Cu dissolution. Keywords: molybdenite concentrate, ferric chloride, leaching, response surface methodology (RSM)

Sep 1, 2012

By J. E. Moyle

The costs of labour and electric power are of prime concern to almost all industrial enterprises, and various methods of reducing their impact on production costs are constantly being developed. Automation is one of these schemes, and has received a good deal of attention in the past few years. In the mining industry, compressed air is almost universally used, and its cost is significant. Although the compressor machinery now in use has achieved a high degree of development, the hazard of explosion and fire still exists in these systems. There is thus considerable resistance in some quarters to suggestions that such installations can be safely and successfully automated. The Milliken power plant consists of two 30,000 lb. /hr. fully equipped high-pressure boilers, four H.P. air compressors, a steam turbine for stand-by power, and several L.P. compressors and vacuum pumps. With the installation of automatic and protective equipment in the machinery section, the shift force has been reduced from three to two men.

Jan 1, 1963

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By Ademar B. Lugão, Sandra R. Scagliusi, Elizabeth C. L. Cardoso

When butyl rubbers are subjected to high energy radiation, they form easy free radicals that initiate various chemical reactions. These reactions alter the molecular distribution of irradiated rubbers by crosslinking or scission affect their physical and mechanical properties. This work aims to the analysis of effect induced by γ-exposure on the crosslinking density in butyl rubbers by swelling measurements accomplished before and after irradiation at 25, 50, 100 and 200 kGy, with further evaluation of crosslinking density accomplished by Flory-Rehner equation; this is a proper procedure for the qualification of radiation resistance. It can be noticed that changes in material structure was due to build-up of new three-dimensional network in studied rubbers. Changes in crosslinking density of butyl rubber compounds emphasize that degradation mechanism is strongly influenced by gamma-radiation doses higher than 50 kGy, since chain scission process predominates over crosslinking reaction.

Mar 1, 2017

By Jr. Winters

The United States continues to be the largest producer and consumer of copper in the world. Table 1 on the following page shows several production statistics for 1974, the most recent year which the non-communist world copper industry might consider a good year, and for 1976 and 1977. In 1974 an estimated 24 percent of the non-communist world's newly mined copper was mined in the United States, and. 87 to 89 percent of that was from the western porphyry coppers. In 1976 U. S. new mine production was down to 22 percent of the non-communist world's newly mined copper, and the percentage of U. S. new mine production supplied by the porphyry coppers had risen to 89 to 91 percent. In 1977 the statistics remained the same as in 1976. U. S. porphyry copper production represented about 65 percent of U. S. refined copper consumption in 1974, rose to 75 percent in 1976, and dropped back to 61 percent in 1977 as imports of foreign copper into the United States began to swell.

Jan 1, 1978

By G. J. Hamilton

"THE Royalite-Canada Southern Coleville No. 1 gas strike of August 15th, 1951, and the closely following low gravity black-oil strike of August 23rd, were the first of a series of recent oil and gas discoveries in western Saskatchewan. They are in what is now known as the Coleville field, 25 miles north and west of Kindersley and 30 miles east of the Alberta-Saskatchewan border (Figure 1).Gas flows have been recorded in the Viking sand at daily rates of between 5 and 10 million cubic feet, and black oil of 15° A.P.I. gravity is produced from Mississippian sediments of Banff age at a daily rate .of 50 to 100 barrels on pump.Development drilling was carried on during the winter months, with very little attempt at step-out exploratory ventures. This year, however, a step-out programme to the northeast (Figure 2) is •being carried on in order to determine the position of a possible truncation of Mississippian sediments in that direction. Section 30 of the Coleville area has been fully developed on a 20-acre wellsite basis, and structural information is restricted to local rather than regional interpretation. No attempt will be made in this paper to interpret the Coleville area with respect to the regional geology in any but a general manner."

Jan 1, 1952

By Juan Ares, Enrique Fernández, Alejandro Sanz, Francisco González

"INTRODUCTION Crossrail is a subsidiary company of Transport for London created for the construction of a new transverse train line 118 km long between Maidenhead and Heathrow in the West, and Shenfield and Abbey Wood in the East, including 21 km underground below London. Crossrail C305 Eastern Running Tunnels project is the biggest contract within Crossrail Project and involved boring 11.8 km of twin tunnels through London’s city center. Crossrail C305 Project interfaced with different contracts along its alignment and therefore logistics and solutions had to be developed to minimize disruptions or interferences with other contractors and the neighborhood. The paper describes this innovative approach. C305 CONTRACT APPROACH C305 contract was split into three drives, to be excavated by four EPB TBMs 7.1m diameter, as shown in Figure 1. •,Drive Y: 8.2km long between Limmo Peninsula and Farringdon Station in the city center •,Drive Z: 2.7km long between Pudding Mill Lane and Stepney Green Junction •,Drive G: 0.9km long between Limmo Peninsula and Victoria Dock Portal in the East. Crossrail C305 Project scope of works included the excavation of TBM tunnels and shafts at Limmo Peninsula and Stepney Green (including 17m span turnout caverns), along with the requirement to traverse station and shaft structures of other Crossrail contracts. Limmo Peninsula Site was a strategic element as it was the only access point on the tunnel alignment with sufficient available area at the surface for tunnelling logistics and also connected to the Lea River, tributary of the River Thames which facilitated marine operations for segment supply and muck removal. These were the reasons for operating Drive Y & Drive G TBMs from that location. Drive Z TBMs were originally planned to be launched from Stepney Green to Pudding Mill Lane, supplying the TBMs during Drive Z excavation from Limmo Peninsula site through the excavated section of Drive Y between Limmo and Stepney Green. During the early stages of the project, a value engineering proposal with a new tunneling strategy was agreed wherein the Pudding Mill Lane contractor would provide space for TBM assembly and operation in their portal, allowing for reversing Drive Z excavation and launching the two TBMs from Pudding Mill Lane. This optimization reduced some of the shaft requirements at Stepney Green which were contingent upon critical enabling works and provided program certainty and cost savings for the full Crossrail Project. It allowed for the reuse of both the Drive Z TBMs for Drive G excavation from Limmo to Victoria Dock Portal thereby saving on the procurement of two TBMs, in addition to easier logistics for both Drives Y&Z, therefore de-risking the TBM excavation process and the C305 Project program completion."

Jan 1, 2016

By Erick F. Weiland, John W. Lindemann

Introduction Minerals exploration is one step in the mining industry's task of providing raw materials to basic industries. The industry's provision of raw materials involves identifying and evaluating resources, converting them to reserves, and intelligent, economic exploitation of these reserves. The mineral process focuses on identification and evaluation. Reserves are ore bodies and ore bodies are, by definition, wasting assets. Therefore, if an adequate provision of raw materials to basic industry is to continue, these wasting assets (ore bodies) must be replaced with new or different reserves as current reserves are depleted. Minerals exploration is a geologic problem and is fundamentally deductive, flowing from the general to the specific. Past exploration methods and philosophy have amply supplied the resources to meet the demands of an industrial society. During the past decade, however, the framework where mineral resources were identified, defined, and evaluated has changed. Mineral explorationists no longer can rely solely on the successful past methods to provide the necessary resources for our complex society. Productive explorationists must effectively and efficiently use tools and procedures that will maximize exploration efforts. Past tools need not be abandoned, but should be critically reviewed and revised in light of current scientific knowledge and technical advances. Future explorationists will view their craft not as a single discipline, but as a thoughtful integration of geophysics, geochemistry, and geostatistics for solving interrelated problems. This integration of the geosciences will lead to successful mineral exploration. Not only will the productive explorationist generate new information, he will master the use of existing data for identifying and evaluating a mineral resource. The mineral exploration process consists of incentives, ideas, finance, area, staff, time, and luck. The exploration process that stems from the interaction of these elements has three stages, each bound by a major decision point. They are selection, reconnaissance, and definition. Subsequent evaluation and exploitation phases are considered more the function of mining engineers than the exploration geologist. Mineral exploration endeavors that have been productive have three attributes fundamental to success: commitment, competence, and persistence. Commitment Commitment is believing that exploring for mineral resources is worth performing. While the mining industry is the focus of this commitment, government and society must also be committed to the concept of mineral reserve identification through exploration activity. Government demonstrates its commitment by providing access to land for exploration and, if it is successful, exploitation can take place. Realistic legislation relating to taxation, land use, reclamation, and environmental constraints is indicative of government commitment to intelligent resource use. The public must come to terms with mineral resource evaluation and extraction. Without some form of commitment from the public, availability of mineral resources vital to basic industry will be largely in the control of a foreign and potentially unstable mining industry. Commitment to a mineral resource identification-evaluation-extraction system must be shared equally by government, society, and the minerals industry. The scope and direction of this commitment varies, with the industry's commitment to explore for mineral resources being the most apparent. Industry commitment is the belief at all levels of exploration (from senior corporate executives to individual field and support staff) that exploration is worth performing, that exploration goals can be met, and that their particular organization is the best and the only group that can successfully accomplish the project. Commitment can be considered at three

Jan 11, 1983

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N'Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N'Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934